Disclaimer
How to change engine oil and filter on BMW Z4 Roadster (E85) – replacement guide
downloads:
50
Views:
1279
Recommended replacement interval for the part category Oil filter : 12 month / 15000 km
Important!
This replacement procedure can be used for:
BMW Z4 Roadster (E85) 2.2i, BMW Z4 Roadster (E85) 2.5i, BMW Z4 Roadster (E85) 3.0i … View more
The steps may slightly vary depending on the car design.
BMW Z4 Roadster (E85) 2.2i, BMW Z4 Roadster (E85) 2.5i, BMW Z4 Roadster (E85) 3.0i … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for Z4 Roadster (E85) and other BMW models
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Drive socket # 19
Drive socket # 36
Flat screwdriver
Ratchet wrench
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – BMW Z4 (E85). AUTODOC experts recommend:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – BMW Z4 (E85) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Unscrew the oil filler plug. - Step 4
Pull up the oil dipstick. - Step 5
Clean the oil filter housing cap. Use all-purpose cleaning spray. - Step 6
Unscrew the filter housing cap together with the old filter element. Use a drive socket #36. Use a ratchet wrench. - Step 7
Put the old oil filter in the container. - Step 8Lift the car using a jack or place it over an inspection pit.Step 9
Put a waste oil container with at least 7 l capacity under the drainage hole. - Step 10
Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray. - Step 11
Unscrew the drain plug. Use a drive socket #19. Use a ratchet wrench. - Step 12
Drain the used oil.Replacement: engine oil and filter – BMW Z4 (E85). Tip:Caution! The oil may be hot. - Step 13
Remove the oil filter cover O-ring. Use a flat screwdriver. - Step 14
Clean the oil filter housing cap. Use all-purpose cleaning spray. - Step 15
Install a new O-ring to its mounting seat on the filter cover. - Step 16
Install the new oil filter to the mounting seat on the filter cover. - Step 17
Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray. - Step 18
Screw in the new drainage plug and tighten it. Use a drive socket #19. Use a torque wrench. Tighten it to 25 Nm torque. - Step 19
Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the BMW Z4 Roadster (E85) model
Popular maintenance tutorials for BMW Z4 E85
Complete guides for changing the Oil filters on different BMW Z4 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your BMW Z4 Roadster (E85)
View more
Why Checking Your Oil is Crucial for Engine Performance
How to easily repair a punctured tyre | AUTODOC tips
How to make an injector test bench yourself
Extend your engine's life: Avoid these 3 damaging factors | AUTODOC tips
Most commonly replaced car parts on BMW Z4
Time to replace parts? Get even better deals in our Shop app.

SCAN ME






























