Important!

This replacement procedure can be used for:
BMW 3 Touring (E36) 320i, BMW 3 Touring (E36) 328i, BMW 3 Touring (E36) 318 tds, BMW 3 Touring (E36) 325tds, BMW 3 Touring (E36) 323i, BMW 3 Touring (E36) 318i, BMW 3 Touring (E36) 316i … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – BMW 3 Touring (E36). Tools you might need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #13
                    
                      Combination spanner #16
                    
                      Combination spanner #17
                    
                      Drive socket # 13
                    
                      Drive socket # 16
                    
                      Drive socket # 17
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Hydraulic transmission jack
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on BMW 3 Touring (E36) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – BMW 3 Touring (E36) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the front of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. BMW 3 Touring (E36)
Step 5

Remove the wheel.
Step 6

Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #13. Use a drive socket #13. Use a ratchet wrench.
Step 8

Remove the fastening bolt.
Step 9

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use a drive socket #16. Use a ratchet wrench.
Step 10

Remove the stabilizer rod.

Replacement: anti roll bar links – BMW 3 Touring (E36). AUTODOC experts recommend:
Examine the stabiliser bushes. Replace them if necessary.
Step 11

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 12

Ιnstall the transverse stabilizer link.
Step 13

Install the fastening bolt.

Step 14

Tighten the stabiliser link fastener. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
Step 15

Support the arm. Use a hydraulic transmission jack.
Step 16

Tighten the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #17. Use a drive socket #17. Use a torque wrench. Tighten it to 42 Nm torque.
Step 17

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #17. Use a drive socket #17. Use a torque wrench. Tighten it to 59 Nm torque.
Step 18

Remove the support from under the arm.

AUTODOC recommends:
Replacement: anti roll bar links – BMW 3 Touring (E36). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 19

Treat all joints of the stabiliser link. Use copper grease.
Step 20

Clean the wheel rim mounting seat. Use a wire brush.
Step 21

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 22

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – BMW 3 Touring (E36). After applying the spray, wait a few minutes.
Step 23

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. BMW 3 Touring (E36)
Step 24

Screw in the wheel bolts. Use wheel impact socket #17.
Step 25

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.
Step 26

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the BMW 3 Touring (E36) model

BMW E36 Touring tyre size

How to change rear suspension lower control arm on BMW 3 Touring (E36) – replacement guide

Free download PDF
1.92 MB
How to change front wheel bearing on BMW 3 Touring (E36) – replacement guide

Free download PDF
2.07 MB
How to change front strut mount on BMW 3 Touring (E36) – replacement guide

Free download PDF
2.58 MB
How to change rear anti roll bar links on BMW 3 Touring (E36) – replacement guide

Free download PDF
1.79 MB
How to change rear strut mount on BMW 3 Touring (E36) – replacement guide

Free download PDF
2.2 MB
How to change rear brake pads on BMW 3 Touring (E36) – replacement guide

Free download PDF
1.86 MB

How to change front anti roll bar links on BMW E90 – replacement guide

Free download PDF
1.15 MB
How to change rear anti roll bar links on BMW E90 – replacement guide

Free download PDF
1.06 MB
How to change front anti roll bar links on BMW E46 – replacement guide

Free download PDF
1.34 MB
How to change rear anti roll bar links on BMW 3 Coupe (E92) – replacement guide

Free download PDF
1.06 MB
How to change front anti roll bar links on BMW E92 – replacement guide

Free download PDF
1.36 MB
How to change rear anti roll bar links on BMW 3 Saloon (E30) – replacement guide

Free download PDF
1.78 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

The most common problems when buying a used car | AUTODOC

4K views

Published on: 10/11/2022
Transform Your Engine Bay: Affordable Valve Cover Restoration with AUTODOC

8K views

Published on: 29/06/2023
#DIY Tips for Fixing Your Car's Air Conditioning Issues | Don't Wait for Costly Repairs!

7K views

Published on: 05/08/2021
5 Essential Tips for beginner drivers: Avoid Common Mistakes

4K views

Published on: 31/01/2023