How to change rear brake pads on BMW 2 Gran Tourer (F46) – replacement guide
BMW 2 Gran Tourer (F46) 218i, BMW 2 Gran Tourer (F46) 220i, BMW 2 Gran Tourer (F46) 216 d, BMW 2 Gran Tourer (F46) 218 d, BMW 2 Gran Tourer (F46) 220d xDrive, BMW 2 Gran Tourer (F46) 216 i, BMW 2 Gran Tourer (F46) 214 d, BMW 2 Gran Tourer (F46) 220 d, BMW 2 Gran Tourer (F46) 218 d xDrive … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle

- Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
- The replacement procedure is identical for all brake pads on the same axle.
- All work should be done with the engine stopped.
- Step 1
Open the bonnet.
Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3
Remove the wiper arm cover.
- Step 4

Unscrew the brake fluid reservoir cap.
- Step 5

Secure the wheels with chocks.
- Step 6

Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 7
Raise the rear of the car and secure on supports.
Step 8
Unscrew the wheel bolts.
AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. BMW 2 Gran Tourer (F46)
- Step 9

Remove the wheel.
- Step 10

Disconnect the brake pads wear sensor. Use a crowbar.
Please note!Some cars are not equipped with the brake pad wear sensor.
- Step 11

Remove the dust boot caps of the brake caliper guide pins. Use a crowbar.
- Step 12

Unscrew the brake caliper fastening. Use HEX No.H7. Use a ratchet wrench.
- Step 13

Spread the brake pads. Use a crowbar.
- Step 14

Detach the brake caliper retaining spring. Use a crowbar.
- Step 15

Remove the brake caliper.
Replacement: brake pads – BMW 2 Gran Tourer (F46). AUTODOC recommends:Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
- Step 16

Remove the brake pads.
Replacement: brake pads – BMW 2 Gran Tourer (F46). Tip:Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
- Step 17

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
Replacement: brake pads – BMW 2 Gran Tourer (F46). Tip from AUTODOC:After applying the spray, wait a few minutes.
- Step 18

Treat the brake caliper piston. Use a brake cleaner.
AUTODOC recommends:Replacement: brake pads – BMW 2 Gran Tourer (F46). After applying the spray, wait a few minutes.
- Step 19

Press in the brake caliper piston. Use brake caliper wind back tool.
- Step 20

Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.
Replacement: brake pads – BMW 2 Gran Tourer (F46). Professionals recommend:Make sure the disc surface is clean before installing the pads.
Find out which tyre and wheel sizes are compatible with the BMW 2 Gran Tourer (F46) model
Popular maintenance tutorials for BMW F46
Complete guides for changing the Brake pad set on different BMW 2 SERIES models
Track expenses, manage logs, schedule replacements, and more.
Top 10 most useful car life hacks
Discover the 4 Key Reasons Your CHECK ENGINE Light Could Be On | AUTODOC Tips
Don’t Replace, Just Polish! Headlight Restoration with AUTODOC
DIY Mercedes-Benz alternator restoration
Most commonly replaced car parts on BMW 2 SERIES






































