Important!

This replacement procedure can be used for:
VAUXHALL Vivaro Van (X82) 1.6 CDTi, VAUXHALL Vivaro Van (X82) 1.6 CDTi, VAUXHALL Vivaro Van (X82) 1.6 CDTi, VAUXHALL Vivaro Van (X82) 1.6 CDTi, VAUXHALL Vivaro Van (X82) 1.6 CDTi, VAUXHALL Vivaro Van (X82) 1.6 CDTi, VAUXHALL Vivaro Van (X82) 1.6 CDTi, VAUXHALL Vivaro Van (X82) 1.6 CDTI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

Alternative products

Track rod end

Replacement: track rod end – VAUXHALL VIVARO Box. List of the tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      All-purpose cleaning spray
                    
                      Ceramic grease
                    
                      Torque wrench
                    
                      19 mm combination spanner
                    
                      21 mm combination spanner
                    
                      22 mm combination spanner
                    
                      32 mm combination spanner
                    
                      16 mm socket
                    
                      17 mm socket
                    
                      19 mm wheel impact socket
                    
                      Ratchet wrench or power tool for removal/installation of threaded fasteners
                    
                      Tommy bar
                    
                      Vernier caliper
                    
                      Ball joint separator
                    
                      Inner tie rod tool
                    
                      Slotted screwdriver
                    
                      Long nose pliers
                    
                      Combination pliers
                    
                      Tin snips
                    
                      Car lift or jack with jack stands, and wheel chocks

Buy tools

Replacement: track rod end – VAUXHALL VIVARO Box. AUTODOC experts recommend:

Replace the tie rod ends in pairs.
The replacement procedure is identical for the left and right tie rod ends.
All the work should be carried out with the ignition switched off.

Replacement: track rod end – VAUXHALL VIVARO Box. Recommended sequence of steps:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel fasteners. Use a 19 mm wheel impact socket. Use a tommy bar.
Step 3

Raise the vehicle.

Warning!
If you are using a jack, make sure the car is parked on a hard, flat surface.Make sure to additionally secure the car with jack stands.
Step 4

Unscrew the wheel fasteners.

Replacement: track rod end – VAUXHALL VIVARO Box. AUTODOC recommends:
To avoid injury, hold up the wheel when unscrewing the fasteners.
Step 5

Remove the wheel.
Step 6

Clean all tie rod end connections. Use a wire brush. Use WD-40 spray.
Step 7

Measure and note down the length of the exposed portion of the tie rod thread or the number of turns the tie rod end made when being unscrewed to prevent wheel misalignment during reassembly. Use a vernier caliper.
Step 8

Loosen the lock nut securing the tie rod end to the tie rod. Use a 19 mm combination spanner. Use a 21 mm combination spanner.
Step 9

Unscrew the fastener connecting the tie rod end to the steering knuckle. Use a 16 mm socket. Use a ratchet wrench.
Step 10

Disconnect the tie rod end from the steering knuckle. Use a ball joint separator.
Step 11

Unscrew the tie rod end from the tie rod.
Step 12

Unscrew the tie rod end lock nut.
Step 13

Clean the mounting seats of the tie rod end. Use a wire brush. Use an all-purpose cleaning spray.
Step 14

Screw on a new tie rod end lock nut.
Step 15

Screw on a new tie rod end.

Replacement: track rod end – VAUXHALL VIVARO Box. Professionals recommend:
When installing the tie rod end, remember to maintain the same length of the exposed tie rod thread or turn the tie rod end the same number of times.
Step 16

Connect the tie rod end to the steering knuckle.
Step 17

Tighten the fastener connecting the tie rod end to the steering knuckle. Use a 17 mm socket. Use a torque wrench. Tightening torque: 37 N·m.
Step 18

Tighten the tie rod end lock nut. Use a 19 mm combination spanner. Use a 22 mm combination spanner. Use a torque wrench. Tightening torque: 50 N·m.
Step 19

Clean the wheel rim mounting seat. Use a wire brush. Use an all-purpose cleaning spray.
Step 20

Treat the brake disc surface that contacts the wheel rim. Use ceramic grease.
Step 21

Install the wheel.

Replacement: track rod end – VAUXHALL VIVARO Box. Tip:
To avoid injury, hold up the wheel when screwing in the fasteners.
Step 22

Screw in the wheel fasteners. Use a 19 mm wheel impact socket. Use a ratchet wrench.
Step 23

Lower the car and tighten the wheel fasteners in a criss-cross pattern. Use a 19 mm wheel impact socket. Use a torque wrench. Tightening torque: 142 N·m.
Step 24

Remove the jack, jack stands, and wheel chocks.

Replacement: track rod end – VAUXHALL VIVARO Box. AUTODOC recommends:
After replacing the tie rods and tie rod ends, it is necessary to have the wheels aligned.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the VAUXHALL Vivaro Van (X82) model

VAUXHALL VIVARO Box tyre size

How to change front anti roll bar links on VAUXHALL Vivaro Van (X82) – replacement guide

Free download PDF 1.73 MB
How to change inner tie rod on VAUXHALL Vivaro Van (X82) – replacement guide

Free download PDF 1.95 MB
How to change front strut mount on VAUXHALL Vivaro Van (X82) – replacement guide

Free download PDF 6.23 MB
How to change rear shock absorbers on VAUXHALL Vivaro Van (X82) – replacement guide

Free download PDF 1.68 MB
How to change front suspension strut on VAUXHALL Vivaro Van (X82) – replacement guide

Free download PDF 7.06 MB
How to change rear brake caliper on VAUXHALL Vivaro Van (X82) – replacement guide

Free download PDF 2.29 MB

How to change track rod end on VAUXHALL Vivaro Van (X83) – replacement guide

Free download PDF 1.45 MB
How to change track rod end on VAUXHALL Vivaro Combi (X82) – replacement guide

Free download PDF 1.44 MB
How to change track rod end on VAUXHALL Vivaro Platform / Chassis (X83) – replacement guide

Free download PDF 1.45 MB
How to change track rod end on VAUXHALL Vivaro Minibus (J7) – replacement guide

Free download PDF 1.45 MB
How to change track rod end on VAUXHALL Vivaro Platform / Chassis (X82) – replacement guide

Free download PDF 1.44 MB
How to change track rod end on a car – replacement tutorial

Universal

Free download PDF 1.31 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY rear axle restoration | Drivetrain restoration – Part 2

9K views

Published on: 07/11/2024
How to Order Car Parts Online: Avoid These 5 Common Pitfalls

5K views

Published on: 10/03/2022
Myths about engine oils that need to be debunked

6K views

Published on: 22/01/2026
#DIY guide: Changing your car's color with a spray can | AUTODOC tips

6K views

Published on: 25/03/2021