Disclaimer
How to change engine oil and filter on RENAULT Logan Pickup (US_) – replacement guide
downloads:
1
Views:
9
Recommended replacement interval for the part category Oil filter : 12 month / 15000 km
Important!
This replacement procedure can be used for:
RENAULT Logan Pickup (US_) 1.6 16V (US1Y) … View more
The steps may slightly vary depending on the car design.
RENAULT Logan Pickup (US_) 1.6 16V (US1Y) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for Logan Pickup (US_) and other RENAULT models
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Square oil drain plug socket No.8
Oil filter cup socket #74-15F
Oil filter cup socket #76-12F
Ratchet wrench
Funnel
Fender cover
Replacement: engine oil and filter – RENAULT Logan Pickup (US_). AUTODOC experts recommend:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – RENAULT Logan Pickup (US_) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Pull up the oil dipstick. - Step 4
Unscrew the oil filler plug. - Step 5Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – RENAULT Logan Pickup (US_). AUTODOC experts recommend:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.Step 6
Put a waste oil container with at least 5 l capacity under the drainage hole. - Step 7Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.Step 8
Unscrew the drain plug. Use square oil drain plug socket No.8 Use a ratchet wrench. - Step 9
Drain the used oil.Replacement: engine oil and filter – RENAULT Logan Pickup (US_). Tip:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole. - Step 10
Unscrew the oil filter. Use the 76/12-F socket. Use a ratchet wrench. - Step 11
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 12
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 13
Screw the new filter into its place. Use the 74/15-F socket. Use a torque wrench. Tighten it to 20 nm torque. - Step 14
Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray. - Step 15
Screw in the new drainage plug and tighten it. Use square oil drain plug socket No.8 Use a torque wrench. Tighten it to 28 nm torque. - Step 16
Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the RENAULT Logan Pickup (US_) model
Popular maintenance tutorials for RENAULT Logan Pickup (US_)
Complete guides for changing the Oil filters on different RENAULT LOGAN models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your RENAULT Logan Pickup (US_)
View more
How to Make a DIY Foam Sprayer | AUTODOC tips
How to prevent car windows from fogging up | AUTODOC tips
3 essential tips for choosing summer tyres | Get ready for warmer weather
Top 5 reasons why the suspension knocks | AUTODOC tips
Most commonly replaced car parts on RENAULT LOGAN
Time to replace parts? Get even better deals in our Shop app.

SCAN ME




























