Disclaimer
How to change engine oil and filter on INFINITI G Convertible – replacement guide
downloads:
1
Views:
6
Recommended replacement interval for the part category Oil filter : 12 month / 15000 km
Important!
This replacement procedure can be used for:
INFINITI G Convertible 37, INFINITI G Convertible 37 … View more
The steps may slightly vary depending on the car design.
INFINITI G Convertible 37, INFINITI G Convertible 37 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for G Convertible and other INFINITI models
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Drive socket # 14
Oil filter cup socket 65-14F
Ratchet wrench
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – INFINITI G Convertible. AUTODOC experts recommend:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – INFINITI G Convertible – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Pull up the oil dipstick. - Step 4
Unscrew the oil filler plug. - Step 5Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – INFINITI G Convertible. Professionals recommend:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.Step 6
Put a waste oil container with at least 5 l capacity under the drainage hole. - Step 7
Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray. - Step 8
Unscrew the drain plug. Use a drive socket #14. Use a ratchet wrench. - Step 9
Drain the used oil.Replacement: engine oil and filter – INFINITI G Convertible. Tip from AUTODOC:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole. - Step 10
Clean the oil filter. Use all-purpose cleaning spray. - Step 11
Unscrew the oil filter. Use the 65-14F socket. Use a ratchet wrench. - Step 12
Remove the oil filter. - Step 13
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 14
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 15
Install a new oil filter. - Step 16
Tighten the oil filter. Remember to observe the recommended tightening torque. Use the 65-14F socket. Use a torque wrench. Tighten it to 24 Nm torque. - Step 17
Clean the oil filter. Use all-purpose cleaning spray. - Step 18
Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray. - Step 19
Screw in the new drainage plug and tighten it. Use a drive socket #14. Use a torque wrench. Tighten it to 30 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the INFINITI G Convertible (V36) model
Popular maintenance tutorials for INFINITI G Convertible
Complete guides for changing the Oil filters on different INFINITI G models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your INFINITI G Convertible
View more
Drive with Care: 8 Common Bad Driving Habits Explained | AUTODOC
Cold starts | 5 mistakes that wreck your car
Why does it burn oil? The main cause of oil consumption in EA888 Gen 1
Extend your engine's life: Avoid these 3 damaging factors | AUTODOC tips
Most commonly replaced car parts on INFINITI G
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
























