Recommended replacement interval for the part category Brake pad set : 30000 km

Important!

This replacement procedure can be used for:
BMW 3 Touring (E91) 316 d … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Brake Pads for 3 Touring (E91) and other BMW models

Alternative products

Brake pad set

Replacement: brake pads – BMW 3 Touring (E91). List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Anti-squeal paste
                    
                      Copper grease 
                    
                      HEX bit no.H7.
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Torque wrench
                    
                      Brake caliper wind back tool
                    
                      Flat Screwdriver
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

Replacement: brake pads – BMW 3 Touring (E91). Tip from AUTODOC experts:

Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
The replacement procedure is identical for all brake pads on the same axle.
Please note: all work on the car – BMW 3 Touring (E91) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet. Unscrew the brake fluid reservoir cap.

Step 2

Secure the wheels with chocks.

Step 3

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 4

Raise the front of the car and secure on supports.

Step 5

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. BMW 3 Touring (E91)
Step 6

Remove the wheel.
Step 7

Detach the brake caliper retaining spring. Use a flat screwdriver.
Step 8

Remove the dust boot caps of the brake caliper guide pins. Use a flat screwdriver.
Step 9

Spread the brake pads. Use a crowbar.
Step 10

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.

Step 11

Unscrew the brake caliper fastening. Use HEX No.H7. Use a ratchet wrench.
Step 12

Remove the brake caliper.

Replacement: brake pads – BMW 3 Touring (E91). AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 13

Remove the brake pads.

Replacement: brake pads – BMW 3 Touring (E91). Tip:
Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
Step 14

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: brake pads – BMW 3 Touring (E91). After applying the spray, wait a few minutes.
Step 15

Treat the brake caliper piston. Use a brake cleaner.

AUTODOC recommends:
After applying the spray, wait a few minutes.
Step 16

Press in the brake caliper piston. Use brake caliper wind back tool.
Step 17

Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.

Replacement: brake pads – BMW 3 Touring (E91). Tip:
Make sure the disc surface is clean before installing the pads.
Step 18

Install new brake pads.

Replacement: brake pads – BMW 3 Touring (E91). AUTODOC recommends:
Make sure the pads are installed with linings facing the disc.
Step 19

Install the brake caliper and fix it. Use HEX No.H7. Use a torque wrench. Tighten it to 30 Nm torque.
Step 20

Install the dust boot caps of the brake caliper guide pins.
Step 21

Install the brake caliper retaining spring. Use a flat screwdriver.
Step 22

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 23

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: brake pads – BMW 3 Touring (E91). After applying the spray, wait a few minutes.
Step 24

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. BMW 3 Touring (E91)
Step 25

Screw in the wheel bolts. Use wheel impact socket #17.
Step 26

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 nm torque.

Replacement: brake pads – BMW 3 Touring (E91). AUTODOC recommends:
Without starting the engine, press the brake pedal several times until you feel significant resistance.
Step 27

Remove the jacks and chocks.

Replacement: brake pads – BMW 3 Touring (E91). Tip from AUTODOC:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 28

Tighten the brake fluid reservoir cap. Close the hood.

AUTODOC recommends:
Slow down smoothly for first 150-200 km after the brake pads replacement. Avoid unneccessary and sharp braking to a stop.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the BMW 3 Touring (E91) model

BMW E91 tyre size

How to change rear brake discs on BMW 3 Touring (E91) – replacement guide

Free download PDF
2.18 MB
How to change rear brake pad wear sensor on BMW 3 Touring (E91) – replacement guide

Free download PDF
1.2 MB
How to change front brake pad wear sensor on BMW 3 Touring (E91) – replacement guide

Free download PDF
1.28 MB
How to change front ABS sensor on BMW 3 Touring (E91) – replacement guide

Free download PDF
1.39 MB
How to change front brake discs on BMW 3 Touring (E91) – replacement guide

Free download PDF
1.95 MB
How to change rear brake pads on BMW 3 Touring (E91) – replacement guide

Free download PDF
1.48 MB

How to change rear brake pads on BMW 3 Saloon (F30, F80) – replacement guide

Free download PDF
1.91 MB
How to change front brake pads on BMW E90 – replacement guide

Free download PDF
1.7 MB
How to change rear brake pads on BMW E90 – replacement guide

Free download PDF
1.58 MB
How to change front brake pads on BMW 3 Saloon (E46) – replacement guide

Free download PDF
1.62 MB
How to change rear brake pads on BMW 3 Saloon (E46) – replacement guide

Free download PDF
1.79 MB
How to change front brake pads on BMW E92 – replacement guide

Free download PDF
1.89 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to restore a steering wheel | AUTODOC tips

57K views

Published on: 17/02/2022
What to do if the ABS light comes on: DIY Diagnostics Tips

8K views

Published on: 11/03/2021
Coolant comparison test | AUTODOC

14K views

Published on: 18/02/2021
How to replace a timing chain yourself

20K views

Published on: 12/12/2024