Disclaimer
How to change front window regulator on SEAT Toledo II Saloon (1M2) – replacement guide
downloads:
6
Views:
112
Important!
This replacement procedure can be used for:
SEAT Toledo II Saloon (1M2) 1.6, SEAT Toledo II Saloon (1M2) 1.8 20V, SEAT Toledo II Saloon (1M2) 2.3 V5, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.4 16V, SEAT Toledo II Saloon (1M2) 1.6 16V, SEAT Toledo II Saloon (1M2) 2.3 V5 20V, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.8 20VT, SEAT Toledo II Saloon (1M2) 1.9 TDI 4Drive … View more
The steps may slightly vary depending on the car design.
SEAT Toledo II Saloon (1M2) 1.6, SEAT Toledo II Saloon (1M2) 1.8 20V, SEAT Toledo II Saloon (1M2) 2.3 V5, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.4 16V, SEAT Toledo II Saloon (1M2) 1.6 16V, SEAT Toledo II Saloon (1M2) 2.3 V5 20V, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.9 TDI, SEAT Toledo II Saloon (1M2) 1.8 20VT, SEAT Toledo II Saloon (1M2) 1.9 TDI 4Drive … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Window Regulator for Toledo II Saloon (1M2) and other SEAT models
Alternative products

Electronic spray
Torque wrench
Drive socket # 8
Drive socket # 10
Torx bit T30
XZN socket bit # 8
Ratchet wrench
Phillips screwdriver
Plastic trim tool
Clip removal tool
Painter's tape
Replacement: window regulator – SEAT TOLEDO II (1M2). Tip from AUTODOC experts:
- All work should be done with the engine stopped.
Replacement: window regulator – SEAT TOLEDO II (1M2). Take the following steps:
- Step 1
Open the car door. - Step 2
Detach the door handle trim panel. Use a plastic trim tool.AUTODOC recommends:Replacement: window regulator – SEAT TOLEDO II (1M2). To avoid damaging the part when removing it, do not use excessive force. - Step 3
Unscrew the door card fasteners. Use a Phillips screwdriver. - Step 4
Detach the door card. Use a plastic trim tool.Replacement: window regulator – SEAT TOLEDO II (1M2). AUTODOC recommends:Do not apply excessive force when removing the part. Otherwise you may damage it. - Step 5
Detach the door lock actuator cable. - Step 6
Detach the bulb connector. - Step 7
Detach the speaker connector. - Step 8
Remove the covers from the window raiser fasteners. Use a plastic trim tool. - Step 9Switch on the ignition.Step 10
Lower the window glass.Replacement: window regulator – SEAT TOLEDO II (1M2). Professionals recommend:Continue lowering the window glass until its fasteners become visible. - Step 11Switch off the ignition.Step 12
Detach the connector for the power window switch module. - Step 13
Unscrew the window glass fasteners. Use a drive socket #10. Use a ratchet wrench.AUTODOC recommends:To avoid injury, hold the glass when unscrewing the fasteners. - Step 14
Raise the window glass all the way up and secure it on the door frame with masking tape.Replacement: window regulator – SEAT TOLEDO II (1M2). Tip from AUTODOC experts:To avoid injury, hold the glass when raising it. - Step 15
Detach the power mirror switch connector. - Step 16
Detach the speaker connector. - Step 17
Detach the power window connector. - Step 18
Detach the power window wiring harness. Use a clip removal tool. - Step 19
Remove the door panel covers. Use a plastic trim tool. - Step 20
Unscrew the door panel fasteners. Use a drive socket #10. Use a ratchet wrench. - Step 21
Unscrew the door lock fasteners. Use XZN #8. Use a ratchet wrench. - Step 22
Remove the door panel together with the window regulator linkage. - Step 23
Detach the door lock connector. - Step 24
Remove the covers from the window raiser fasteners. Use a plastic trim tool. - Step 25Install the covers on the window raiser fasteners.Step 26
Unscrew the fasteners of the power window motor. Use Torx T30. Use a ratchet wrench. - Step 27
Remove the power window motor. - Step 28
Install the power window motor. - Step 29
Screw in the power window motor fasteners. Use Torx T30. Use a ratchet wrench. - Step 30
Unscrew the speaker's fasteners. Use a drive socket #8. Use a ratchet wrench. - Step 31
Remove the speaker. - Step 32
Install the speaker. - Step 33
Screw in the speaker's fasteners. Use a drive socket #8. Use a ratchet wrench. - Step 34
Remove the connector holder. - Step 35
Install the connector holder on the new door panel. - Step 36
Install the door panel together with the window regulator linkage. - Step 37
Treat the door lock connector. Use dielectric grease. - Step 38
Attach the door lock connector. - Step 39
Screw in the door panel fasteners. Use a drive socket #10. Use a ratchet wrench.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Toledo II Saloon (1M2) model
Popular maintenance tutorials for Seat Toledo 1m
Complete guides for changing the Window mechanism on different SEAT TOLEDO models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Toledo II Saloon (1M2)
View more
TOP 5 mistakes when replacing shock absorbers | AUTODOC tips
#DIY guide: Changing your car's color with a spray can | AUTODOC tips
Initial Car Inspection: What to Check Before You Buy
Motorcycle fuel tank restoration
Most commonly replaced car parts on SEAT TOLEDO
Time to replace parts? Get even better deals in our Shop app.

SCAN ME





































