Disclaimer
How to change engine oil and filter on Citroen C1 1 PM PN – replacement guide
downloads:
19
Views:
787
Recommended replacement interval for the part category Oil filter : 1 year / 15000 km
Important!
This replacement procedure can be used for:
CITROËN C1 II (PA_, PS_) 1.0 VTi, CITROËN C1 II (PA_, PS_) 1.0 VTi … View more
The steps may slightly vary depending on the car design.
CITROËN C1 II (PA_, PS_) 1.0 VTi, CITROËN C1 II (PA_, PS_) 1.0 VTi … View more
The steps may slightly vary depending on the car design.
How to change oil filter and engine oil on CITROËN C1 (PM, PN) [TUTORIAL AUTODOC]

All the parts you need to replace – Oil Filter for C1 (PM_, PN_) and other CITROËN models
Alternative products

All-purpose cleaning spray
Drive socket # 14
Oil filter cup socket 67-14F
Ratchet wrench
Torque wrench
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – Citroen C1 1 PM PN. Tip from AUTODOC experts:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – Citroen C1 1 PM PN – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Open the hood. - Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car. - Step 3
Unscrew the oil filler plug. - Step 4
Lift the car using a jack or place it over an inspection pit.Replacement: engine oil and filter – Citroen C1 1 PM PN. Tip from AUTODOC:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point. - Step 5
Put a waste oil container with at least 4 l capacity under the drainage hole. - Step 6
Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray. - Step 7
Unscrew the drain plug. Use a drive socket #14. Use a ratchet wrench. - Step 8
Drain the used oil.Replacement: engine oil and filter – Citroen C1 1 PM PN. AUTODOC experts recommend:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole. - Step 9Prepare a container for the old oil filter.Step 10
Unscrew the oil filter. Use the 67-14F socket. Use a ratchet wrench. - Step 11Put the old oil filter in the container.Replacement: engine oil and filter – Citroen C1 1 PM PN. Tip:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.Step 12
Clean the oil filter seat. Use all-purpose cleaning spray. - Step 13
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 14
Screw the new filter into its place. Use the 67-14F socket. Use a torque wrench. Tighten it to 23 Nm torque. - Step 15
Clean the area of the oil pan drainage hole. - Step 16
Screw in the new drainage plug and tighten it. Use a drive socket #14. Use a torque wrench. Tighten it to 27 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the CITROËN C1 I model
Popular maintenance tutorials for Citroen C1 Mk1
Complete guides for changing the Oil filters on different CITROËN C1 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your CITROËN C1 (PM_, PN_)
View more
How to Use Sandblasting Equipment: Step-by-Step Guide | AUTODOC Tips
Revive Your Vehicle's Look | How to Restore Wheel Rims Yourself!
Top 5 mistakes when replacing spark plugs | AUTODOC tips
5 signs of a faulty strut mount and how to fix it
Most commonly replaced car parts on CITROËN C1
Time to replace parts? Get even better deals in our Shop app.

SCAN ME

































