
Disclaimer
How to change engine oil and filter on NISSAN X-Trail (T32) – replacement guide
downloads:
81
Views:
2682

Recommended replacement interval for the part category Oil filter : 1 year / 20000 km
Important!
This replacement procedure can be used for:
NISSAN X-TRAIL (T32) 2.0 ALL MODE 4x4-i (NT32), NISSAN X-TRAIL (T32) 1.6 DIG-T (T32), NISSAN X-TRAIL (T32) 2.0 (T32), NISSAN X-TRAIL (T32) 2.5 ALL MODE 4x4-i (NT32) … View more
The steps may slightly vary depending on the car design.
NISSAN X-TRAIL (T32) 2.0 ALL MODE 4x4-i (NT32), NISSAN X-TRAIL (T32) 1.6 DIG-T (T32), NISSAN X-TRAIL (T32) 2.0 (T32), NISSAN X-TRAIL (T32) 2.5 ALL MODE 4x4-i (NT32) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for X-TRAIL (T32) and other NISSAN models
Oil filter
Alternative products

Impact socket №19
Impact socket №10
Combination spanner №19
Oil filter cup socket 65/67-14f
Torque wrench
Oil drain pan
Funnel
Flat screwdriver
Replacement: engine oil and filter – NISSAN X-TRAIL (T32). AUTODOC experts recommend:
- Replace the oil filter every time when changing motor oil.
- All work should be done with the engine stopped.
- Wear gloves to prevent contact with hot liquid.
Carry out replacement in the following order:
- Step 1Open the hood.Step 2Remove the oil filler cap.
- Step 3Pour the engine flush in.
- Step 4Install the oil filler cap.
- Step 5Start the engine, let it run for 15 minutes, and then stop it.Step 6Lift the car using a jack or place it over an inspection pit.AUTODOC recommends:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.Step 7Undo the fasteners of the oil pan lower cover.
- Step 8Remove the oil pan cover. Use a drive socket #10. Use a flat screwdriver.
- Step 9Put a waste oil container with at least 5 l capacity under the drainage hole.Step 10Unscrew the drain plug. Use a drive socket no.19 Or ring spanner no.19.
- Step 11Drain the used oil.Replacement: engine oil and filter – NISSAN X-TRAIL (T32). Professionals recommend:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
- Step 12Move the container under the oil filter.Step 13Unscrew the oil filter. Use the 65/67-14f socket.
- Step 14Remove the oil filter. Prepare a container for the old oil filter. Put the old oil filter in the container.AUTODOC recommends:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
- Step 15Clean the oil filter seat.
- Step 16Clean the area of the oil pan drainage hole.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 1
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the NISSAN X-Trail (T32) model
Popular maintenance tutorials for Nissan X-Trail T32
Complete guides for changing the Oil filters on different NISSAN X-TRAIL models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your NISSAN X-TRAIL (T32)
View more
- Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide
- Don’t Replace, Restore: Fixing Damaged Threads at Home
- Why Is the Windscreen Washer Not Spraying? Solution
- How to Order Car Parts Online: Avoid These 5 Common Pitfalls
Most commonly replaced car parts on NISSAN X-TRAIL
Time to replace parts? Get even better deals in our Shop app.

SCAN ME