
Disclaimer
How to change serpentine belt on CITROËN C2 Enterprise (JG) – replacement guide
downloads:
6
Views:
35

Recommended replacement interval for the part category Serpentine belt : 30000 km
Important!
This replacement procedure can be used for:
CITROËN C2 Enterprise (JG_) 1.1 … View more
The steps may slightly vary depending on the car design.
CITROËN C2 Enterprise (JG_) 1.1 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Poly V-Belt for C2 Enterprise (JG_) and other CITROËN models
Serpentine belt
V-Ribbed Belt Set

Wire brush
Torque wrench
Drive socket # 27
HEX bit no.H8
1/4" square drive extension bar
Wheel impact socket #19
Ratchet wrench
Clip removal tool
Phillips screwdriver
Fender cover
Wheel chock
Replacement: serpentine belt – CITROËN C2 ENTERPRISE. Tools you might need:
- All work should be done with the engine stopped.
Replacement: serpentine belt – CITROËN C2 ENTERPRISE. Use the following procedure:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Secure the wheels with chocks.Step 4Loosen the wheel mounting bolts. Use wheel impact socket #19.
- Step 5Raise the car.Replacement: serpentine belt – CITROËN C2 ENTERPRISE. AUTODOC recommends:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 6Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. CITROËN C2 ENTERPRISE
- Step 7Remove the wheel.
- Step 8Unscrew and remove the wheel arch cover fasteners. Use a clip removal tool. Use a Phillips screwdriver.
- Step 9Remove the wheel arch cover.
- Step 10Release the coolant pipe fasteners.
- Step 11Clean the tensioner pulley fastener. Use a wire brush.
- Step 12Loosen the tensioner pulley fastener. Use HEX No.H8. Use a ratchet wrench.
- Step 13Pull aside the V-ribbed belt tensioner pulley. Use a 1/4" square drive extension bar. Use a ratchet wrench.
- Step 14Remove the V-ribbed belt.Replacement: serpentine belt – CITROËN C2 ENTERPRISE. Tip from AUTODOC experts:Check the condition of the tensioner pulley and idler pulley. Replace them if necessary.
- Step 15Install the V-ribbed belt.Replacement: serpentine belt – CITROËN C2 ENTERPRISE. Professionals recommend:Make sure that the V-ribbed belt fits all pulleys snugly.
- Step 16Tension the belt by turning the tensioner pulley clockwise. Use a 1/4" square drive extension bar. Use a ratchet wrench.Replacement: serpentine belt – CITROËN C2 ENTERPRISE. Tip:Keep the belt taut until you've tightened the tensioner pulley fastener.
- Step 17Tighten the fastener of the serpentine belt tensioner pulley. Use HEX No.H8. Use a torque wrench. Tighten it to 35 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the CITROËN C2 Enterprise (JG) model
Popular maintenance tutorials for Citroen C2 Enterprise
Complete guides for changing the Alternator belt on different CITROËN C2 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your CITROËN C2 Enterprise (JG_)
View more
- The most common problems when buying a used car | AUTODOC
- TOP 6 WD-40 lifehacks | AUTODOC tips
- What causes engine misfire? | AUTODOC
- Drive with Care: 8 Common Bad Driving Habits Explained | AUTODOC
Most commonly replaced car parts on CITROËN C2
Time to replace parts? Get even better deals in our Shop app.

SCAN ME