Disclaimer
How to change engine oil and filter on MAZDA 3 Box Body / Hatchback (BM) – replacement guide
downloads:
4
Views:
126
Recommended replacement interval for the part category Oil filter : 12 month / 15000 km
Important!
This replacement procedure can be used for:
MAZDA 3 Box Body / Hatchback (BM) 1.5 … View more
The steps may slightly vary depending on the car design.
MAZDA 3 Box Body / Hatchback (BM) 1.5 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for 3 Box Body / Hatchback (BM) and other MAZDA models
Alternative products

All-purpose cleaning spray
Drive socket # 19
Oil filter cup socket 65/14F
Ratchet wrench
Torque wrench
Funnel
Oil drain pan
Fender cover
Replacement: engine oil and filter – MAZDA 3 Kasten / Schrägheck (BM). AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – MAZDA 3 Kasten / Schrägheck (BM) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – MAZDA 3 Kasten / Schrägheck (BM). AUTODOC experts recommend:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped. - Step 2
Put a waste oil container with at least 5 l capacity under the drainage hole. - Step 3
Unscrew the drain plug. Use a drive socket #19. Use a ratchet wrench. - Step 4
Drain the used oil.Replacement: engine oil and filter – MAZDA 3 Kasten / Schrägheck (BM). Professionals recommend:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole. - Step 5
Clean the area of the oil pan drainage hole. - Step 6
Screw in the new drainage plug and tighten it. Use a drive socket #19. Use a torque wrench. Tighten it to 28 nm torque. - Step 7Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.Step 8
Unscrew the oil filter. Use the 65/14F socket. Use a ratchet wrench. - Step 9
Put the old oil filter in the container. - Step 10Clean the oil filter seat.Step 11
Screw the new filter into its place. Use the 65/14F socket. Use a ratchet wrench. - Step 12
Lower the car.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the MAZDA 3 Box Body / Hatchback (BM) model
Popular maintenance tutorials for MAZDA 3 Kasten / Schrägheck (BM)
Complete guides for changing the Oil filters on different MAZDA 3 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your MAZDA 3 Box Body / Hatchback (BM)
View more
Top 4 Car Cleaning Products to Protect Your Car's Body | AUTODOC Tips
How to remove scratches from car plastic | AUTODOC tips
Revive Your Tyres: Expert Tips for a Lasting Shine | AUTODOC Guide
What to do if the ABS light comes on: DIY Diagnostics Tips
Most commonly replaced car parts on MAZDA 3
Time to replace parts? Get even better deals in our Shop app.

SCAN ME

























