
Disclaimer
How to change engine oil and filter on HONDA CR-V IV (RM) – replacement guide
downloads:
8
Views:
104
Recommended replacement interval for the part category Oil filter : 12 month / 15000 km
Important!
This replacement procedure can be used for:
HONDA CR-V IV (RM_) 2.4 AWD (RM4), HONDA CR-V IV (RM_) 2.0 iVtec (RE5, RM1), HONDA CR-V IV (RM_) 2.0 AWD (RE5, RM2), HONDA CR-V IV (RM_) 2.4 (RM3), HONDA CR-V IV (RM_) 2.4 4WD, HONDA CR-V IV (RM_) 2.4 AWD (RM4), HONDA CR-V IV (RM_) 2.4 i-VTEC, HONDA CR-V IV (RM_) 2.4 AWD … View more
The steps may slightly vary depending on the car design.
HONDA CR-V IV (RM_) 2.4 AWD (RM4), HONDA CR-V IV (RM_) 2.0 iVtec (RE5, RM1), HONDA CR-V IV (RM_) 2.0 AWD (RE5, RM2), HONDA CR-V IV (RM_) 2.4 (RM3), HONDA CR-V IV (RM_) 2.4 4WD, HONDA CR-V IV (RM_) 2.4 AWD (RM4), HONDA CR-V IV (RM_) 2.4 i-VTEC, HONDA CR-V IV (RM_) 2.4 AWD … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for CR-V IV (RM_) and other HONDA models
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Drive socket # 17
Oil filter cup socket 65/14-F
Ratchet wrench
Funnel
Oil drain pan
Replacement: engine oil and filter – HONDA CR-V IV (RE). AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Use only new O-rings during installation.
- Please note: all work on the car – HONDA CR-V IV (RE) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – HONDA CR-V IV (RE). AUTODOC experts recommend:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.Unscrew the oil filler plug.Step 2
Put a waste oil container with at least 4 l capacity under the drainage hole. - Step 3
Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray. - Step 4
Unscrew the drain plug. Use a drive socket #17. Use a ratchet wrench. - Step 5
Drain the used oil.AUTODOC recommends:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole. - Step 6
Clean the area of the oil pan drainage hole. - Step 7
Screw in the new drainage plug and tighten it. Use a drive socket #17. Use a torque wrench. Tighten it to 39 nm torque. - Step 8
Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray. - Step 9
Unscrew the oil filter. Use the 65/14-F socket. Use a ratchet wrench. - Step 10Put the old oil filter in the container.Step 11
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 12
Screw the new filter into its place. Use the 65/14-F socket. Observe the recommended tightening torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the HONDA CR-V IV (RM) model
Popular maintenance tutorials for Honda CR-V IV
Complete guides for changing the Oil filters on different HONDA CR-V models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your HONDA CR-V IV (RM_)
View more
5 Essential Tips for beginner drivers: Avoid Common Mistakes
How to repair a bumper yourself | AUTODOC tips
DIY manual gearbox restoration | Drivetrain restoration – Part 3
5 mistakes made when washing the engine | AUTODOC tips
Most commonly replaced car parts on HONDA CR-V
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
































