Important!
This replacement procedure can be used for:
FIAT BRAVO II (198) 1.6 D Multijet

The steps may slightly vary depending on the car design.

How to replace front springs / front coil springs on FIAT BRAVO 2 (198) [TUTORIAL AUTODOC]

Required tools:
Required tools:
Wire brush
WD-40 spray
Copper grease
HEX bit No.H6.
Combination spanner #15
Combination spanner #17
Combination spanner #19
Drive socket # 15
Drive socket # 17
Drive socket # 19
Wheel impact socket #17
Ratchet wrench
Torque wrench
Tap wrench
Crow bar
Hydraulic strut spring compressor
Hydraulic transmission jack
Fender cover
Wheel chock
AUTODOC recommends:
  • Both coil springs of the front suspension should be replaced simultaneously.
  • The replacement procedure is identical for the left and right coil springs of the front suspension.
  • All work should be done with the engine stopped.
Carry out replacement in the following order:
  1. How to change Springs on FIAT BRAVO II (198) 2006 - free PDF and video manuals
    Step 1
    Open the bonnet.
  2. How to replace FIAT BRAVO II (198) 1.9 D Multijet 2007 Springs - step-by-step manuals and video guides
    Step 2
    Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
  3. FIAT BRAVO II (198) 1.6 D Multijet 2008 Springs replacement: free workshop manuals
    Step 3
    Clean the fasteners of the shock strut upper mount. Use a wire brush.Use WD-40 spray.
  4. Changing Springs on FIAT BRAVO II (198) 1.4 T-Jet 2009 by yourself
    Step 4
    Remove the rubber strip.
  5. How to remove FIAT BRAVA 1.4 LPG 2010 Springs - online easy-to-follow instructions
    Step 5
    Loosen the upper fastener of the shock strut mount.Use a combination spanner #19.
  6. How to replace Springs on FIAT BRAVO II (198) 2011: download PDF manuals and video instructions
    Step 6
    Secure the wheels with chocks.
  7. How hard is it to do yourself: Springs replacement on FIAT BRAVO II (198) 1.9 D Multijet 2012 - download illustrated guide
    Step 7
    Loosen the wheel mounting bolts.Use wheel impact socket #17.
  8. Need to know how to renew Springs on FIAT BRAVA ? This free workshop manual will help you to do it yourself
    Step 8
    Raise the front of the car and secure on supports.
  9. Changing of Springs on FIAT BRAVO II (198) 2014 won't be an issue if you follow this illustrated step-by-step guide
    Step 9
    Unscrew the wheel bolts.
    AUTODOC recommends:
    To avoid injury, hold up the wheel when unscrewing the bolts.
  10. FIAT BRAVA 1.4 Springs replacement: online guides and video tutorials
    Step 10
    Remove the wheel.
  11. Replacing Springs on FIAT BRAVO II (198) 2016 1.9 D Multijet by yourself
    Step 11
    Disconnect the wiring and the brake hose from the bracket on the shock strut.Use a crowbar.
  12. BRAVO II (198) 1.4 LPG 2017 Springs DIY replacement workshop manual
    How to change Springs on FIAT BRAVO II (198) 2018 - tips and tricks
    Step 12.1
    Clean the fasteners connecting the stabiliser link to the shock strut, and those connecting the shock strut to the steering knuckle.
    Step 12.2
    Use a wire brush.Use WD-40 spray.
  13. Step-by-step recommendations for DIY replacement FIAT BRAVO II (198) 2019 1.4 LPG Springs
    Step 13
    Unscrew the nut and remove the stabilizer rod from the shock strut.Use a combination spanner #17.Use a ratchet wrench.
  14. DIY replacement of Springs on FIAT BRAVO II (198) 1.4 2020 is not an issue anymore with our step-by-step tutorial
    Step 14
    Prop up the steering knuckle.Use a hydraulic transmission jack.
  15. How to change Springs on FIAT BRAVO II (198) 2006 - free PDF and video manuals
    Step 15
    Unscrew the lower fastener connecting the shock strut to the steering knuckle.Use a combination spanner #15.Use a drive socket #17.Use a tap wrench.
  16. How to replace FIAT BRAVO II (198) 1.9 D Multijet 2007 Springs - step-by-step manuals and video guides
    Step 16
    Remove the fastening bolts.
  17. FIAT BRAVO II (198) 1.6 D Multijet 2008 Springs replacement: free workshop manuals
    Step 17
    Disconnect the steering knuckle from the shock absorber strut.
  18. Changing Springs on FIAT BRAVO II (198) 1.4 T-Jet 2009 by yourself
    Step 18
    Unscrew the top fastening of the shock strut mount.Use a drive socket #19.Use a ratchet wrench.
    AUTODOC recommends:
    To avoid injuries, hold the shock strut when undoing the fastening bolts.
  19. How to remove FIAT BRAVA 1.4 LPG 2010 Springs - online easy-to-follow instructions
    Step 19
    Remove the suspension strut.
  20. How to replace Springs on FIAT BRAVO II (198) 2011: download PDF manuals and video instructions
    Step 20
    Set the shock absorber strut on the spring compressor tool.
    AUTODOC recommends:
    Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
  21. How hard is it to do yourself: Springs replacement on FIAT BRAVO II (198) 1.9 D Multijet 2012 - download illustrated guide
    Step 21
    Compress the spring.
  22. Need to know how to renew Springs on FIAT BRAVA ? This free workshop manual will help you to do it yourself
    Step 22
    Treat the shock strut rod.Use a wire brush.Use WD-40 spray.
  23. Changing of Springs on FIAT BRAVO II (198) 2014 won't be an issue if you follow this illustrated step-by-step guide
    Step 23
    Remove the strut piston rod nut.Use a combination spanner #19.Use HEX No.H6.Use a ratchet wrench.
  24. FIAT BRAVA 1.4 Springs replacement: online guides and video tutorials
    Step 24
    Remove the top strut mount.
  25. Replacing Springs on FIAT BRAVO II (198) 2016 1.9 D Multijet by yourself
    Step 25
    Release the coil spring.
  26. BRAVO II (198) 1.4 LPG 2017 Springs DIY replacement workshop manual
    Step 26
    Remove the spring.
    AUTODOC recommends:
    Τhoroughly examine the shock absorber mount, dust boot, bump stop. Replace them if necessary.
  27. How to change Springs on FIAT BRAVO II (198) 2018 - tips and tricks
    Step 27
    Install the spring on the shock absorber.
  28. Step-by-step recommendations for DIY replacement FIAT BRAVO II (198) 2019 1.4 LPG Springs
    Step 28
    Compress the spring.
  29. DIY replacement of Springs on FIAT BRAVO II (198) 1.4 2020 is not an issue anymore with our step-by-step tutorial
    Step 29
    Install the upper strut mount and the strut mount bearing.
  30. How to change Springs on FIAT BRAVO II (198) 2006 - free PDF and video manuals
    Step 30
    Tighten the shock strut piston rod nut. Use a combination spanner #19.Use HEX No.H6.Use a torque wrench.Tighten it to 60 Nm torque.
    AUTODOC recommends:
    Check to make sure the spring is positioned correctly. Avoid its misalignment.
  31. How to replace FIAT BRAVO II (198) 1.9 D Multijet 2007 Springs - step-by-step manuals and video guides
    Step 31
    Decompress the spring.
  32. FIAT BRAVO II (198) 1.6 D Multijet 2008 Springs replacement: free workshop manuals
    Step 32
    Remove the assembled shock strut.
  33. Changing Springs on FIAT BRAVO II (198) 1.4 T-Jet 2009 by yourself
    Step 33
    Install the shock strut into the wheel arch.
  34. How to remove FIAT BRAVA 1.4 LPG 2010 Springs - online easy-to-follow instructions
    Step 34
    Screw the top fastening of the shock strut mountDo not tighten it.
    AUTODOC recommends:
    To avoid injuries, hold the shock strut when screwing the fastening bolts in.
  35. How to replace Springs on FIAT BRAVO II (198) 2011: download PDF manuals and video instructions
    Step 35
    Treat the shock strut mounting seat on the steering knuckle.Use a wire brush.Use WD-40 spray.
  36. How hard is it to do yourself: Springs replacement on FIAT BRAVO II (198) 1.9 D Multijet 2012 - download illustrated guide
    Step 36
    Fix the shock absorber strut on the steering knuckle.
  37. Need to know how to renew Springs on FIAT BRAVA ? This free workshop manual will help you to do it yourself
    Step 37
    Raise the hydraulic transmission jack by 10-15 cm.
  38. Changing of Springs on FIAT BRAVO II (198) 2014 won't be an issue if you follow this illustrated step-by-step guide
    Step 38
    Install the fastening bolts.
  39. FIAT BRAVA 1.4 Springs replacement: online guides and video tutorials
    Step 39
    Tighten the lower fasteners connecting the shock strut to the steering knuckle.Use a drive socket #15.Use a drive socket #17.Use a combination spanner #15.Use a torque wrench.Tighten it to 80 Nm torque.
  40. Replacing Springs on FIAT BRAVO II (198) 2016 1.9 D Multijet by yourself
    Step 40
    Treat all joints of the stabiliser link.Use WD-40 spray.
  41. BRAVO II (198) 1.4 LPG 2017 Springs DIY replacement workshop manual
    Step 41
    Ιnstall the transverse stabilizer link.
  42. How to change Springs on FIAT BRAVO II (198) 2018 - tips and tricks
    Step 42
    Tighten the fastener connecting the stabilizer link to the shock strut.Use a combination spanner #17.Use a torque wrench.Tighten it to 55 Nm torque.
  43. Step-by-step recommendations for DIY replacement FIAT BRAVO II (198) 2019 1.4 LPG Springs
    Step 43
    Remove the support from under the steering knuckle.
    AUTODOC recommends:
    Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
  44. DIY replacement of Springs on FIAT BRAVO II (198) 1.4 2020 is not an issue anymore with our step-by-step tutorial
    Step 44
    Connect the fastener of the ABS sensor cable to the shock absorber strut.Fasten the brake hose on the strut.
  45. How to change Springs on FIAT BRAVO II (198) 2006 - free PDF and video manuals
    Step 45
    Clean the wheel rim mounting seat. Use a wire brush.Treat the contacting surface.Use copper grease.
    Step 46
    Install the wheel.
    AUTODOC recommends:
    To avoid injury, hold up the wheel when screwing in the fastening bolts.
  46. How to replace FIAT BRAVO II (198) 1.9 D Multijet 2007 Springs - step-by-step manuals and video guides
    Step 47
    Screw in the wheel bolts.Use wheel impact socket #17.
  47. FIAT BRAVO II (198) 1.6 D Multijet 2008 Springs replacement: free workshop manuals
    Step 48
    Lower the car and working in a cross order, tighten the wheel bolts.Use a torque wrench.Tighten it to 120 Nm torque.
  48. Changing Springs on FIAT BRAVO II (198) 1.4 T-Jet 2009 by yourself
    Step 49
    Tighten the upper fastener of the shock absorber strut mount.Use a drive socket #19.Use a torque wrench.Tighten it to 51 Nm torque.
  49. How to remove FIAT BRAVA 1.4 LPG 2010 Springs - online easy-to-follow instructions
    Step 50
    Install the rubber strip.
  50. How to replace Springs on FIAT BRAVO II (198) 2011: download PDF manuals and video instructions
    Step 51
    Treat the fasteners of the shock strut mount.Use copper grease.
  51. How hard is it to do yourself: Springs replacement on FIAT BRAVO II (198) 1.9 D Multijet 2012 - download illustrated guide
    Step 52
    Remove the fender protection cover.
  52. Need to know how to renew Springs on FIAT BRAVA ? This free workshop manual will help you to do it yourself
    Step 53
    Close the hood.
  53. Changing of Springs on FIAT BRAVO II (198) 2014 won't be an issue if you follow this illustrated step-by-step guide
    Step 54
    Remove the jacks and chocks.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Vehicle maintenance log book
Know what, when and how to repair, and manage your car expenses
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Google Play AUTODOC Club App
App Store AUTODOC Club App
FIAT BRAVO II (198) Springs replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY FIAT BRAVO II (198) Springs replacement - online guide
Tips & tricks for your FIAT BRAVO II (198)
View more
  • How to change Suspension springs on FIAT BRAVO II (198) 1.4 - replacement tricks
    How to choose the right dash cam for your car | AUTODOC
  • Changing Coil springs FIAT BRAVO II (198) 1.9 D Multijet - Replacement Tips
    What to do if your check engine light is on | Tips from AUTODOC
  • Maintenance Hacks - FIAT BRAVO II (198) 1.6 D Multijet Suspension springs replacement guide
    Basic rules for driving all types of transmissions | AUTODOC
  • Replace Coil springs on FIAT BRAVO II (198) - free video tips
    Types and features of run-flat tyres | AUTODOC