Recommended replacement interval for the part category Brake pad set : 30000 km

Important!

This replacement procedure can be used for:
MAZDA 3 (BL) 1.6 MZR CD (BL14), MAZDA 3 (BL) 1.6 MZR (BL14), MAZDA 3 (BL) 2.0 MZR DISI (BLEFW), MAZDA 3 (BL) 2.0 MZR (BLEFW), MAZDA 3 (BL) 1.6 MZ-CD (BL14), MAZDA 3 (BL) 2.2 MZR CD (BL10), MAZDA 3 (BL) 2.2 MZR CD (BL10), MAZDA 3 (BL) 2.3 MPS Turbo (BL14), MAZDA 3 (BL) 2.0 MZR (BLEFW), MAZDA 3 (BL) 2.0 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Brake Pads for 3 (BL) and other MAZDA models

Alternative products

Brake pad set

Replacement: brake pads – MAZDA 3 (BL). Tools you might need:

                      Wire brush
                    
                      Nylon cleaning brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Anti-squeal paste
                    
                      Brake caliper guide pins grease
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      HEX bit no.H7.
                    
                      Wheel impact socket #19
                    
                      Brake caliper wind back tool
                    
                      Ratchet wrench
                    
                      Crow bar
                    
                      Flat Screwdriver
                    
                      Wheel chock

Buy tools

Replacement: brake pads – MAZDA 3 (BL). AUTODOC experts recommend:

Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
The replacement procedure is identical for all brake pads on the same axle.
Please note: all work on the car – MAZDA 3 (BL) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet. Unscrew the brake fluid reservoir cap.

Step 2

Secure the wheels with chocks.
Step 3

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 4

Raise the rear of the car and secure on supports.

Step 5

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. MAZDA 3 (BL)
Step 6

Remove the wheel.
Step 7

Detach the brake caliper retaining spring. Use a flat screwdriver.
Step 8

Remove the dust boot caps of the brake caliper guide pins. Use a flat screwdriver.
Step 9

Unscrew the brake caliper fastening. Use HEX No.H7. Use a ratchet wrench.
Step 10

Remove the guide pins from the brake caliper. Use a flat screwdriver.

Step 11

Spread the brake pads. Use a crowbar.

Step 12

Remove the brake caliper.

Replacement: brake pads – MAZDA 3 (BL). Tip from AUTODOC:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 13

Remove the brake pads.

Replacement: brake pads – MAZDA 3 (BL). Tip from AUTODOC:
Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
Step 14

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

Replacement: brake pads – MAZDA 3 (BL). Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 15

Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.

Replacement: brake pads – MAZDA 3 (BL). Professionals recommend:
Make sure the disc surface is clean before installing the pads.
Step 16

Install new brake pads.

Replacement: brake pads – MAZDA 3 (BL). AUTODOC recommends:
Make sure the pads are installed with linings facing the disc.
Step 17

Treat the brake caliper piston. Use a nylon cleaning brush. Use a brake cleaner.

Replacement: brake pads – MAZDA 3 (BL). Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 18

Press in the brake caliper piston. Use brake caliper wind back tool.
Step 19

Clean the brake caliper guide pins.

Step 20

Treat the brake caliper guide pins. Use the brake caliper guide pin grease.
Step 21

Install the brake caliper and fix it.
Step 22

Screw in the guide pins.

Step 23

Tighten the brake caliper fasteners. Use HEX No.H7. Use a torque wrench. Tighten it to 30 Nm torque.
Step 24

Install the dust boot caps of the brake caliper guide pins.
Step 25

Install the brake caliper retaining spring. Use a flat screwdriver.
Step 26

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 27

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: brake pads – MAZDA 3 (BL). After applying the spray, wait a few minutes.
Step 28

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. MAZDA 3 (BL)
Step 29

Screw in the wheel bolts. Use wheel impact socket #19.
Step 30

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 118 nm torque.
Step 31

Remove the jacks and chocks.

Replacement: brake pads – MAZDA 3 (BL). Professionals recommend:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 32

Tighten the brake fluid reservoir cap. Close the hood.

Replacement: brake pads – MAZDA 3 (BL). Tip from AUTODOC experts:
Without starting the engine, press the brake pedal several times until you feel significant resistance.Slow down smoothly for first 150-200 km after the brake pads replacement. Avoid unneccessary and sharp braking to a stop.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the MAZDA 3 Hatchback (BL) model

Mazda 3 BL tyre size

How to change front brake discs on MAZDA 3 Hatchback (BL) – replacement guide

Free download PDF
2.33 MB
How to change front brake pads on MAZDA 3 Hatchback (BL) – replacement guide

Free download PDF
1.85 MB
How to change rear brake discs on MAZDA 3 Hatchback (BL) – replacement guide

Free download PDF
2.07 MB
How to change rear wheel bearing on MAZDA 3 Hatchback (BL) – replacement guide

Free download PDF
2.23 MB
How to change front windshield wipers on MAZDA 3 Hatchback (BL) – replacement guide

Free download PDF
481.28 KB
How to change front suspension strut on MAZDA 3 Hatchback (BL) – replacement guide

Free download PDF
2.21 MB

How to change front brake pads on MAZDA 3 Hatchback (BL) – replacement guide

Free download PDF
1.85 MB
How to change front brake pads on MAZDA 3 Hatchback (BK) – replacement guide

Free download PDF
1.85 MB
How to change rear brake pads on MAZDA 3 Hatchback (BK) – replacement guide

Free download PDF
1.65 MB
How to change front brake pads on Mazda 3 BK – replacement guide

Free download PDF
2.01 MB
How to change rear brake pads on Mazda 3 BK – replacement guide

Free download PDF
1.81 MB
How to change front brake pads on MAZDA 3 Saloon (BL) – replacement guide

Free download PDF
1.85 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

How to Safely Wash Your Car in Winter Without Damage | AUTODOC tips

3K views

Published on: 31/01/2024
Top 5 possible reasons your car is shaking or vibrating

6K views

Published on: 14/02/2025
Top Automatic Transmission Blunders You Must Dodge | AUTODOC Insights

7K views

Published on: 26/01/2021
Transform Your Car's Look: 6 Simple Accessories You Need to Try!

3K views

Published on: 18/11/2021