Important!
This replacement procedure can be used for:
NISSAN MICRA II (K11) 1.0 i 16V, NISSAN MICRA II (K11) 1.5 D, NISSAN MICRA II (K11) 1.0 i 16V, NISSAN MICRA II (K11) 1.4 i 16V View more

The steps may slightly vary depending on the car design.

How to change front wheel bearing on NISSAN MICRA 2 Hatchback [TUTORIAL AUTODOC]

video
All the parts you need to replace – Wheel Bearing for MICRA II (K11) and other NISSAN models
How to change Wheel bearing kit on Nissan Micra K11 1.0 i 16V – step-by-step instructions for straightforward car repair
Wheel bearing kit
How to change Wheel bearing on Nissan Micra K11 1.0 i 16V – step-by-step instructions for straightforward car repair
Wheel bearing
Tools
Replacement: wheel bearing – Nissan Micra K11. List of the tools you'll need:
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Multipurpose grease
Drive socket # 17
12-point socket # 32
Combination spanner #17
Combination spanner #19
Wheel impact socket #19
Ratchet wrench
Torque wrench
Bush and bearing driver set
Flat Screwdriver
Circlip pliers
Hammer
Rubber mallet
Ball joint puller
Wheel chock
AUTODOC recommends:
  • Do not re-use the bearing assembly of your Nissan Micra K11 car.
  • The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
  • Please note: all work on the car – Nissan Micra K11 – should be done with the engine switched off.
Carry out replacement in the following order:
  1. Step 1
    How to change Wheel Bearing on Nissan Micra K11 1992 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 2
    How to replace NISSAN MICRA II (K11) 1.0 i 16V 1993 Wheel Bearing - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #19.
  3. Step 3
    Nissan Micra K11 1.3 i 16V 1994 Wheel Bearing replacement: free workshop manuals
    Raise the front of the car and secure on supports.
  4. Step 4
    Changing Wheel Bearing on NISSAN MICRA II (K11) 1.5 D 1995 by yourself
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Nissan Micra K11
  5. Step 5
    How to remove NISSAN MICRA 1.0 1996 Wheel Bearing - online easy-to-follow instructions
    Remove the wheel.
  6. Step 6
    Clean the fastener of the driveshaft. Use a wire brush. Use WD-40 spray.
    Step 7
    How to replace Wheel Bearing on NISSAN MICRA II (K11) 1997: download PDF manuals and video instructions
    Unscrew the fastener connecting the drive shaft to the wheel hub. Use 12-point socket No.32. Use a ratchet wrench.
  7. Step 8
    Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
    Step 9
    How hard is it to do yourself: Wheel Bearing replacement on Nissan Micra K11 1.0 i 16V 1998 - download illustrated guide
    Unscrew the caliper bracket fastening. Use a drive socket #17. Use a ratchet wrench.
  8. Step 10
    Need to know how to renew Wheel Bearing on NISSAN MICRA 1999? This free workshop manual will help you to do it yourself
    Remove the brake caliper together with its bracket.
    Replacement: wheel bearing – Nissan Micra K11. Tip from AUTODOC:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
  9. Step 11
    Changing of Wheel Bearing on Nissan Micra K11 2000 won't be an issue if you follow this illustrated step-by-step guide
    Remove the brake disc.
  10. Step 12
    Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
    Step 13
    NISSAN MICRA 1.4 i 16V Wheel Bearing replacement: online guides and video tutorials
    Unscrew the end fastening nut to the steering knuckle. Use a drive socket #17. Use a ratchet wrench.
  11. Step 14
    Disconnect the tie rod end from the steering knuckle.
    Step 15
    Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.
    Step 16
    Replacing Wheel Bearing on Nissan Micra K11 2002 1.0 i 16V by yourself
    Unscrew the ball joint fastening to the steering knuckle. Use a combination spanner #19.
  12. Step 17
    MICRA II (K11) 1.0 2003 Wheel Bearing DIY replacement workshop manual
    Disconnect the ball joint from the steering knuckle. Use a ball joint puller.
  13. Step 18
    Clean the fasteners connecting the shock strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
    Step 19
    How to change Wheel Bearing on NISSAN MICRA II (K11) 2004 - tips and tricks
    Unscrew the lower fastener connecting the shock strut to the steering knuckle. Use a combination spanner #17. Use a drive socket #17. Use a ratchet wrench.
  14. Step 20
    Step-by-step recommendations for DIY replacement Nissan Micra K11 2005 1.0 Wheel Bearing
    Remove the fastening bolts (2 pieces).
  15. Step 21
    Disconnect the steering knuckle from the shock absorber strut.
    Step 22
    Detach the driveshaft from the steering knuckle.
    Replacement: wheel bearing – Nissan Micra K11. AUTODOC experts recommend:
    Make sure that the drive shaft is not unloaded (when the car is jacked).
    Step 23
    DIY replacement of Wheel Bearing on NISSAN MICRA II (K11) 1.4 i 16V 2006 is not an issue anymore with our step-by-step tutorial
    Remove the steering knuckle together with the hub.
  16. Step 24
    How to change Wheel Bearing on Nissan Micra K11 1992 - free PDF and video manuals
    Remove the inner wheel bearing oil seal. Use a flat screwdriver.
  17. Step 25
    How to replace NISSAN MICRA II (K11) 1.0 i 16V 1993 Wheel Bearing - step-by-step manuals and video guides
    Remove the wheel hub from the steering knuckle. Use a bush and bearing driver set. Use a hammer.
  18. Step 26
    Remove the inner wheel bearing oil seal. Use a flat screwdriver.
    Step 27
    Remove the retaining ring from the steering knuckle. Use circlip pliers.
    Step 28
    Nissan Micra K11 1.3 i 16V 1994 Wheel Bearing replacement: free workshop manuals
    Press out the wheel hub bearing. Use a bush and bearing driver set.
  19. Step 29
    Changing Wheel Bearing on NISSAN MICRA II (K11) 1.5 D 1995 by yourself
    Clean the hub bearing mounting seat. Use a wire brush. Use WD-40 spray.
  20. Step 30
    How to remove NISSAN MICRA 1.0 1996 Wheel Bearing - online easy-to-follow instructions
    Press the new bearing in the steering knuckle. Use a bush and bearing driver set.
    Replacement: wheel bearing – Nissan Micra K11. Tip from AUTODOC experts:
    Check to make sure the wheel hub bearing is positioned correctly. Avoid its misalignment. Stop pressing on the surface of the bearing immediately after it has been fitted into its mounting seat.
  21. Step 31
    How to replace Wheel Bearing on NISSAN MICRA II (K11) 1997: download PDF manuals and video instructions
    Install the retaining ring in the steering knuckle. Use circlip pliers.
  22. Step 32
    Apply special grease to the bearing assembly mounting seat. Use a multipurpose grease.
    Step 33
    How hard is it to do yourself: Wheel Bearing replacement on Nissan Micra K11 1.0 i 16V 1998 - download illustrated guide
    Press in the inner wheel bearing oil seal. Use a rubber mallet. Use a bush and bearing driver set. Use a hammer.
  23. Step 34
    Need to know how to renew Wheel Bearing on NISSAN MICRA 1999? This free workshop manual will help you to do it yourself
    Install the wheel hub on the steering knuckle. Use a bush and bearing driver set.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
NISSAN MICRA II (K11) Wheel Bearing replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY NISSAN MICRA II (K11) Wheel Bearing replacement - online guide
Tips & tricks for your NISSAN MICRA II (K11)
View more
  • How to change Wheel bearings on NISSAN MICRA II (K11) 1.4 i 16V - replacement tricks
    How to save when buying car parts
  • Changing Hub bearing Nissan Micra K11 1.0 i 16V - Replacement Tips
    How to prevent car windows from fogging up | AUTODOC tips
  • Maintenance Hacks - NISSAN MICRA II (K11) 1.3 i 16V Wheel bearing kit replacement guide
    TOP 4 car cleaning products | AUTODOC tips
  • Replace Wheel hub bearing on Nissan Micra K11 - free video tips
    3 things that cause engine damage | AUTODOC tips