Important!

This replacement procedure can be used for:
CITROËN Berlingo (K9) 1.5 BlueHDi 130 (ECYHZJ, ECYHZR), CITROËN Berlingo (K9) 1.5 BlueHDi 100, CITROËN Berlingo (K9) 1.2 PureTech 110, CITROËN Berlingo (K9) 1.5 BlueHDi 75, CITROËN Berlingo (K9) 1.2 PureTech 130 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Control Arm for Berlingo (K9) and other CITROËN models

Suspension arm

        Suspension arm for Berlingo (K9) Diesel (131 hp)
      
        Suspension arm for Berlingo (K9) Diesel (102 hp)
      
        Suspension arm for Berlingo (K9) Petrol (110 hp)
      
        Suspension arm for Berlingo (K9) Diesel (76 hp)
      
        Suspension arm for Berlingo (K9) Petrol (131 hp)

Replacement: front lower arm – CITROËN BERLINGO (K9). Tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Combination spanner #18
                      
                        Drive socket # 18 
                      
                        Drive socket # 21 
                      
                        Drive socket # 36 
                      
                        Torx bit T50
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Tap wrench
                      
                        Hammer
                      
                        Pin punch
                      
                        Crow bar
                      
                        Ball joint puller
                      
                        Hydraulic transmission jack
                      
                        Wheel chock

Buy tools

Replacement: front lower arm – CITROËN BERLINGO (K9). AUTODOC recommends:

The replacement procedure is identical for the left and right lower control arms.
All work should be done with the engine stopped.

Replacement: front lower arm – CITROËN BERLINGO (K9). Recommended sequence of steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

Replacement: front lower arm – CITROËN BERLINGO (K9). Tip from AUTODOC experts:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 5

Remove the wheel.
Step 6

Clean the CV axle nut cotter pin. Use a wire brush.
Step 7

Remove the CV axle nut cotter pin. Use a pin punch.
Step 8

Clean the fastener of the driveshaft. Use a wire brush. Use WD-40 spray.
Step 9

Loosen the fastener of the driveshaft. Use a drive socket #36. Use a ratchet wrench.
Step 10

Clean all joints of the arm. Use a wire brush. Use WD-40 spray.
Step 11

Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #21. Use a tap wrench.
Step 12

Disconnect the spherical joint from the arm. Use a ball joint puller.
Step 13

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 14

Disconnect the spherical joint from the arm. Use a crowbar.
Step 15

Remove the support from under the steering knuckle.

AUTODOC recommends:
Replacement: front lower arm – CITROËN BERLINGO (K9). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 16

Detach the driveshaft from the steering knuckle.

Replacement: front lower arm – CITROËN BERLINGO (K9). Tip from AUTODOC:
Make sure that the drive shaft is not unloaded (when the car is jacked).
Step 17

Unscrew the front arm fastener. Use Torx T50. Use a drive socket #21. Use a ratchet wrench.
Step 18

Remove the front fastener of the control arm. Use a pin punch. Use a hammer.
Step 19

Unscrew the rear fastener connecting the control arm to the subframe. Use Torx T50. Use a drive socket #21. Use a ratchet wrench.
Step 20

Remove the rear fastener of the control arm.
Step 21

Remove the arm. Use a crowbar.
Step 22

Clean the mounting seats and the thread of the suspension arm. Use a wire brush. Use WD-40 spray.
Step 23

Install a new arm.

Replacement: front lower arm – CITROËN BERLINGO (K9). Professionals recommend:
During the installation process, use only new bolts and nuts.Do not damage the ball joint cover.
Step 24

Install the control arm fasteners.
Step 25

Screw the front arm fastener. Use Torx T50. Use a drive socket #21. Use a ratchet wrench.
Step 26

Screw the rear arm fastener. Use Torx T50. Use a drive socket #21. Use a ratchet wrench.
Step 27

Tighten the front fastener connecting the control arm to the subframe. Use a drive socket #21. Use a torque wrench. Tighten it to 111 Nm torque.
Step 28

Tighten the rear fastener connecting the arm to the body subframe. Use a drive socket #21. Use a torque wrench. Tighten it to 111 Nm torque.
Step 29

Clean the splines of the drive shaft CV joint. Use a wire brush. Use WD-40 spray.
Step 30

Install the drive shaft.
Step 31

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
Step 32

Prop up the steering knuckle. Use a hydraulic transmission jack.

Step 33

Remove the fastening bolts.
Step 34

Disconnect the steering knuckle from the shock absorber strut.
Step 35

Attach the ball joint to the control arm.
Step 36

Remove the support from under the steering knuckle.

Replacement: front lower arm – CITROËN BERLINGO (K9). Tip from AUTODOC experts:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 37

Fix the shock absorber strut on the steering knuckle.
Step 38

Install the fastening bolts.
Step 39

Screw in the fastener that connects the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
Step 40

Tighten the lower fasteners connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a torque wrench. Tighten it to 90 Nm torque.
Step 41

Tighten the drive shaft nut. Use a drive socket #36. Use a torque wrench. Tighten it to 280 Nm torque.
Step 42

Install the CV axle nut cotter pin. Use a crowbar. Use a hammer.
Step 43

Screw the fasteners of the ball joint. Use a drive socket #21. Use a ratchet wrench.
Step 44

Tighten the ball joint fastener. Use a drive socket #21. Use a torque wrench. Tighten it to 50 nm torque.
Step 45

Treat all joints of the arm. Treat the shock strut fasteners. Use copper grease.
Step 46

Clean the wheel rim mounting seat. Use a wire brush.
Step 47

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 48

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: front lower arm – CITROËN BERLINGO (K9). After applying the spray, wait a few minutes.
Step 49

Install the wheel.

Replacement: front lower arm – CITROËN BERLINGO (K9). Tip:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 50

Screw in the wheel bolts. Use wheel impact socket #17.
Step 51

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 100 Nm torque.
Step 52

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the CITROËN Berlingo (K9) model.

Citroën Berlingo K9 tyre size

How to change front anti roll bar links on CITROËN Berlingo (K9) – replacement guide

Free download PDF
1.34 MB
How to change front brake discs on CITROËN Berlingo (K9) – replacement guide

Free download PDF
2.11 MB
How to change front windshield wipers on CITROËN Berlingo (K9) – replacement guide

Free download PDF
716.8 KB
How to change engine oil and filter on CITROËN Berlingo (K9) – replacement guide

Free download PDF
1.17 MB
How to change fuel filter on CITROËN Berlingo (K9) – replacement guide

Free download PDF
931.84 KB
How to change serpentine belt on Citroen Xsara Picasso – replacement guide

Free download PDF
1.72 MB

How to change front lower arm on CITROËN BERLINGO Box (B9) – replacement guide

Free download PDF
1.93 MB
How to change front lower arm on CITROËN BERLINGO (B9) – replacement guide

Free download PDF
1.93 MB
How to change front lower arm on Citroën Berlingo M – replacement guide

Free download PDF
3.15 MB
How to change front lower arm on CITROËN Berlingo / Berlingo First (MF, GJK, GFK) – replacement guide

Free download PDF
1.95 MB
How to change control arm on a car – replacement tutorial

Universal

Free download PDF
1.07 MB
How to change front lower arm on Citroen C3 1 – replacement guide

Free download PDF
1.92 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

What to do if your car's air conditioning isn't working properly | AUTODOC tips

6K views

Published on: 05/08/2021
How to easily repair a punctured tyre | AUTODOC tips

3K views

Published on: 25/02/2021
Things you should never do with an automatic transmission | AUTODOC tips

6K views

Published on: 26/01/2021
How to repair a chipped or cracked windscreen | AUTODOC tips

7K views

Published on: 14/12/2023