Disclaimer
How to change rear brake shoes on VAUXHALL Tigra Mk I Coupe (S93) – replacement guide
downloads:
2
Views:
15
Recommended replacement interval for the part category Brake Shoe Set : 100000 km
Important!
This replacement procedure can be used for:
VAUXHALL Tigra Mk I Coupe (S93) 1.6 16V, VAUXHALL Tigra Mk I Coupe (S93) 1.4 16V … View more
The steps may slightly vary depending on the car design.
VAUXHALL Tigra Mk I Coupe (S93) 1.6 16V, VAUXHALL Tigra Mk I Coupe (S93) 1.4 16V … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Shoes for Tigra Mk I Coupe (S93) and other VAUXHALL models
Alternative products

Wire brush
All-purpose cleaning spray
Copper grease
Drive socket # 27
Wheel impact socket #17
Torque wrench
Tap wrench
Hammer
Round-nose pliers
Pliers
Flat screwdriver
Wheel chock
Replacement: brake shoes – VAUXHALL TIGRA Mk I (F07). AUTODOC experts recommend:
- Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
- The replacement procedure is identical for all brake pads on the same axle.
- Please note: all work on the car – VAUXHALL TIGRA Mk I (F07) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the bonnet. Unscrew the brake fluid reservoir cap.Step 2Secure the wheels with chocks.Step 3Loosen the wheel mounting bolts. Use wheel impact socket #17.Step 4Raise the rear of the car and secure on supports.Step 5
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VAUXHALL TIGRA Mk I (F07) - Step 6
Remove the wheel. - Step 7Fully lower the parking brake lever.Step 8Clean the brake drum. Use a wire brush. Use all-purpose cleaning spray.Step 9
Remove the hub bearing protection cap. Use a flat screwdriver. Use a hammer.Replacement: brake shoes – VAUXHALL TIGRA Mk I (F07). Tip:Some cars are not equipped with wheel hub caps. - Step 10
Unscrew the wheel hub axle nut. Use a drive socket #27. Use a tap wrench. - Step 11
Remove the brake drum assembled with the wheel hub bearing. - Step 12
Disconnect the parking brake cable from the parking brake lever. Use round-nose pliers. Use a flat screwdriver. - Step 13
Take out brake pad retainer springs from the holes. Use pliers. - Step 14
Remove the brake pads retaining clips. Use pliers. Use round-nose pliers. - Step 15
Remove the brake pads.Replacement: brake shoes – VAUXHALL TIGRA Mk I (F07). AUTODOC experts recommend:Don't press the brake pedal after removing the rear brake drum shoes. This will cause the piston to fall out of the brake cylinder, leakage of brake fluid and depressurization of the system. Examine the brake drum. Replace it if necessary. - Step 16
Remove the brake shoe adjuster. Use round-nose pliers. - Step 17
Insert the brake shoes adjusting mechanism. Use round-nose pliers. - Step 18
Install new brake pads.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VAUXHALL Tigra Mk1 Coupe (S93) model
Popular maintenance tutorials for VAUXHALL TIGRA Mk I (F07)
Complete guides for changing the Brake shoe set on different VAUXHALL TIGRA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VAUXHALL Tigra Mk I Coupe (S93)
View more
The Fast and Easy Way to Fix a Broken Wheel Stud | AUTODOC tips
TOP 5 mistakes during DIY oil change | AUTODOC tips
5 mistakes when replacing consumables
Motorcycle fuel tank restoration
Most commonly replaced car parts on VAUXHALL TIGRA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME



























