How to change engine oil and filter on Mercedes W168 petrol – replacement guide
downloads:
24
Views:
498
0
Users voted – 0
Recommended replacement interval for the part category Oil filter : 12month / 15000km
Important!
This replacement procedure can be used for:
MERCEDES-BENZ A-Class (W168) A 210 (168.035, 168.135),
MERCEDES-BENZ A-Class (W168) A 190 (168.032, 168.132),
MERCEDES-BENZ A-Class (W168) A 140 (168.031, 168.131),
MERCEDES-BENZ A-Class (W168) A 140 (168.031, 168.131)
…
View more
The steps may slightly vary depending on the car design.
How to change engine oil and oil filter on MERCEDES-BENZ A W168 TUTORIAL | AUTODOC
All the parts you need to replace – Oil Filter for A-Class (W168) and other MERCEDES-BENZ models
Replace the oil filter every time when changing motor oil.
Wear gloves to prevent contact with hot liquid.
Use only new O-rings during installation.
Replacement: engine oil and filter – Mercedes W168. Use the following procedure:
Carry out replacement in the following order:
Step 1
Lift the car using a jack or place it over an inspection pit.
Replacement: engine oil and filter – Mercedes W168. Tip:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.All work should be done with the engine stopped.
Step 2
Put a waste oil container with at least 5 l capacity under the drainage hole.
Step 3
Unscrew the drain plug. Use a drive socket #13. Use a ratchet wrench.
Step 4
Drain the used oil.
Replacement: engine oil and filter – Mercedes W168. AUTODOC recommends:
Caution! The oil may be hot.Wait until the oil has completely drained from the drainage hole.
Step 5
Clean the area of the oil pan drainage hole.
Step 6
Screw in the new drainage plug and tighten it. Use a drive socket #13. Use a torque wrench. Tighten it to 30 nm torque.
Step 7
Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 8
Lower the car.
Step 9
Open the hood.
Step 10
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 11
Unscrew the filter housing cap together with the old filter element. Use a drive socket #27. Use a ratchet wrench.
Step 12
Prepare a container for the old oil filter.
Step 13
Put the old oil filter in the container.
Replacement: engine oil and filter – Mercedes W168. Professionals recommend:
Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
Step 14
Detach the oil filter from the filter cover.
Step 15.1
Remove old o-rings from the oil filter cover.
Step 15.2
Use a flat screwdriver.
Step 16
Install new O-rings (2 pieces) and a new oil filter to their mounting seats on the filter cover. Use a flat screwdriver.
Please note!
Make sure to install the filter correctly. Don't mix up the sides of the part.
Step 17
Lubricate the rubber seal of the new filter with a little amount of fresh oil.
Step 18
Clean the oil filter seat.
Step 19.1
Install a new oil filter housing cover and tighten it.
Step 19.2
Use a drive socket #27. Use a torque wrench. Tighten it to 25 Nm torque.
Step 20
Unscrew the oil filler plug.
Step 21
Remove the oil filler cap.
Step 22
Insert the funnel.
Step 23
Pour oil into the engine through the filler. Required amount of oil: 4.5 L.
Replacement: engine oil and filter – Mercedes W168. Tip:
Use the oil recommended by the manufacturer.
Step 24
Check the oil level using the dipstick. Top up oil if necessary.
Please note!
The oil level should be between the Min and Max marks.
Step 25
Install the oil filler cap.
Step 26
Tighten the oil filler cap.
Step 27
Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine.
Step 28
Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.
Please note!
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 29
Remove the fender protection cover. Close the hood.
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out.To protect the environment from pollution, be sure to dispose of the used filters at special collection points.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the MERCEDES-BENZ A-Class (W168) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your MERCEDES-BENZ A-Class (W168)
View more
Top 5 mistakes when replacing spark plugs | AUTODOC tips
How to fix your car with AUTODOC CLUB
What to check when buying a used car | AUTODOC tips
How to unlock your car without a key | AUTODOC tips
Most commonly replaced car parts on MERCEDES-BENZ A-CLASS