
Disclaimer
How to change engine oil and filter on CITROËN C5 X III – replacement guide
downloads:
3
Views:
65

Recommended replacement interval for the part category Oil filter : 12 month / 15000 km
Important!
This replacement procedure can be used for:
CITROËN C5 X III Hybrid (NDDGYP) … View more
The steps may slightly vary depending on the car design.
CITROËN C5 X III Hybrid (NDDGYP) … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Oil Filter for C5 X III and other CITROËN models
Oil filter
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Drive socket # 27
HEX bit No.H6.
Ratchet wrench
Oil drain pan
Funnel
Flat Screwdriver
Fender cover
Replacement: engine oil and filter – CITROËN C5 X III. Tip from AUTODOC:
- Replace the oil filter every time when changing motor oil.
- Use only new O-rings during installation.
- Wear gloves to prevent contact with hot liquid.
- Warning! Shut down the engine before starting any work – CITROËN C5 X III
Carry out replacement in the following order:
- Step 1Open the hood.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3Unscrew the oil filler plug.
- Step 4Lift the car using a jack or place it over an inspection pit.AUTODOC recommends:The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.Step 5Put a waste oil container with at least 4 l capacity under the drainage hole.
- Step 6Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray.
- Step 7Unscrew the drain plug. Use HEX No.H6. Use a ratchet wrench.
- Step 8Drain the used oil.Replacement: engine oil and filter – CITROËN C5 X III. Tip:Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
- Step 9Clean the oil filter housing cap. Use all-purpose cleaning spray.
- Step 10Unscrew the filter housing cap together with the old filter element. Use a drive socket #27. Use a ratchet wrench.
- Step 11Prepare a container for the old oil filter.Step 12Put the old oil filter in the container.AUTODOC recommends:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
- Step 13Detach the oil filter from the filter cover.
- Step 14Remove the oil filter cover O-ring. Use a flat screwdriver.
- Step 15Clean the oil filter housing cap. Use all-purpose cleaning spray.
- Step 16Install a new O-ring to its mounting seat on the filter cover.
- Step 17Install the new oil filter to the mounting seat on the filter cover.Please note!Make sure to install the filter correctly. Don't mix up the sides of the part.
- Step 18Lubricate the rubber seal of the new filter with a little amount of fresh oil.
- Step 19Install a new oil filter housing cover and tighten it. Use a drive socket #27. Use a torque wrench. Tighten it to 25 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the CITROËN C5 X III model
Popular maintenance tutorials for CITROËN C5 X III
Complete guides for changing the Oil filters on different CITROËN C5 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your CITROËN C5 X III
View more
- Deep interior cleaning | Car transformation by detailing
- How to easily repair a punctured tyre | AUTODOC tips
- Revive Your Tyres: Expert Tips for a Lasting Shine | AUTODOC Guide
- Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide
Most commonly replaced car parts on CITROËN C5
Time to replace parts? Get even better deals in our Shop app.

SCAN ME