Recommended replacement interval for the part category Brake pad set : 30000 km

Important!

This replacement procedure can be used for:
MERCEDES-BENZ SPRINTER 3-t Box (906) 224 (906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 209 CDI (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 211 CDI (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 213 CDI (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 215 CDI (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 218 CDI (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 210 CDI (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 216 (906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 216 CDI (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 219 CDI / BlueTEC (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 213 CDI (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 211 CDI (906.611, 906.613), MERCEDES-BENZ SPRINTER 3-t Box (906) 214 CDI (906.611, 906.613) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Brake Pads for SPRINTER 3-t Box (906) and other MERCEDES-BENZ models

Alternative products

Brake pad set

SKBP-0010126 STARK Brake pad set

22,02 GBP

Shop

37553 A.B.S. Brake pad set

22,25 GBP

Shop

SKBP-0012037 STARK Brake pad set

24,64 GBP

Shop

16710 FEBI BILSTEIN Brake pad set

24,74 GBP

Shop

SKBP-0012434 STARK Brake pad set

24,85 GBP

Shop

SKBP-0011667 STARK Brake pad set

26,15 GBP

Shop

6001400 KRAFT Brake pad set

28,02 GBP

Shop

1245.00 REMSA Brake pad set

29,73 GBP

Shop

V30-8196 VAICO Brake pad set

30,88 GBP

Shop

LP1982 DELPHI Brake pad set

33,31 GBP

Shop

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). List of the tools you'll need:

                      Wire brush
                    
                      Nylon cleaning brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Anti-squeal paste
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      HEX bit no.H6.
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Flat Screwdriver
                    
                      Brake caliper wind back tool
                    
                      Round-nose pliers
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). AUTODOC experts recommend:

Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
The replacement procedure is identical for all brake pads on the same axle.
All work should be done with the engine stopped.

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). Use the following procedure:

Step 1

Open the bonnet. Unscrew the brake fluid reservoir cap.

Step 2

Secure the wheels with chocks.
Step 3

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 4

Raise the front of the car and secure on supports.

Step 5

Unscrew the wheel bolts.

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 6

Remove the wheel.
Step 7

Remove the dust boot caps of the brake caliper guide pins.
Step 8

Disconnect the brake pad wear sensor plug. Use round-nose pliers.

Please note!
Some cars are not equipped with the brake pad wear sensor.
Step 9

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 10

Unscrew the brake caliper fastening. Use HEX No.H6. Use a ratchet wrench.
Step 11

Remove the guide pins from the brake caliper.

Step 12

Spread the brake pads. Use a crowbar.

Step 13

Remove the brake caliper.

AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 14

Remove the brake pads.

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). AUTODOC experts recommend:
Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
Step 15

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). After applying the spray, wait a few minutes.
Step 16

Remove the retaining springs of the brake pads. Use a flat screwdriver.
Step 17

Install the retaining springs of the brake pads.
Step 18

Remove the brake pad wear sensor from the brake pad. Use a flat screwdriver.

Step 19

Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). Tip from AUTODOC:
Make sure the disc surface is clean before installing the pads.
Step 20

Install the wear sensor on the brake pads.

Step 21

Install new brake pads. Use a flat screwdriver.

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). Professionals recommend:
Make sure the pads are installed with linings facing the disc.
Step 22

Treat the brake caliper piston. Use a nylon cleaning brush. Use a brake cleaner.

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 23

Press in the brake caliper piston. Use brake caliper wind back tool.
Step 24

Install the brake caliper and fix it.
Step 25

Screw in the guide pins.

Step 26

Tighten the brake caliper fasteners. Use HEX No.H6. Use a torque wrench. Tighten it to 35 Nm torque.
Step 27

Connect the brake pad wear sensor plug.
Step 28

Install the dust boot caps of the brake caliper guide pins. Use a flat screwdriver.
Step 29

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 30

Clean the brake disk surface. Use a brake cleaner.

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 31

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. MERCEDES-BENZ SPRINTER 3-t Box (906)
Step 32

Screw in the wheel bolts. Use wheel impact socket #17.
Step 33

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 130 Nm torque.
Step 34

Remove the jacks and chocks.

Replacement: brake pads – MERCEDES-BENZ SPRINTER 3-t Box (906). AUTODOC recommends:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 35

Tighten the brake fluid reservoir cap. Close the hood.

AUTODOC recommends:
MERCEDES-BENZ SPRINTER 3-t Box (906) – Press the brake pedal several times with the engine shut down until you feel the resistance built up.Slow down smoothly for first 150-200 km after the brake pads replacement. Avoid unneccessary and sharp braking to a stop.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the MERCEDES-BENZ Sprinter 3-T Van (W906) model.

Mercedes Sprinter 3t Van tyre size

How to change front windshield wipers on MERCEDES-BENZ Sprinter 3-T Van (W906) – replacement guide

Free download PDF
1.54 MB
How to change engine oil and filter on MERCEDES-BENZ Sprinter 3-T Van (W906) – replacement guide

Free download PDF
2.35 MB
How to change fuel filter on MERCEDES-BENZ SPRINTER 3-t Box (906) – replacement guide

Free download PDF
1.39 MB
How to change serpentine belt on Mercedes W245 – replacement guide

Free download PDF
1.52 MB
How to change engine oil and filter on Mercedes W204 – replacement guide

Free download PDF
1.84 MB
How to change fuel filter on Mercedes W204 – replacement guide

Free download PDF
1.64 MB

How to change front brake pads on MERCEDES-BENZ SPRINTER 3,5-t Box (906) – replacement guide

Free download PDF
1.81 MB
How to change front brake pads on MERCEDES-BENZ Sprinter 3,5-T Van (907, 910) – replacement guide

Free download PDF
1.81 MB
How to change front brake pads on MERCEDES-BENZ SPRINTER 3,5-t Platform/Chassis (906) – replacement guide

Free download PDF
1.81 MB
How to change front brake pads on MERCEDES-BENZ SPRINTER 3,5-t Platform/Chassis (907, 910) – replacement guide

Free download PDF
1.81 MB
How to change front brake pads on MERCEDES-BENZ SPRINTER 5-t Box (906) – replacement guide

Free download PDF
1.8 MB
How to change front brake pads on MERCEDES-BENZ SPRINTER 3,5-t Bus (906) – replacement guide

Free download PDF
1.81 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to Fix a Squealing Belt: Causes & Solutions | AUTODOC Expert Tips

4K views

Published on: 04/03/2021
Top 5 Mistakes to Avoid for Safe Engine Bay Repairs | AUTODOC Tips

7K views

Published on: 04/08/2023
Stop Rust Before It Starts: Top 5 Tips for Car Body Protection | AUTODOC Insights

6K views

Published on: 27/07/2023
DIY starter repair | AUTODOC tips

59K views

Published on: 31/08/2023