Disclaimer
How to change engine oil and filter on Nissan X Trail T30 petrol – replacement guide
downloads:
54
Views:
3014
Recommended replacement interval for the part category Oil filter : 15000 km
Important!
This replacement procedure can be used for:
NISSAN X-TRAIL (T30) 2.0 4x4, NISSAN X-TRAIL (T30) 2.0, NISSAN X-TRAIL (T30) 2.0 4x4 … View more
The steps may slightly vary depending on the car design.
NISSAN X-TRAIL (T30) 2.0 4x4, NISSAN X-TRAIL (T30) 2.0, NISSAN X-TRAIL (T30) 2.0 4x4 … View more
The steps may slightly vary depending on the car design.
How to change oil filter and engine oil on NISSAN X TRAIL T30 [TUTORIAL AUTODOC]

All the parts you need to replace – Oil Filter for X-TRAIL (T30) and other NISSAN models
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Drive socket # 14
Oil filter cup socket 65-14F
Ratchet wrench
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – Nissan X Trail T30. AUTODOC experts recommend:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – Nissan X Trail T30 – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Open the hood. - Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Pull up the oil dipstick. - Step 4
Unscrew the oil filler plug. - Step 5
Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – Nissan X Trail T30. Professionals recommend:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point. - Step 6
Put a waste oil container with at least 5 l capacity under the drainage hole. - Step 7
Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray. - Step 8
Unscrew the drain plug. Use a drive socket #14. Use a ratchet wrench. - Step 9
Drain the used oil.Replacement: engine oil and filter – Nissan X Trail T30. Tip from AUTODOC:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole. - Step 10
Clean the oil filter. Use all-purpose cleaning spray. - Step 11
Unscrew the oil filter. Use the 65-14F socket. Use a ratchet wrench. - Step 12
Remove the oil filter. - Step 13
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 14
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 15
Install a new oil filter. - Step 16
Tighten the oil filter. Remember to observe the recommended tightening torque. Use the 65-14F socket. Use a torque wrench. Tighten it to 24 Nm torque. - Step 17
Clean the oil filter. Use all-purpose cleaning spray. - Step 18
Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray. - Step 19
Screw in the new drainage plug and tighten it. Use a drive socket #14. Use a torque wrench. Tighten it to 30 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the NISSAN X-Trail (T30) model
Popular maintenance tutorials for Nissan X Trail t30
Complete guides for changing the Oil filters on different NISSAN X-TRAIL models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your NISSAN X-TRAIL (T30)
View more
Transform Your Car's Look: 6 Simple Accessories You Need to Try!
Deep interior cleaning | Car transformation by detailing
#TPMS Explained: Why Your Light is On and How to Respond Safely
DIY brake caliper restoration | AUTODOC tips
Most commonly replaced car parts on NISSAN X-TRAIL
Time to replace parts? Get even better deals in our Shop app.

SCAN ME

































