Disclaimer
How to change front anti roll bar links on SEAT Leon ST (5F8) – replacement guide
downloads:
0
Views:
1
Important!
This replacement procedure can be used for:
SEAT Leon ST (5F8) 1.4 TSI, SEAT Leon ST (5F8) 2.0 TDI, SEAT Leon ST (5F8) 2.0 TDI, SEAT Leon ST (5F8) 1.8 TSI, SEAT Leon ST (5F8) 2.0 TDI, SEAT Leon ST (5F8) 1.2 TSI, SEAT Leon ST (5F8) 1.2 TSI, SEAT Leon ST (5F8) 1.4 TSI, SEAT Leon ST (5F8) 1.6 TDI, SEAT Leon ST (5F8) 1.6 TDI, SEAT Leon ST (5F8) 2.0 TDI, SEAT Leon ST (5F8) 1.6 TDI, SEAT Leon ST (5F8) 1.4 TGI, SEAT Leon ST (5F8) 1.6 TDI 4Drive, SEAT Leon ST (5F8) 2.0 TDI 4Drive, SEAT Leon ST (5F8) 1.2 TSI, SEAT Leon ST (5F8) 1.4 TSI, SEAT Leon ST (5F8) 1.4 TSI, SEAT Leon ST (5F8) 1.6 TDI 4Drive, SEAT Leon ST (5F8) 2.0 TDI 4Drive, SEAT Leon ST (5F8) 1.8 TSI 4Drive, SEAT Leon ST (5F8) 2.0 Cupra, SEAT Leon ST (5F8) 2.0 Cupra, SEAT Leon ST (5F8) 1.0 TSI, SEAT Leon ST (5F8) 2.0 Cupra, SEAT Leon ST (5F8) 1.6 TDI, SEAT Leon ST (5F8) 2.0 Cupra, SEAT Leon ST (5F8) 2.0 Cupra 4Drive, SEAT Leon ST (5F8) 1.6 SRE … View more
The steps may slightly vary depending on the car design.
SEAT Leon ST (5F8) 1.4 TSI, SEAT Leon ST (5F8) 2.0 TDI, SEAT Leon ST (5F8) 2.0 TDI, SEAT Leon ST (5F8) 1.8 TSI, SEAT Leon ST (5F8) 2.0 TDI, SEAT Leon ST (5F8) 1.2 TSI, SEAT Leon ST (5F8) 1.2 TSI, SEAT Leon ST (5F8) 1.4 TSI, SEAT Leon ST (5F8) 1.6 TDI, SEAT Leon ST (5F8) 1.6 TDI, SEAT Leon ST (5F8) 2.0 TDI, SEAT Leon ST (5F8) 1.6 TDI, SEAT Leon ST (5F8) 1.4 TGI, SEAT Leon ST (5F8) 1.6 TDI 4Drive, SEAT Leon ST (5F8) 2.0 TDI 4Drive, SEAT Leon ST (5F8) 1.2 TSI, SEAT Leon ST (5F8) 1.4 TSI, SEAT Leon ST (5F8) 1.4 TSI, SEAT Leon ST (5F8) 1.6 TDI 4Drive, SEAT Leon ST (5F8) 2.0 TDI 4Drive, SEAT Leon ST (5F8) 1.8 TSI 4Drive, SEAT Leon ST (5F8) 2.0 Cupra, SEAT Leon ST (5F8) 2.0 Cupra, SEAT Leon ST (5F8) 1.0 TSI, SEAT Leon ST (5F8) 2.0 Cupra, SEAT Leon ST (5F8) 1.6 TDI, SEAT Leon ST (5F8) 2.0 Cupra, SEAT Leon ST (5F8) 2.0 Cupra 4Drive, SEAT Leon ST (5F8) 1.6 SRE … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for Leon ST (5F8) and other SEAT models
Anti-roll bar link
Anti-roll bar link
Anti-roll bar link for Leon III ST (5F8) Petrol (86 hp)
Anti-roll bar link for Leon III ST (5F8) Petrol (122 hp)
Anti-roll bar link for Leon III ST (5F8) Diesel (90 hp)
Wire brush
WD-40 spray
Brake cleaner
Ceramic grease
Copper grease
Torque wrench
Combination spanner #18
Combination spanner #19
Drive socket # 18
Drive socket # 19
XZN socket bit #6
HEX bit No.H5
Wheel impact socket #17
Ratchet wrench
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on SEAT LEON ST (5F8) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – SEAT LEON ST (5F8) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the car.Replacement: anti roll bar links – SEAT LEON ST (5F8). Professionals recommend:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. SEAT LEON ST (5F8) - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #18. Use XZN #6. Use a ratchet wrench. - Step 8
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench. - Step 9
Remove the stabiliser link.Replacement: anti roll bar links – SEAT LEON ST (5F8). Tip from AUTODOC experts:Examine stabiliser bushes. Replace them if needed. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Install a new stabiliser link and tighten the fasteners. Use a combination spanner #19. Use HEX No.H5. Use a ratchet wrench. - Step 12
Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #19. Use a torque wrench. Tighten it to 65 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Leon III ST (5F8) model.
Popular maintenance tutorials for Seat Leon 5f8
Free download PDF
1.39 MB
Free download PDF3.41 MB
Free download PDF2.79 MB
Free download PDF1.37 MB
Free download PDF1.58 MB
Free download PDF2.26 MB
Complete guides for changing the Drop links on different SEAT LEON models
Free download PDF1.15 MB
Free download PDF1.19 MB
Free download PDF1.42 MB
Free download PDF634.88 KB
Free download PDF1.15 MB
Free download PDF1.15 MB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your SEAT Leon ST (5F8)
View more
Top 5 brake repair mistakes | AUTODOC tips
Headlight Restoration | AUTODOC tips
Top 5 mistakes when working in the engine bay | AUTODOC tips
Coolant comparison test | AUTODOC
