Disclaimer
How to change front suspension strut on VAUXHALL Corsavan Mk II (C) (X01) – replacement guide
downloads:
2
Views:
15
Important!
This replacement procedure can be used for:
VAUXHALL Corsavan Mk II (C) (X01) 1.3 CDTI 16V (F08), VAUXHALL Corsavan Mk II (C) (X01) 1.7 DTI 16V (F08), VAUXHALL Corsavan Mk II (C) (X01) 1.7 DI 16V (F08), VAUXHALL Corsavan Mk II (C) (X01) 1.2 16V (F08) … View more
The steps may slightly vary depending on the car design.
VAUXHALL Corsavan Mk II (C) (X01) 1.3 CDTI 16V (F08), VAUXHALL Corsavan Mk II (C) (X01) 1.7 DTI 16V (F08), VAUXHALL Corsavan Mk II (C) (X01) 1.7 DI 16V (F08), VAUXHALL Corsavan Mk II (C) (X01) 1.2 16V (F08) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Shock Absorber for Corsavan Mk II (C) (X01) and other VAUXHALL models
Alternative products

Wire brush
WD-40 spray
Copper grease
Drive socket # 9
Drive socket # 17
Drive socket # 18
Combination spanner #18
Combination spanner #19
Wheel impact socket #17
Ratchet wrench
Torque wrench
Flat screwdriver
Tap wrench
Crow bar
Hydraulic transmission jack
Hydraulic strut spring compressor
Fender cover
Wheel chock
Replacement: suspension strut – VAUXHALL CORSAVAN Mk II (C). AUTODOC experts recommend:
- Both shock struts of the front suspension should be replaced simultaneously.
- The replacement procedure is identical for the left and right shock struts of the front suspension.
- All work should be done with the engine stopped.
Replacement: suspension strut – VAUXHALL CORSAVAN Mk II (C). Recommended sequence of steps:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Secure the wheels with chocks. - Step 4
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 5Raise the front of the car and secure on supports.Step 6
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VAUXHALL CORSAVAN Mk II (C) - Step 7
Remove the wheel. - Step 8
Clean the fasteners connecting the stabiliser link to the shock strut, and those connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray. - Step 9
Unscrew the nut and remove the stabilizer rod from the shock strut. Use a combination spanner #19. Use a drive socket #18. Use a ratchet wrench. - Step 10
Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a tap wrench. - Step 11
Prop up the steering knuckle. Use a hydraulic transmission jack. - Step 12
Remove the fastening bolts. - Step 13
Disconnect the brake hose holder from the shock absorber strut. Use a crowbar. - Step 14
Disconnect the steering knuckle from the shock absorber strut. - Step 15
Unscrew the upper fastening of the shock absorber strut. Use a combination spanner #19. Use a drive socket #9. Use a ratchet wrench.Replacement: suspension strut – VAUXHALL CORSAVAN Mk II (C). Professionals recommend:To avoid injuries, hold the shock strut when undoing the fastening bolts. - Step 16
Remove the suspension strut. - Step 17
Set the shock absorber strut on the spring compressor tool.Replacement: suspension strut – VAUXHALL CORSAVAN Mk II (C). AUTODOC experts recommend:Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles. - Step 18
Compress the spring. - Step 19
Remove the strut piston rod nut. Use a combination spanner #19. Use a drive socket #9. - Step 20
Remove the shock absorber mount, boot and bump stop. - Step 21
Release the coil spring. - Step 22
Remove the spring. - Step 23
Remove the old shock absorber from the hydraulic coil spring compressor.AUTODOC recommends:Replacement: suspension strut – VAUXHALL CORSAVAN Mk II (C). Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary. - Step 24
Install the new shock absorber on the hydraulic coil spring compressor. - Step 25
Install the spring on the shock absorber. - Step 26
Compress the spring. - Step 27
Before installing a new shock absorber you should pump it manually 3-5 times. - Step 28Install the mount, boot and bump stop onto a new shock absorber.Step 29
Tighten the shock strut piston rod nut. Use a combination spanner #19. Use a drive socket #9. Use a torque wrench. Tighten it to 50 Nm torque.Replacement: suspension strut – VAUXHALL CORSAVAN Mk II (C). Tip from AUTODOC:Check to make sure the spring is positioned correctly. Avoid its misalignment. Important! Be sure to use new fasteners.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VAUXHALL Corsavan Mk2 (C) (X01) model
Popular maintenance tutorials for VAUXHALL CORSAVAN Mk II (C)
Complete guides for changing the Shock absorbers on different VAUXHALL CORSA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VAUXHALL Corsavan Mk II (C) (X01)
View more
DIY alternator repair | AUTODOC tips
How to Make a DIY Foam Sprayer | AUTODOC tips
Top 7 Manual Transmission Mistakes to Avoid | AUTODOC Tips
DIY starter repair | AUTODOC tips
Most commonly replaced car parts on VAUXHALL CORSA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME







































