Important!

This replacement procedure can be used for:
BMW Z1 Roadster 2.5 … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Anti-roll bar link

Replacement: anti roll bar links – BMW Z1. List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      Brake cleaner 
                    
                      Copper grease 
                    
                      Torque wrench
                    
                      Combination spanner #13
                    
                      Drive socket # 13
                    
                      Wheel impact socket #17
                    
                      Ratchet wrench
                    
                      Vice
                    
                      Hydraulic transmission jack
                    
                      Crow bar
                    
                      Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on BMW Z1 in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – BMW Z1 – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. BMW Z1
Step 5

Remove the wheel.
Step 6

Treat all joints of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer bar with the control arm. Use a drive socket #13. Use a ratchet wrench.
Step 8

Move the stabiliser bar aside. Use a crowbar.
Step 9

Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 10

Remove the stabilizer rod.

Replacement: anti roll bar links – BMW Z1. AUTODOC recommends:
Examine the stabiliser bushes. Replace them if necessary.
Step 11

Grip the stabiliser link in a vice.

Step 12

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 13

Unscrew the fastener of the stabiliser link bracket. Use a drive socket #13. Use a ratchet wrench.
Step 14

Remove the fastening bolt.
Step 15

Remove the stabiliser link bracket.
Step 16

Release the vice and remove the stabiliser link.

Step 17

Grip a new stabiliser link in a vice.

Step 18

Install the stabiliser link bracket.
Step 19

Install the fastening bolt.
Step 20

Screw in the fastener of the stabiliser link bracket. Use a drive socket #13. Use a ratchet wrench.
Step 21

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 22

Release the vice and remove the stabiliser link.

Step 23

Ιnstall the transverse stabilizer link. Use a crowbar.
Step 24

Reinstall the stabiliser bar in its mounting seat.

Step 25

Screw in the fastener connecting the stabilizer bar to the control arm. Use a drive socket #13. Use a ratchet wrench.
Step 26

Support the arm. Use a hydraulic transmission jack.
Step 27

Tighten the fastener connecting the stabilizer bar with the control arm. Use a drive socket #13. Use a torque wrench. Tighten it to 27 Nm torque.
Step 28

Tighten the fastener of the stabiliser link bracket. Use a combination spanner #13. Use a drive socket #13. Use a torque wrench. Tighten it to 25 Nm torque.
Step 29

Remove the support from under the arm.

AUTODOC recommends:
Replacement: anti roll bar links – BMW Z1. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 30

Treat all joints of the stabiliser link. Use copper grease.
Step 31

Clean the wheel rim mounting seat. Use a wire brush.
Step 32

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 33

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – BMW Z1. After applying the spray, wait a few minutes.
Step 34

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. BMW Z1
Step 35

Screw in the wheel bolts. Use wheel impact socket #17.
Step 36

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.
Step 37

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the BMW Z1 Roadster (E30) model

BMW Z1 E30 tyre size

How to change rear strut mount on BMW Z1 Roadster (E30) – replacement guide

Free download PDF
2.94 MB
How to change rear suspension lower control arm on BMW Z1 Roadster – replacement guide

Free download PDF
1.92 MB
How to change front anti roll bar links on BMW Z1 Roadster – replacement guide

Free download PDF
1.54 MB
How to change rear brake pads on BMW Z1 Roadster – replacement guide

Free download PDF
1.72 MB
How to change front windshield wipers on BMW Z1 Roadster (E30) – replacement guide

Free download PDF
1.43 MB
How to change engine oil and filter on BMW E90 diesel – replacement guide

Free download PDF
2.18 MB

How to change front anti roll bar links on BMW Z1 Roadster – replacement guide

Free download PDF
1.54 MB
How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB
How to change front anti roll bar links on BMW E36 – replacement guide

Free download PDF
1.55 MB
How to change front anti roll bar links on BMW E90 – replacement guide

Free download PDF
1.15 MB
How to change rear anti roll bar links on BMW E36 – replacement guide

Free download PDF
1.74 MB
How to change rear anti roll bar links on BMW E60 – replacement guide

Free download PDF
1.33 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

5 causes of turbocharger failure and how to avoid them

15K views

Published on: 04/04/2024
How to restore a steering wheel | AUTODOC tips

62K views

Published on: 17/02/2022
How to inspect and troubleshoot your car heater when it’s not working

5K views

Published on: 11/02/2021
Cold starts | 5 mistakes that wreck your car

12K views

Published on: 23/10/2025