Recommended replacement interval for the part category Oil filter : 1 year / 20000 km

Important!

This replacement procedure can be used for:
PEUGEOT 308 II 1.6 THP, PEUGEOT 308 II 1.6 THP, PEUGEOT 308 II 1.2 THP, PEUGEOT 308 II 1.6 GT, PEUGEOT 308 II 1.6 GTi (L35GNH), PEUGEOT 308 II 1.6 GTi, PEUGEOT 308 II 1.6 PureTech, PEUGEOT 308 II 1.6 GTi PureTech (L3EGXP) … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Oil filter

Replacement: engine oil and filter – PEUGEOT 308 II. Tools you might need:

                      Combination spanner №7
                    
                      Impact socket №10
                    
                      Impact socket №27
                    
                      HEX bit No.H8.
                    
                      Combination pliers
                    
                      Flat screwdriver
                    
                      Oil drain pan
                    
                      Funnel
                    
                      Torque wrench
                    
                      Microfibre towel
                    
                      Fender cover

Buy tools

Replacement: engine oil and filter – PEUGEOT 308 II. AUTODOC recommends:

Replace the oil filter every time when changing motor oil.
Wear gloves to prevent contact with hot liquid.
All work should be done with the engine stopped.

Replacement: engine oil and filter – PEUGEOT 308 II. Recommended sequence of steps:

Step 1

Open the hood.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3.1

Disconnect the vacuum sensor.

Step 3.2

Squeeze the clamp with combination pliers and disconnect the vacuum valve hose.
Step 4

Unscrew the clamps and disconnect the charger intake hose from the air filter housing.
Step 5

Loosen the binding clamps attaching the air duct to the air filter housing and to the charger. Use a combination spanner #7.
Step 6

Disconnect the crankcase ventilation hose from the air duct.
Step 7

Disconnect the charger intake hose from the air filter housing.
Step 8

Unscrew the clamp and fasteners on the air filter intake pipe. Use a combination spanner #7. Use a drive socket #10.
Step 9

Disconnect the air intake pipe from the air filter housing.
Step 10

Clean the oil filter housing cap.
Step 11

Unscrew the filter housing cap together with the old filter element. Use a drive socket #27.
Step 12

Prepare a container for the old oil filter.
Step 13

Remove the filter element from the filter housing. Put the old filter cartridge in the container.
Step 14

Cover the oil filter housing with a microfibre towel to prevent dirt and foreign objects from getting into the system.
Step 15

Unscrew the oil filler plug.
Step 16

Lift the car using a jack or place it over an inspection pit.

AUTODOC recommends:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.
Step 17

Put a waste oil container with at least 5 l capacity under the drainage hole.
Step 18

Unscrew the drain plug. Use HEX No.H8.
Step 19

Drain the used oil.

Replacement: engine oil and filter – PEUGEOT 308 II. Tip:
Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
Step 20

Clean the area of the oil pan drainage hole.
Step 21

Screw in the new drainage plug and tighten it. Use HEX No.H8. Use a torque wrench. Tighten it to 30 Nm torque.
Step 22

Lower the car.

Step 23

Remove the oil filter cover O-ring. Use a flat screwdriver.
Step 24

Install a new O-ring to its mounting seat on the filter cover.
Step 25

Lubricate the rubber seal of the new filter with a little amount of fresh oil.
Step 26

Remove the microfibre towel from the oil filter housing.
Step 27

Screw the new filter into its place.
Step 28

Screw the cap. Use a torque wrench. Use a drive socket #27. Tighten it to 25 Nm torque.
Step 29

Connect the air intake pipe to the air filter housing.
Step 30

Tighten the clamp and fasteners on the air filter intake pipe. Use a combination spanner #7. Use a drive socket #10.
Step 31

Connect the charger intake hose to the air filter housing.
Step 32

Tighten the binding clamps that attach the air duct to the air filter housing and to the charger. Use a combination spanner #7.
Step 33

Connect the crankcase ventilation hose to the air duct.
Step 34

Connect the vacuum sensor. Squeeze the clamp with combination pliers and connect the vacuum valve hose.
Step 35

Unscrew the oil filler plug. Insert the funnel.
Step 36

Pour oil into the engine through the filler. Required amount of oil: 4.25 l.

Replacement: engine oil and filter – PEUGEOT 308 II. Tip from AUTODOC experts:
Use the oil recommended by the manufacturer.
Step 37

Check the oil level using the dipstick. Top up oil if necessary.

Replacement: engine oil and filter – PEUGEOT 308 II. AUTODOC experts recommend:
The oil level should be between the Min and Max marks.
Step 38

Tighten the oil filler cap.
Step 39

Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine.

Step 40

Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.

AUTODOC recommends:
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 41

Remove the fender protection cover.

Step 42

Close the hood.

Replacement: engine oil and filter – PEUGEOT 308 II. Professionals recommend:
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out. To protect the environment from pollution, be sure to dispose of the used filters at special collection points.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the PEUGEOT 308 II Hatchback model

Peugeot 308 Mk2 tyre size

How to change fuel filter on PEUGEOT 308 II Hatchback – replacement guide

Free download PDF 942.08 KB
How to change air filter on PEUGEOT 308 II Hatchback – replacement guide

Free download PDF 1.33 MB
How to change serpentine belt on PEUGEOT 308 II Hatchback – replacement guide

Free download PDF 1.41 MB
How to change spark plugs on PEUGEOT 308 II Hatchback – replacement guide

Free download PDF 1.17 MB
How to change front windshield wipers on PEUGEOT 308 II Hatchback – replacement guide

Free download PDF 1.46 MB
How to change front anti roll bar links on PEUGEOT 308 II Hatchback – replacement guide

Free download PDF 1.33 MB

How to change engine oil and filter on Peugeot 308 I – replacement guide

Free download PDF 3.3 MB
How to change engine oil and filter on PEUGEOT 308 II SW – replacement guide

Free download PDF 3.15 MB
How to change engine oil and filter on PEUGEOT 308 I SW (4E, 4H) – replacement guide

Free download PDF 3.11 MB
How to change engine oil and filter on PEUGEOT 308 I CC (4B) – replacement guide

Free download PDF 3.1 MB
How to change engine oil and filter on PEUGEOT 308 III Hatchback – replacement guide

Free download PDF 1.58 MB
How to change engine oil and filter on PEUGEOT 308 III SW – replacement guide

Free download PDF 1.58 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

3 essential tips for choosing summer tyres | Get ready for warmer weather

4K views

Published on: 18/05/2023
Fluctuating RPMs? Check these 2 sensors

10K views

Published on: 27/08/2026
TOP 6 WD-40 lifehacks | AUTODOC tips

13K views

Published on: 15/07/2021
DIY car soundproofing | AUTODOC tips

113K views

Published on: 15/04/2021