
Disclaimer
How to change front strut mount on SEAT Ibiza IV ST (6J8, 6P8) – replacement guide
downloads:
3
Views:
114
Important!
This replacement procedure can be used for:
SEAT Ibiza IV ST (6J8, 6P8) 1.2 TDI, SEAT Ibiza IV ST (6J8, 6P8) 1.2 TSI, SEAT Ibiza IV ST (6J8, 6P8) 1.2, SEAT Ibiza IV ST (6J8, 6P8) 1.2, SEAT Ibiza IV ST (6J8, 6P8) 1.4, SEAT Ibiza IV ST (6J8, 6P8) 1.6 TDI, SEAT Ibiza IV ST (6J8, 6P8) 1.6 TDI … View more
The steps may slightly vary depending on the car design.
SEAT Ibiza IV ST (6J8, 6P8) 1.2 TDI, SEAT Ibiza IV ST (6J8, 6P8) 1.2 TSI, SEAT Ibiza IV ST (6J8, 6P8) 1.2, SEAT Ibiza IV ST (6J8, 6P8) 1.2, SEAT Ibiza IV ST (6J8, 6P8) 1.4, SEAT Ibiza IV ST (6J8, 6P8) 1.6 TDI, SEAT Ibiza IV ST (6J8, 6P8) 1.6 TDI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Strut Mount for Ibiza IV ST (6J8, 6P8) and other SEAT models
Top strut mount
Alternative products

Wire brush
WD-40 spray
Drive socket # 13
Drive socket # 18
Flare nut socket №22
HEX bit No.H6.
12-point socket 1-3/16”
Shock absorber socket
Combination spanner #18
Combination spanner #21
Ratchet wrench
Torque wrench
Copper grease
Wheel impact socket #17
Hydraulic transmission jack
Rubber mallet
Hydraulic strut spring compressor
Wheel chock
Fender cover
Replacement: strut mount – SEAT IBIZA V ST (6J8, 6P8). Tip from AUTODOC experts:
- The replacement procedure is identical for the mounts of the left and right shock struts of the front suspension.
- Be sure to replace all self-locking nuts and bolts during installation.
- Warning! Shut down the engine before starting any work – SEAT IBIZA V ST (6J8, 6P8).
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2Open the bonnet.Step 3Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 4Remove the wheel rim cover.
- Step 5Unscrew the hub lock nut. Use 1-3/16" drive 12-point socket.Replacement: strut mount – SEAT IBIZA V ST (6J8, 6P8). Tip from AUTODOC:Do not unscrew the fastener by more than 90 degrees.
- Step 6Loosen the wheel mounting bolts. Use wheel impact socket #17.
- Step 7Raise the front of the car and secure on supports.Step 8Unscrew the wheel bolts.Replacement: strut mount – SEAT IBIZA V ST (6J8, 6P8). AUTODOC recommends:To avoid injury, hold up the wheel when unscrewing the bolts.
- Step 9Remove the wheel.Step 10Disconnect the wiring and the brake hose from the bracket on the shock strut.
- Step 11Unscrew the fastener connecting the drive shaft to the wheel hub. Use 1-3/16" drive 12-point socket.
- Step 12Clean the fasteners connecting the shock strut to the steering knuckle. Clean the fasteners connecting the ball joint to the suspension control arm. Use a wire brush. Use WD-40 spray.
- Step 13Unscrew the fastener connecting the ball joint to the suspension control arm. Use a drive socket #13.
- Step 14Disconnect the spherical joint from the arm.Step 15Pull the drive shaft out of the steering knuckle and lifting it, tie to the body.AUTODOC recommends:Make sure that the drive shaft is not unloaded (when the car is jacked).
- Step 16Prop up the steering knuckle. Use a hydraulic transmission jack.
- Step 17Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #18. Use a drive socket #18. Use a ratchet wrench.
- Step 18Remove the support from under the steering knuckle.
- Step 19Release the lower fastener connecting the shock strut to the steering knuckle. Use a special drive socket to remove the shock absorber.
- Step 20Disconnect the steering knuckle from the shock absorber strut.Replacement: strut mount – SEAT IBIZA V ST (6J8, 6P8). AUTODOC recommends:If necessary, use a rubber mallet.
- Step 21Prop up the steering knuckle. Use a hydraulic transmission jack.Replacement: strut mount – SEAT IBIZA V ST (6J8, 6P8). Tip:Make sure that the steering knuckle is not released from load.
- Step 22Unscrew the upper fastening of the shock absorber strut. Use a combination spanner #21. Use HEX No.H6.AUTODOC recommends:Important! Hold the suspension strut while unscrewing the fastening bolts. SEAT IBIZA V ST (6J8, 6P8)
- Step 23Remove the suspension strut. Set the shock absorber strut on the spring compressor tool.Replacement: strut mount – SEAT IBIZA V ST (6J8, 6P8). Professionals recommend:Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
- Step 24Compress the spring.
- Step 25Remove the strut piston rod nut. Use flare nut socket #22. Use HEX No.H6.
- Step 26Remove the shock strut mount.
- Step 27Clean the mounting seat of the shock strut mount. Use a wire brush.Step 28Install a new strut mount.
- Step 29Tighten the shock strut piston rod nut. Use flare nut socket #22. Use HEX No.H6. Use a torque wrench. Tighten it to 60 Nm torque.Replacement: strut mount – SEAT IBIZA V ST (6J8, 6P8). AUTODOC experts recommend:Check to make sure the spring is positioned correctly. Avoid its misalignment.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the SEAT Ibiza IV ST (6J8, 6P8) model
Popular maintenance tutorials for Seat Ibiza 6j Estate
Complete guides for changing the Strut mount on different SEAT IBIZA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your SEAT Ibiza IV ST (6J8, 6P8)
View more
- How to fix your car with AUTODOC CLUB
- How do EGR valves work? | AUTODOC
- DIY car soundproofing | AUTODOC tips
- 5 possible reasons why your car heater isn't working
Most commonly replaced car parts on SEAT IBIZA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME