Important!

This replacement procedure can be used for:
VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 1.4 TSI 4motion, VW TIGUAN (5N_) 2.0 TSI 4motion, VW TIGUAN (5N_) 2.0 TSI 4motion, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 2.0 TDI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 2.0 TDI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 1.4 TSI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Strut Mount for TIGUAN (5N_) and other VW models

Alternative products

Top strut mount

Replacement: strut mount – VW TIGUAN (5N_). Tools you need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Copper grease 
                    
                      Combination spanner #16
                    
                      Combination spanner #18
                    
                      Drive socket # 13 
                    
                      Drive socket # 16 
                    
                      Drive socket # 18 
                    
                      Drive socket # 21 
                    
                      12-point socket # 24
                    
                      HEX bit No.H6.
                    
                      XZN socket bit # 6 
                    
                      Shock absorber socket
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Flat chisel
                    
                      Hammer
                    
                      Tap wrench
                    
                      Crow bar
                    
                      Hydraulic strut spring compressor
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

Replacement: strut mount – VW TIGUAN (5N_). AUTODOC experts recommend:

The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
All mounts of the front shock struts should be replaced simultaneously.
Be sure to replace all self-locking nuts and bolts during installation.
Please note: all work on the car – VW TIGUAN (5N_) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet.

Step 2

Secure the wheels with chocks.
Step 3

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 4

Raise the front of the car and secure on supports.
Step 5

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. VW TIGUAN (5N_)
Step 6

Remove the wheel.
Step 7

Remove the hub bearing protection cap.

Please note!
Some cars are not equipped with wheel hub caps.
Step 8

Install the wheel.

Replacement: strut mount – VW TIGUAN (5N_). Tip:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 9

Screw in the wheel bolts. Use wheel impact socket #17.
Step 10

Loosen the wheel hub bolt. Use drive 12-point socket #24. Use a tap wrench.
Step 11

Remove the cowl grille seal. Raise the wiper plastic cowl grille.
Step 12

Loosen the upper fastener of the shock strut mount. Use a drive socket #13. Use a ratchet wrench.
Step 13

Unscrew the wheel bolts.

Replacement: strut mount – VW TIGUAN (5N_). AUTODOC recommends:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 14

Remove the wheel.
Step 15

Disconnect the wiring and the brake hose from the bracket on the shock strut. Use a crowbar.
Step 16

Clean the fasteners connecting the stabiliser link to the shock strut, and those connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 17

Unscrew the nut and remove the stabilizer rod from the shock strut. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench.
Step 18

Unscrew the fastener connecting the drive shaft to the wheel hub. Use drive 12-point socket #24.
Step 19

Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #16. Use a ratchet wrench.
Step 20

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 21

Disconnect the spherical joint from the arm. Use a crowbar.
Step 22

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #18. Use a combination spanner #18. Use a tap wrench.
Step 23

Lower the hydraulic transmission jack by 10-15 cm.

AUTODOC recommends:
Replacement: strut mount – VW TIGUAN (5N_). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 24

Remove the drive shaft from the wheel hub.
Step 25

Release the lower fastener connecting the shock strut to the steering knuckle. Use a special drive socket to remove the shock absorber. Use a ratchet wrench.
Step 26

Disconnect the steering knuckle from the shock absorber strut. Use a flat metal-working chisel. Use a hammer.
Step 27

Prop up the steering knuckle. Use a hydraulic transmission jack.

Replacement: strut mount – VW TIGUAN (5N_). Tip:
Make sure that the steering knuckle is not released from load.
Step 28

Unscrew the upper fastening of the shock absorber strut.

AUTODOC recommends:
Important! Hold the suspension strut while unscrewing the fastening bolts. VW TIGUAN (5N_)
Step 29

Remove the suspension strut.
Step 30

Set the shock absorber strut on the spring compressor tool.

Replacement: strut mount – VW TIGUAN (5N_). Tip from AUTODOC experts:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 31

Compress the spring.
Step 32

Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray.
Step 33

Remove the strut piston rod nut. Use a drive socket #21. Use HEX No.H6. Use a ratchet wrench.
Step 34

Remove the shock absorber mount, boot and bump stop.
Step 35

Install the new mount, boot, and bump stop on the shock absorber.
Step 36

Tighten the shock strut piston rod nut. Use a drive socket #21. Use HEX No.H6. Use a torque wrench. Tighten it to 60 Nm torque.

Replacement: strut mount – VW TIGUAN (5N_). Tip from AUTODOC:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 37

Decompress the spring.
Step 38

Remove the assembled shock strut.
Step 39

Install the shock strut into the wheel arch.
Step 40

Secure the upper fasteners of the shock strut. Do not tighten it.

AUTODOC recommends:
VW TIGUAN (5N_) – To avoid injury, hold the suspension strut while screwing in the fastening bolts.
Step 41

Install and tighten a new bolt of the steering knuckle. Use a drive socket #18. Use a combination spanner #18. Use a torque wrench. Tighten it to 70 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 42

Remove the support from under the steering knuckle.
Step 43

Mount the drive shaft into the wheel hub.
Step 44

Attach the ball joint to the control arm.
Step 45

Tighten the ball joint fastening nut. Use a drive socket #16. Use a torque wrench. Tighten it to 60 Nm torque.
Step 46

Secure the stabilizer link on the suspension strut. Use a combination spanner #16. Use XZN #6. Use a torque wrench. Tighten it to 65 Nm torque.
Step 47

Connect the fastener of the ABS sensor cable to the shock absorber strut. Fasten the brake hose on the strut.
Step 48

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 49

Install the wheel.

Replacement: strut mount – VW TIGUAN (5N_). Professionals recommend:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 50

Screw in the wheel bolts. Use wheel impact socket #17.
Step 51

Lower the car.
Step 52

Tighten the shock strut top mount. Use a drive socket #13. Use a torque wrench. Tighten it to 15 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 53

Install and secure the cowl grille.
Step 54

Tighten the bolt connecting the drive shaft to the wheel hub. Use drive 12-point socket #24. Use a torque wrench. Tighten it to 70 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 55

Install the hub bearing protection cap.
Step 56

Tighten the wheel bolts using a criss-cross pattern. Use a torque wrench. Tighten it to 120 Nm torque.

Step 57

Remove the jacks and chocks.

Step 58

Close the hood.

Comments – 2

@user_3118598

25.11.2024 20:05

Member

No mention of refitting hub bolt to drive shaft to secure hub - no torque setting given.
- Jessica_L
  
  26.11.2024 07:49
  
  @user_3118598
  
  Moderator
  
  Our manual is for a recommendation purposes. All routine replacements and values can be found directly in the technical documentation for your vehicle or with the help of a car service center.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the VW Tiguan I (5N) model

Tiguan Mk1 tyre size

How to change rear strut mount on VW Tiguan I (5N) – replacement guide

Free download PDF
2.77 MB
How to change rear suspension lower trailing arm on VW Tiguan I (5N) – replacement guide

Free download PDF
2.59 MB
How to change front lower arm on VW TIGUAN (5N_) – replacement guide

Free download PDF
2.1 MB
How to change rear suspension lower control arm on VW Tiguan I (5N) – replacement guide

Free download PDF
2.55 MB
How to change track rod end on VW Tiguan I (5N) – replacement guide

Free download PDF
2.22 MB
How to change rear wheel bearing on VW TIGUAN (5N_) – replacement guide

Free download PDF
2.22 MB

How to change rear strut mount on VW Tiguan I (5N) – replacement guide

Free download PDF
2.77 MB
How to change front strut mount on VW TIGUAN (AD1) – replacement guide

Free download PDF
3.41 MB
How to change strut mount on a car – replacement tutorial

Universal

Free download PDF
1.04 MB
How to change front strut mount on VW Golf 6 – replacement guide

Free download PDF
4.01 MB
How to change front strut mount on VW Polo 9N – replacement guide

Free download PDF
2.08 MB
How to change front strut mount on VW Golf 5 – replacement guide

Free download PDF
3.07 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to inspect and troubleshoot your car heater when it’s not working

5K views

Published on: 11/02/2021
Top 5 possible reasons your car is shaking or vibrating

6K views

Published on: 14/02/2025
The Fast and Easy Way to Fix a Broken Wheel Stud | AUTODOC tips

9K views

Published on: 08/12/2020
5 mistakes when replacing consumables

5K views

Published on: 06/02/2025