Replacement: brake discs – Peugeot 206 CC 2D. AUTODOC recommends:
Replace the brake disks on the car Peugeot 206 CC 2D in complete set for each axis. Regardless of the state of components. This will ensure even braking.
The replacement procedure is identical for both brake disks on the same axle.
When changing the brake discs, always replace the brake pads.
All work should be done with the engine stopped.
Replacement: brake discs – Peugeot 206 CC 2D. Recommended sequence of steps:
Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2
Secure the wheels with chocks.
Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 4
Raise the front of the car and secure on supports.
Step 5
Unscrew the wheel bolts.
AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. Peugeot 206 CC 2D
Step 6
Remove the wheel.
Step 7
Spread the brake pads. Use a crowbar.
Step 8
Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 9
Unscrew the brake caliper fastening. Use a drive socket #13. Use a ratchet wrench.
Step 10
Remove the brake caliper.
Replacement: brake discs – Peugeot 206 CC 2D. Tip from AUTODOC experts:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 11
Remove the brake pads.
Step 12
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 13
Unscrew the caliper bracket fastening. Use a drive socket #19. Use a ratchet wrench. Use a tap wrench.
Step 14
Remove the caliper bracket.
Step 15
Unscrew the brake disc fastening. Use Torx T30. Use an impact screwdriver.
Step 16
Remove the brake disc.
Step 17
Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 18
Install the brake disc.
Step 19
Tighten the brake disc fastening. Use Torx T30. Use a torque wrench. Tighten it to 9 Nm torque.
Step 20
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake discs – Peugeot 206 CC 2D. After applying the spray, wait a few minutes.
Step 21
Install the brake caliper bracket.
Step 22
Tighten the brake caliper bracket. Use a drive socket #19. Use a torque wrench. Tighten it to 105 Nm torque.
Step 23
Treat the brake caliper piston. Use a brake cleaner.
Replacement: brake discs – Peugeot 206 CC 2D. Tip:
After applying the spray, wait a few minutes.
Step 24
Press in the brake caliper piston. Use brake caliper wind back tool.
Step 25
Install the brake pads.
Step 26
Install the brake caliper and fix it. Use a drive socket #13. Use a torque wrench. Tighten it to 30 Nm torque.
Step 27
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 28
Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake discs – Peugeot 206 CC 2D. After applying the spray, wait a few minutes.
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 30
Screw in the wheel bolts. Use wheel impact socket #19.
Step 31
Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 100 Nm torque.
Step 32
Remove the jacks and chocks.
AUTODOC recommends:
Peugeot 206 CC 2D – Without starting the engine, press the brake pedal several times until it feels firm.Check the brake fluid level in the expansion tank and refill if necessary.
Step 33
Tighten the brake fluid reservoir cap. Close the hood.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Searching for the right tyres?
Find out which tyre and wheel sizes are compatible with the PEUGEOT 206 CC (2D) model.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your PEUGEOT 206 CC (2D)
View more
How do EGR valves work? | AUTODOC
How to reduce fuel consumption | AUTODOC
5 most common causes of oil leaks | AUTODOC tips
Top 5 reasons why the suspension knocks | AUTODOC tips