Important!

This replacement procedure can be used for:
VW Golf Alltrack VII (BA5, BV5) 1.6 TDI 4motion, VW Golf Alltrack VII (BA5, BV5) 2.0 TDI 4motion, VW Golf Alltrack VII (BA5, BV5) 2.0 TDI 4motion, VW Golf Alltrack VII (BA5, BV5) 1.8 TSI 4motion … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Strut Mount for Golf Alltrack VII (BA5, BV5) and other VW models

Top strut mount

        Top strut mount for Golf VII Alltrack (BA5, BV5) Diesel (110 hp)
      
        Top strut mount for Golf VII Alltrack (BA5, BV5) Diesel (150 hp)
      
        Top strut mount for Golf VII Alltrack (BA5, BV5) Diesel (184 hp)
      
        Top strut mount for Golf VII Alltrack (BA5, BV5) Petrol (180 hp)

Replacement: strut mount – VW GOLF ALLTRACK (BA5). List of the tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Ceramic grease
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Combination spanner #18
                      
                        Drive socket # 13
                      
                        Drive socket # 16
                      
                        Drive socket # 18
                      
                        12-point socket # 24
                      
                        21-mm strut nut socket
                      
                        Shock absorber socket
                      
                        HEX bit no.H7
                      
                        XZN bit # 6
                      
                        XZN bit # 14
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Tap wrench
                      
                        Hydraulic strut spring compressor
                      
                        Crow bar
                      
                        Hydraulic transmission jack
                      
                        Fender cover
                      
                        Wheel chock

Buy tools

Replacement: strut mount – VW GOLF ALLTRACK (BA5). Tip from AUTODOC:

The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
All mounts of the front shock struts should be replaced simultaneously.
Please note: all work on the car – VW GOLF ALLTRACK (BA5) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Open the bonnet.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Remove the cowl grille seal.
Step 4

Remove the clips of the plastic cowl grille. Use a crowbar.
Step 5

Move the cowl grille aside to access the fasteners of the suspension strut mount.
Step 6

Clean the fasteners of the shock strut upper mount. Use a wire brush. Use WD-40 spray.
Step 7

Loosen the upper fasteners of the suspension strut. Use a drive socket #13. Use a ratchet wrench.
Step 8

Secure the wheels with chocks.

Step 9

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 10

Raise the car.

Replacement: strut mount – VW GOLF ALLTRACK (BA5). Tip from AUTODOC experts:
If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.
Step 11

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. VW GOLF ALLTRACK (BA5)
Step 12

Remove the wheel.
Step 13

Clean the fastener that connects the sway bar link to the suspension strut. Use a wire brush. Use WD-40 spray.
Step 14

Unscrew the fastener connecting the stabilizer link to the shock strut. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench.
Step 15

Remove the stabilizer rod.
Step 16

Clean the lower fastener connecting the suspension strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 17

Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a drive socket #18. Use XZN #14. Use a ratchet wrench.
Step 18

Unscrew the fastener connecting the drive shaft to the wheel hub. Use 12-point socket No.24. Use a tap wrench.
Step 19

Remove the fastening bolt.

Step 20

Clean the fasteners connecting the ball joint to the suspension control arm. Use a wire brush. Use WD-40 spray.
Step 21

Unscrew the fasteners connecting the ball joint to the control arm. Use a drive socket #16. Use a ratchet wrench.
Step 22

Disconnect the ball joint from the control arm.
Step 23

Prop up the steering knuckle. Use a hydraulic transmission jack.

Step 24

Detach the driveshaft from the steering knuckle.

Replacement: strut mount – VW GOLF ALLTRACK (BA5). Tip:
Make sure that the drive shaft is not unloaded (when the car is jacked).
Step 25

Remove the fastening bolt.
Step 26

Release the lower fastener connecting the shock strut to the steering knuckle. Use a special drive socket to remove the shock absorber.
Step 27

Disconnect the steering knuckle from the shock absorber strut.
Step 28

Unscrew the upper fasteners of the shock strut.

AUTODOC recommends:
VW GOLF ALLTRACK (BA5) – To avoid injury, hold the suspension strut while unscrewing the fastening bolts.
Step 29

Remove the suspension strut.
Step 30

Set the suspension strut on the spring compressor tool.

Replacement: strut mount – VW GOLF ALLTRACK (BA5). Professionals recommend:
Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
Step 31

Compress the spring.
Step 32

Clean the strut piston rod. Use a wire brush. Use WD-40 spray.
Step 33

Remove the strut piston rod nut. Use a 21-mm strut nut socket. Use HEX No.H7. Use a ratchet wrench.
Step 34

Remove the upper strut mount together with the bump stop.
Step 35

Remove the bump stop from the old suspension strut mount and install it on the new one.
Step 36

Install the upper strut mount together with the bump stop.
Step 37

Tighten the shock strut piston rod nut. Use a 21-mm strut nut socket. Use HEX No.H7. Use a torque wrench. Tighten it to 60 Nm torque.
Step 38

Decompress the spring.
Step 39

Treat the shock strut rod. Use copper grease.
Step 40

Remove the assembled shock strut.
Step 41

Clean the suspension strut mounting seat on the steering knuckle. Clean the splines of the drive shaft CV joint. Clean the CV axle mounting seat. Clean the ball joint mounting seat. Clean the mounting seats of the shock strut. Use a wire brush. Use WD-40 spray.
Step 42

Install the shock strut into the wheel arch.

Replacement: strut mount – VW GOLF ALLTRACK (BA5). Tip from AUTODOC experts:
Make sure that the suspension strut is installed in the correct position, according to the markings.
Step 43

Secure the upper fasteners of the shock strut. Do not tighten it.

AUTODOC recommends:
Important! Hold the suspension strut while screwing in the fastening bolts. VW GOLF ALLTRACK (BA5)
Step 44

Fix the shock absorber strut on the steering knuckle.
Step 45

Install the fastening bolt.
Step 46

Remove the support from under the steering knuckle.

AUTODOC recommends:
Replacement: strut mount – VW GOLF ALLTRACK (BA5). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 47

Install the drive shaft.
Step 48

Attach the ball joint to the control arm.
Step 49

Tighten the fasteners that connect the ball joint to the suspension arm. Use a drive socket #16. Use a ratchet wrench.
Step 50

Screw in the fastener that connects the shock strut to the steering knuckle. Use a drive socket #18. Use XZN #14. Use a ratchet wrench.
Step 51

Install and tighten the drive shaft bolt. Use 12-point socket No.24. Use a ratchet wrench.
Step 52

Clean the sway bar link fastener.
Step 53

Ιnstall the transverse stabilizer link.
Step 54

Screw in the fastener connecting the sway bar link to the suspension strut. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench.
Step 55

Prop up the steering knuckle. Use a hydraulic transmission jack.
Step 56

Tighten the bolt connecting the drive shaft to the wheel hub. Use 12-point socket No.24. Use a torque wrench. Tighten it to 200 Nm torque.
Step 57

Remove the support from under the steering knuckle.

AUTODOC recommends:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 58

Tighten the lower fasteners of the suspension strut. Use a drive socket #18. Use XZN #14. Use a torque wrench. Tighten it to 70 Nm torque.+90°
Step 59

Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #18. Use XZN #6. Use a torque wrench. Tighten it to 65 Nm torque.
Step 60

Tighten the fasteners connecting the ball joint to the control arm. Use a drive socket #16. Use a torque wrench. Tighten it to 40 Nm torque.+45°
Step 61

Treat the fastener that connects the sway bar link to the suspension strut. Treat the fastener that connects the suspension strut to the steering knuckle. Treat the ball joint fastener. Use copper grease.
Step 62

Clean the wheel rim mounting seat. Use a wire brush.
Step 63

Treat the surface where the brake disc contacts the wheel rim. Use ceramic grease.
Step 64

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: strut mount – VW GOLF ALLTRACK (BA5). After applying the spray, wait a few minutes.
Step 65

Install the wheel.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while screwing in the fastening bolts on the car. VW GOLF ALLTRACK (BA5)
Step 66

Screw in the wheel bolts. Use wheel impact socket #17.
Step 67

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.
Step 68

Remove the jacks and chocks.
Step 69

Tighten the upper fasteners of the shock strut. Use a drive socket #13. Use a torque wrench. Tighten it to 15 Nm torque.+90°
Step 70

Treat the fasteners of the shock strut mount. Use copper grease.
Step 71

Install and secure the cowl grille.
Step 72

Install the cowl grille seal.

Step 73

Remove the fender protection cover.

Step 74

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the VW Golf VII Alltrack (BA5, BV5) model.

Browse tyres

How to change track rod end on VW Golf Alltrack (BA5, BV5) – replacement guide

Free download PDF
2.21 MB
How to change front anti roll bar links on VW Golf Alltrack (BA5, BV5) – replacement guide

Free download PDF
2.05 MB
How to change front wheel bearing on VW Golf Alltrack VII (BA5, BV5) – replacement guide

Free download PDF
2.49 MB
How to change front brake pads on VW Golf Alltrack VII (BA5, BV5) – replacement guide

Free download PDF
1.57 MB
How to change rear brake pads on VW Golf Alltrack VII (BA5, BV5) – replacement guide

Free download PDF
1.46 MB
How to change rear brake discs on VW Golf Alltrack VII (BA5, BV5) – replacement guide

Free download PDF
1.64 MB

How to change rear strut mount on VW Golf 7 – replacement guide

Free download PDF
2.75 MB
How to change front strut mount on VW Golf 7 – replacement guide

Free download PDF
3.7 MB
How to change front strut mount on VW Golf 5 – replacement guide

Free download PDF
3.07 MB
How to change rear strut mount on VW Golf 6 – replacement guide

Free download PDF
2.68 MB
How to change front strut mount on VW Golf 6 – replacement guide

Free download PDF
4.01 MB
How to change front strut mount on VW Golf 4 – replacement guide

Free download PDF
1.85 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to wash your car in winter | AUTODOC tips

3K views

Published on: 31/01/2024
What to do if your car heater isn't working | AUTODOC tips

4K views

Published on: 11/02/2021
5 car tips for a winter's day | AUTODOC tips

5K views

Published on: 05/02/2024
Top 5 mistakes when replacing spark plugs | AUTODOC tips

9K views

Published on: 13/07/2023