How to change front anti roll bar links on BMW Z4 Roadster (E89) – replacement guide
downloads:
5
Views:
30
0
Users voted – 0
Important!
This replacement procedure can be used for:
BMW Z4 Roadster (E89) sDrive 18 i,
BMW Z4 Roadster (E89) sDrive 35 is,
BMW Z4 Roadster (E89) sDrive 35 i,
BMW Z4 Roadster (E89) sDrive 30 i,
BMW Z4 Roadster (E89) sDrive 23 i,
BMW Z4 Roadster (E89) sDrive 28 i,
BMW Z4 Roadster (E89) sDrive 20 i
…
View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for Z4 Roadster (E89) and other BMW models
Replace the stabiliser links on BMW Z4 (E89) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – BMW Z4 (E89) – should be done with the engine switched off.
Carry out replacement in the following order:
Step 1
Secure the wheels with chocks.
Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3
Raise the front of the car and secure on supports.
Step 4
Unscrew the wheel bolts.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. BMW Z4 (E89)
Step 5
Remove the wheel.
Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray.
Step 7
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #16. Use a ratchet wrench.
Step 8
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17 (2 pieces).
Step 9
Remove the stabilizer rod.
Replacement: anti roll bar links – BMW Z4 (E89). Tip from AUTODOC experts:
Examine stabiliser bushes. Replace them if needed.
Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 11
Install a new rod, tighten the fasteners.
Step 12
Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17 (2 pieces). Use a torque wrench. Tighten it to 58 Nm torque.
Step 13
Tighten the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #17. Use a drive socket #16. Use a torque wrench. Tighten it to 58 Nm torque.
Step 14
Treat all joints of the stabiliser link. Use copper grease.
Step 15
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 16
Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends:
Replacement: anti roll bar links – BMW Z4 (E89). After applying the spray, wait a few minutes.
Step 17
Install the wheel.
AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. BMW Z4 (E89)
Step 18
Screw in the wheel bolts. Use wheel impact socket #17.
Step 19
Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 nm torque.
Step 20
Remove the jacks and chocks.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.