Important!
This replacement procedure can be used for:
SEAT Toledo III (5P2) 1.6, SEAT Toledo III (5P2) 2.0 FSI, SEAT Toledo III (5P2) 1.9 TDI, SEAT Toledo III (5P2) 2.0 TDI 16V, SEAT Toledo III (5P2) 1.8 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TFSI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 2.0 TDI, SEAT Toledo III (5P2) 1.4 16V, SEAT Toledo III (5P2) 1.4 TSI View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Shock Absorber for Toledo III (5P2) and other SEAT models
How to change Shock absorber on Seat Toledo 3 1.9 TDI – step-by-step instructions for straightforward car repair
Shock absorber
How to change Suspension Strut on Seat Toledo 3 1.9 TDI – step-by-step instructions for straightforward car repair
Suspension Strut
Tools
Replacement: suspension strut – SEAT TOLEDO III (5P2). Tools you need:
Wire brush
WD-40 spray
Brake cleaner
Ceramic grease
Copper grease
Torque wrench
Combination spanner #10
Combination spanner #18
Drive socket # 10
Drive socket # 13
Drive socket # 16
Drive socket # 18
12-point socket # 24
21-mm strut nut socket
XZN socket bit #6
XZN socket bit #14
Shock absorber socket
Torx bit T30
HEX bit No.H6
HEX bit No.H7
Wheel impact socket #17
Ratchet wrench
Tap wrench
Hydraulic transmission jack
Fender cover
Wheel chock
Replacement: suspension strut – SEAT TOLEDO III (5P2). AUTODOC experts recommend:
  • Both shock struts of the front suspension should be replaced simultaneously.
  • The replacement procedure is identical for the left and right shock struts of the front suspension.
  • Please note: all work on the car – SEAT TOLEDO III (5P2) – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    Open the bonnet.
    Step 2
    Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
    Step 3
    How to change Shock Absorber on Seat Toledo 3 2004 - free PDF and video manuals
    Clean the plastic panel fasteners. Use a wire brush. Use WD-40 spray.
  2. Step 4
    How to replace SEAT Toledo III (5P2) 1.9 TDI 2005 Shock Absorber - step-by-step manuals and video guides
    Unscrew the plastic panel fasteners. Use Torx T30. Use a ratchet wrench.
  3. Step 5
    Seat Toledo 3 2.0 TDI 16V 2006 Shock Absorber replacement: free workshop manuals
    Remove the rubber strip.
  4. Step 6
    Changing Shock Absorber on SEAT Toledo III (5P2) 2.0 TDI 2007 by yourself
    Remove the plastic panel.
  5. Step 7
    How to remove SEAT TOLEDO 2.0 FSI 2008 Shock Absorber - online easy-to-follow instructions
    Clean the fasteners of the shock strut upper mount. Use a wire brush. Use WD-40 spray.
  6. Step 8
    How to replace Shock Absorber on SEAT Toledo III (5P2) 2009: download PDF manuals and video instructions
    Loosen the upper fasteners of the suspension strut. Use a drive socket #13. Use a ratchet wrench.
  7. Step 9
    Secure the wheels with chocks.
    Step 10
    How hard is it to do yourself: Shock Absorber replacement on Seat Toledo 3 2.0 TFSI 2004 - download illustrated guide
    Loosen the fastener of the driveshaft. Use 12-point socket No.24. Use a tap wrench.
  8. Step 11
    Need to know how to renew Shock Absorber on SEAT TOLEDO 2005? This free workshop manual will help you to do it yourself
    Loosen the wheel mounting bolts. Use wheel impact socket #17.
  9. Step 12
    Raise the car.
    Replacement: suspension strut – SEAT TOLEDO III (5P2). Professionals recommend:
    If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
    Step 13
    Changing of Shock Absorber on Seat Toledo 3 2006 won't be an issue if you follow this illustrated step-by-step guide
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. SEAT TOLEDO III (5P2)
  10. Step 14
    SEAT TOLEDO 1.9 TDI Shock Absorber replacement: online guides and video tutorials
    Remove the wheel.
  11. Step 15
    Replacing Shock Absorber on Seat Toledo 3 2008 1.9 TDI by yourself
    Clean the fastener that connects the sway bar link to the suspension strut. Use a wire brush. Use WD-40 spray.
  12. Step 16
    Toledo III (5P2) 2.0 FSI 2009 Shock Absorber DIY replacement workshop manual
    Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench.
  13. Step 17
    How to change Shock Absorber on SEAT Toledo III (5P2) 2004 - tips and tricks
    Remove the stabilizer rod.
  14. Step 18
    Step-by-step recommendations for DIY replacement Seat Toledo 3 2005 2.0 FSI Shock Absorber
    Disconnect the ABS sensor wiring.
  15. Step 19
    DIY replacement of Shock Absorber on SEAT Toledo III (5P2) 1.6 2006 is not an issue anymore with our step-by-step tutorial
    Clean the fastener that connects the brake hose bracket to the suspension strut. Use a wire brush. Use WD-40 spray.
  16. Step 20
    How to change Shock Absorber on Seat Toledo 3 2004 - free PDF and video manuals
    Unscrew the fastener that connects the brake hose bracket to the suspension strut. Use a combination spanner #10.
  17. Step 21
    How to replace SEAT Toledo III (5P2) 1.9 TDI 2005 Shock Absorber - step-by-step manuals and video guides
    Remove the brake hose bracket.
  18. Step 22
    Seat Toledo 3 2.0 TDI 16V 2006 Shock Absorber replacement: free workshop manuals
    Clean the lower fastener connecting the suspension strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
  19. Step 23
    Changing Shock Absorber on SEAT Toledo III (5P2) 2.0 TDI 2007 by yourself
    Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #18. Use XZN #14. Use a ratchet wrench.
    AUTODOC recommends:
    Important! Hold the suspension strut while unscrewing the fastening bolts. SEAT TOLEDO III (5P2)
  20. Step 24
    How to remove SEAT TOLEDO 2.0 FSI 2008 Shock Absorber - online easy-to-follow instructions
    Remove the fastening bolt.
  21. Step 25
    How to replace Shock Absorber on SEAT Toledo III (5P2) 2009: download PDF manuals and video instructions
    Clean the fasteners connecting the ball joint to the suspension control arm. Use a wire brush. Use WD-40 spray.
  22. Step 26
    How hard is it to do yourself: Shock Absorber replacement on Seat Toledo 3 2.0 TFSI 2004 - download illustrated guide
    Unscrew the fasteners connecting the ball joint to the control arm. Use a drive socket #16. Use a ratchet wrench.
  23. Step 27
    Need to know how to renew Shock Absorber on SEAT TOLEDO 2005? This free workshop manual will help you to do it yourself
    Disconnect the ball joint from the control arm.
  24. Step 28
    Unscrew the fastener connecting the drive shaft to the wheel hub.
    Step 29
    Changing of Shock Absorber on Seat Toledo 3 2006 won't be an issue if you follow this illustrated step-by-step guide
    Remove the fastening bolt.
  25. Step 30
    SEAT TOLEDO 1.9 TDI Shock Absorber replacement: online guides and video tutorials
    Detach the driveshaft from the steering knuckle.
    Replacement: suspension strut – SEAT TOLEDO III (5P2). Tip:
    Make sure that the drive shaft is not unloaded (when the car is jacked).
  26. Step 31
    Replacing Shock Absorber on Seat Toledo 3 2008 1.9 TDI by yourself
    Prop up the steering knuckle. Use a hydraulic transmission jack.
  27. Step 32
    Toledo III (5P2) 2.0 FSI 2009 Shock Absorber DIY replacement workshop manual
    Release the lower fastener connecting the shock strut to the steering knuckle. Use a special drive socket to remove the shock absorber.
  28. Step 33
    How to change Shock Absorber on SEAT Toledo III (5P2) 2004 - tips and tricks
    Disconnect the steering knuckle from the shock absorber strut.
  29. Step 34
    Step-by-step recommendations for DIY replacement Seat Toledo 3 2005 2.0 FSI Shock Absorber
    Unscrew the upper fasteners of the shock strut.
    AUTODOC recommends:
    SEAT TOLEDO III (5P2) – To avoid injury, hold the suspension strut while unscrewing the fastening bolts.
  30. Step 35
    DIY replacement of Shock Absorber on SEAT Toledo III (5P2) 1.6 2006 is not an issue anymore with our step-by-step tutorial
    Remove the suspension strut.
  31. Step 36
    How to change Shock Absorber on Seat Toledo 3 2004 - free PDF and video manuals
    Set the suspension strut on the spring compressor tool.
    AUTODOC recommends:
    Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
  32. Step 37
    How to replace SEAT Toledo III (5P2) 1.9 TDI 2005 Shock Absorber - step-by-step manuals and video guides
    Compress the spring.
  33. Step 38
    Seat Toledo 3 2.0 TDI 16V 2006 Shock Absorber replacement: free workshop manuals
    Clean the strut piston rod. Use a wire brush. Use WD-40 spray.
  34. Step 39
    Changing Shock Absorber on SEAT Toledo III (5P2) 2.0 TDI 2007 by yourself
    Remove the strut piston rod nut. Use a 21-mm strut nut socket. Use HEX No.H7. Use a ratchet wrench.
  35. Step 40
    How to remove SEAT TOLEDO 2.0 FSI 2008 Shock Absorber - online easy-to-follow instructions
    Remove the upper strut mount together with the bump stop.
  36. Step 41
    How to replace Shock Absorber on SEAT Toledo III (5P2) 2009: download PDF manuals and video instructions
    Release the coil spring.
  37. Step 42
    How hard is it to do yourself: Shock Absorber replacement on Seat Toledo 3 2.0 TFSI 2004 - download illustrated guide
    Remove the spring.
  38. Step 43
    Need to know how to renew Shock Absorber on SEAT TOLEDO 2005? This free workshop manual will help you to do it yourself
    Remove the dust boot.
    AUTODOC recommends:
    Replacement: suspension strut – SEAT TOLEDO III (5P2). Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
  39. Step 44
    Changing of Shock Absorber on Seat Toledo 3 2006 won't be an issue if you follow this illustrated step-by-step guide
    Remove the old shock absorber from the hydraulic coil spring compressor.
  40. Step 45
    SEAT TOLEDO 1.9 TDI Shock Absorber replacement: online guides and video tutorials
    Install the new shock absorber on the hydraulic coil spring compressor.
    AUTODOC recommends:
    Before installing a new shock absorber you should pump it manually 3-5 times.
  41. Step 46
    Replacing Shock Absorber on Seat Toledo 3 2008 1.9 TDI by yourself
    Install the spring on the shock absorber.
  42. Step 47
    Toledo III (5P2) 2.0 FSI 2009 Shock Absorber DIY replacement workshop manual
    Compress the spring.
  43. Step 48
    How to change Shock Absorber on SEAT Toledo III (5P2) 2004 - tips and tricks
    Install the dust boot.
  44. Step 49
    Step-by-step recommendations for DIY replacement Seat Toledo 3 2005 2.0 FSI Shock Absorber
    Install the upper strut mount together with the bump stop.
  45. Step 50
    DIY replacement of Shock Absorber on SEAT Toledo III (5P2) 1.6 2006 is not an issue anymore with our step-by-step tutorial
    Tighten the shock strut piston rod nut. Use a 21-mm strut nut socket. Use HEX No.H6. Use a torque wrench. Tighten it to 60 Nm torque.
    Replacement: suspension strut – SEAT TOLEDO III (5P2). Tip:
    Check to make sure the spring is positioned correctly. Avoid its misalignment.
  46. Step 51
    How to change Shock Absorber on Seat Toledo 3 2004 - free PDF and video manuals
    Decompress the spring.
  47. Step 52
    How to replace SEAT Toledo III (5P2) 1.9 TDI 2005 Shock Absorber - step-by-step manuals and video guides
    Treat the shock strut rod. Use copper grease.
  48. Step 53
    Seat Toledo 3 2.0 TDI 16V 2006 Shock Absorber replacement: free workshop manuals
    Remove the assembled shock strut.
  49. Step 54
    Changing Shock Absorber on SEAT Toledo III (5P2) 2.0 TDI 2007 by yourself
    Clean the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
  50. Step 55
    How to remove SEAT TOLEDO 2.0 FSI 2008 Shock Absorber - online easy-to-follow instructions
    Clean the splines of the drive shaft CV joint. Use a wire brush. Use WD-40 spray.
  51. Step 56
    How to replace Shock Absorber on SEAT Toledo III (5P2) 2009: download PDF manuals and video instructions
    Treat the splines of the driveshaft CV joint. Use copper grease.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
SEAT Toledo III (5P2) Shock Absorber replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY SEAT Toledo III (5P2) Shock Absorber replacement - online guide
Tips & tricks for your SEAT Toledo III (5P2)
View more
  • How to change Shocks on SEAT Toledo III (5P2) 1.6 - replacement tricks
    5 tools that make car repair incredibly simple | AUTODOC tips
  • Changing Shock absorbers Seat Toledo 3 1.9 TDI - Replacement Tips
    How to restore a damaged thread | AUTODOC tips
  • Maintenance Hacks - SEAT Toledo III (5P2) 2.0 TDI 16V Struts replacement guide
    What causes engine misfire? | AUTODOC
  • Replace Struts and shocks on Seat Toledo 3 - free video tips
    How and why to check your oil | AUTODOC tips