Important!

This replacement procedure can be used for:
VW Passat Saloon (362) 1.4 TSI, VW Passat Saloon (362) 1.8 TSI, VW Passat Saloon (362) 1.6 TDI, VW Passat Saloon (362) 1.4 TSI EcoFuel, VW Passat Saloon (362) 1.4 TSI MultiFuel, VW Passat Saloon (362) 2.0 TDI, VW Passat Saloon (362) 1.4 TSI … View more

The steps may slightly vary depending on the car design.

How to change front springs on VW PASSAT B7 Saloon [TUTORIAL AUTODOC]

All the parts you need to replace – Springs for Passat Saloon (362) and other VW models

Alternative products

Coil spring

2242004 METZGER Coil spring

27,70 GBP

Shop

SKCS-0040216 STARK Coil spring

28,60 GBP

Shop

SP3678 MONROE Coil spring

28,89 GBP

Shop

188C0217P RIDEX PLUS Coil spring

31,27 GBP

Shop

4095085 LESJÖFORS Coil spring

31,60 GBP

Shop

36-199563 BILSTEIN Coil spring

33,26 GBP

Shop

RH3558 KYB Coil spring

33,69 GBP

Shop

86457 SPIDAN Coil spring

41,07 GBP

Shop

993 060 SACHS Coil spring

42,22 GBP

Shop

AF-4854 OPTIMAL Coil spring

47,04 GBP

Shop

Replacement: coil springs – VW Passat B7 saloon. List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #10
                    
                      Combination spanner #18
                    
                      Drive socket # 13 
                    
                      Drive socket # 16 
                    
                      Drive socket # 18 
                    
                      Drive socket # 21 
                    
                      Drive socket # 22 
                    
                      Drive socket # 27 
                    
                      XZN socket bit # 6
                    
                      XZN socket bit # 14
                    
                      HEX bit No.H7
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Pin punch
                    
                      Flat chisel
                    
                      Hammer
                    
                      Tap wrench
                    
                      Crow bar
                    
                      Hydraulic strut spring compressor
                    
                      Hydraulic transmission jack
                    
                      Fender cover
                    
                      Wheel chock

Buy tools

Replacement: coil springs – VW Passat B7 saloon. AUTODOC experts recommend:

Both coil springs of the front suspension should be replaced simultaneously.
The replacement procedure is identical for the left and right coil springs of the front suspension.
Please note: all work on the car – VW Passat B7 saloon – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet.
Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3

Remove the cowl grille seal.
Step 4

Remove the clips of the plastic cowl grille.
Step 5

Raise the wiper plastic cowl grille.
Step 6

Clean the fasteners of the shock strut upper mount. Use a wire brush. Use WD-40 spray.
Step 7

Loosen the upper fasteners of the suspension strut. Use a drive socket #13. Use a ratchet wrench.
Step 8

Secure the wheels with chocks.

Step 9

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 10

Raise the front of the car and secure on supports.
Step 11

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW Passat B7 saloon
Step 12

Remove the wheel.
Step 13

Clean all joints of the stabiliser link. Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 14

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #18. Use a ratchet wrench.
Step 15

Remove the stabilizer rod.
Step 16

Clean the brake hose bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 17

Unscrew the brake hose fastening bracket from the shock strut. Use a combination spanner #10.
Step 18

Loosen the fastener of the driveshaft. Use a drive socket #27. Use a ratchet wrench.
Step 19

Remove the fastening bolt.
Step 20

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #18. Use XZN #14. Use a ratchet wrench.
Step 21

Clean the fasteners connecting the ball joint to the suspension control arm. Use a wire brush. Use WD-40 spray.
Step 22

Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #16. Use a ratchet wrench.
Step 23

Disconnect the ball joint from the arm. Use a crowbar.
Step 24

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 25

Detach the driveshaft from the steering knuckle. Use a pin punch. Use a hammer.
Step 26

Remove the fastening bolt.
Step 27

Release the lower fastener connecting the shock strut to the steering knuckle. Use a flat metal-working chisel. Use a hammer.
Step 28

Disconnect the steering knuckle from the shock absorber strut.
Step 29

Unscrew the upper fasteners of the shock strut.

AUTODOC recommends:
VW Passat B7 saloon – To avoid injury, hold the suspension strut while unscrewing the fastening bolts.
Step 30

Remove the suspension strut.
Step 31

Set the shock absorber strut on the spring compressor tool.

Replacement: coil springs – VW Passat B7 saloon. AUTODOC recommends:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 32

Compress the spring.
Step 33

Treat the shock strut rod. Use a wire brush. Use WD-40 spray.
Step 34

Remove the strut piston rod nut. Use a drive socket #22. Use HEX No.H7. Use a ratchet wrench.
Step 35

Remove the top strut mount.
Step 36

Release the coil spring.
Step 37

Remove the spring.
Step 38

Remove the shock absorber dust cap and the bump stop.

AUTODOC recommends:
Replacement: coil springs – VW Passat B7 saloon. Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
Step 39

Install the spring on the shock absorber.
Step 40

Compress the spring.
Step 41

Install the boot and a bump stop onto the shock absorber.
Step 42

Install the upper strut mount and the strut mount bearing.
Step 43

Tighten the shock strut piston rod nut. Use a drive socket #21. Use HEX No.H7. Use a torque wrench. Tighten it to 60 Nm torque.

Replacement: coil springs – VW Passat B7 saloon. Professionals recommend:
Check to make sure the spring is positioned correctly. Avoid its misalignment.
Step 44

Treat the shock strut rod. Use copper grease.
Step 45

Decompress the spring.
Step 46

Remove the assembled shock strut.
Step 47

Clean the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 48

Install the shock strut into the wheel arch.
Step 49

Secure the upper fasteners of the shock strut. Do not tighten it.

AUTODOC recommends:
VW Passat B7 saloon – To avoid injury, hold the suspension strut while screwing in the fastening bolts.
Step 50

Clean the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 51

Fix the shock absorber strut on the steering knuckle.
Step 52

Install the fastening bolt.
Step 53

Screw in the fastener that connects the shock strut to the steering knuckle. Use a drive socket #18. Use XZN #14. Use a ratchet wrench.
Step 54

Clean the splines of the drive shaft CV joint. Use a wire brush. Use WD-40 spray.
Step 55

Remove the support from under the steering knuckle.

AUTODOC recommends:
Replacement: coil springs – VW Passat B7 saloon. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 56

Install the drive shaft.
Step 57

Clean the ball joint mounting seat. Use a wire brush. Use WD-40 spray.
Step 58

Attach the ball joint to the control arm.
Step 59

Tighten the fasteners connecting the ball joint to the control arm. Use a drive socket #16. Use a torque wrench. Tighten it to 60 Nm torque.
Step 60

Tighten the brake hose fastening bracket to the shock strut. Use a combination spanner #10.
Step 61

Tighten the lower fastening of the shock absorber. Use a drive socket #18. Use XZN #14. Use a ratchet wrench. Use a torque wrench. Tighten it to 70 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 62

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 63

Ιnstall the transverse stabilizer link.
Step 64

Tighten the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #18. Use a drive socket #18. Use XZN #6. Use a torque wrench. Tighten it to 55 Nm torque.
Step 65

Install and tighten the drive shaft bolt. Use a drive socket #27. Use a ratchet wrench.
Step 66

Treat all joints of the arm. Treat the shock strut fasteners. Use copper grease.
Step 67

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 68

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: coil springs – VW Passat B7 saloon. After applying the spray, wait a few minutes.
Step 69

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. VW Passat B7 saloon
Step 70

Screw in the wheel bolts. Use wheel impact socket #17.
Step 71

Lower the car.
Step 72

Tighten the bolt connecting the drive shaft to the wheel hub. Use a drive socket #27. Use a torque wrench. Tighten it to 70 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 73

Tighten the wheel bolts using a criss-cross pattern. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.
Step 74

Remove the jacks and chocks.
Step 75

Tighten the upper fasteners of the shock strut. Use a drive socket #13. Use a torque wrench. Tighten it to 15 Nm torque.+90°

AUTODOC recommends:
Important! Be sure to use new fasteners.
Step 76

Treat the fasteners of the shock strut mount. Use copper grease.
Step 77

Install and secure the cowl grille.
Step 78

Install the fasteners of the wiper plastic cowl grille.
Step 79

Install the cowl grille seal.
Step 80

Remove the fender protection cover.
Step 81

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the VW Passat B7 Saloon (362) model.

VW Passat B7 Saloon tyre size

How to change rear shock absorbers on VW Passat B7 saloon – replacement guide

Free download PDF
2.43 MB
How to change front suspension strut on VW Passat B7 saloon – replacement guide

Free download PDF
4.09 MB
How to change rear coil springs on VW Passat B7 saloon – replacement guide

Free download PDF
1.63 MB
How to change rear brake pads on VW Passat B7 saloon – replacement guide

Free download PDF
2.5 MB
How to change front brake pads on VW Passat B7 saloon – replacement guide

Free download PDF
1.81 MB
How to change rear brake discs on VW Passat B7 saloon – replacement guide

Free download PDF
2.18 MB

How to change front coil springs on VW Passat Saloon (3C2) – replacement guide

Free download PDF
4.08 MB
How to change rear coil springs on VW Passat Saloon (3C2) – replacement guide

Free download PDF
1.79 MB
How to change front coil springs on VW Passat B8 Variant (3G5, CB5) – replacement guide

Free download PDF
3.89 MB
How to change front coil springs on VW Passat CC (357) – replacement guide

Free download PDF
4.07 MB
How to change front coil springs on VW Passat Variant (365) – replacement guide

Free download PDF
4.08 MB
How to change rear coil springs on VW Passat Variant (365) – replacement guide

Free download PDF
1.94 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

5 Essential Tips to Prepare Your Car for Winter | AUTODOC tips

6K views

Published on: 05/02/2024
What to do if the ABS light comes on: DIY Diagnostics Tips

7K views

Published on: 11/03/2021
When, why, and how to change engine oil | AUTODOC tips

4K views

Published on: 16/08/2024
Preventing Engine Failure: Head Gasket Inspection Tutorial | AUTODOC

10K views

Published on: 13/10/2020