Replacement: track rod end – FORD FIESTA Saloon JAS JBS. AUTODOC recommends:
Replace tie rod ends in pairs.
The replacement procedure is identical for the right and left tie rod ends.
Please note: all work on the car – FORD FIESTA Saloon JAS JBS – should be done with the engine switched off.
Carry out replacement in the following order:
Step 1
Secure the wheels with chocks.
Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 3
Raise the front of the car and secure on supports.
Step 4
Unscrew the wheel bolts.
AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. FORD FIESTA Saloon JAS JBS
Step 5
Remove the wheel.
Step 6
Clean the fastener connecting the tie rod end to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 7
Unscrew the end fastening nut to the steering knuckle. Use a drive socket #15. Use a tap wrench.
Step 8
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
Step 9
Loosen the lock nut securing the tie rod end to the tie rod. Use a combination spanner #22.
Step 10
Disconnect the tie rod end from the steering knuckle. Use a ball joint puller.
Step 11
Screw the end out of the tie rod.
Step 12
Clean the mounting seats of the tie rod end. Use a wire brush. Use WD-40 spray.
Step 13
Screw on a new tie rod end.
Replacement: track rod end – FORD FIESTA Saloon JAS JBS. AUTODOC experts recommend:
While installing the steering rod end remember to make the same number of turns or to leave the same length of thread showing as per your measurements.
Step 14
When deinstalling, mark or measure the precise position of the ball joint on the track rod, or count the number of turns in order to prevent misalignment afterward. Use a vernier caliper.
Step 15
Connect the tie rod end to the steering knuckle.
Step 16
Tighten the fastening nut connecting the tie rod end to the steering knuckle. Use a drive socket #17. Use a torque wrench. Tighten it to 48 nm torque.
Step 17
Tighten the tie rod end locknut. Use a combination spanner #19. Use a combination spanner #22. Use a torque wrench. Tighten it to 63 nm torque.
Step 18
Treat the fastener connecting the tie rod end to the steering knuckle. Use copper grease.
Step 19
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 20
Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends:
Replacement: track rod end – FORD FIESTA Saloon JAS JBS. After applying the spray, wait a few minutes.
Step 21
Install the wheel.
Replacement: track rod end – FORD FIESTA Saloon JAS JBS. Tip:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 22
Screw in the wheel bolts. Use wheel impact socket #19.
Step 23
Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #19. Use a torque wrench. Tighten it to 95 nm torque.
Replacement: track rod end – FORD FIESTA Saloon JAS JBS. Tip from AUTODOC:
Check and adjust wheel alignment if necessary.
Step 24
Remove the jacks and chocks.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Popular maintenance tutorials for Ford Fiesta Mk5 Saloon
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- scan the QR code
- download from App Store
- download from Google Play
Tips & tricks for your FORD Fiesta Mk5 Saloon (JAS, JBS)
View more
How to repair a chipped or cracked windscreen | AUTODOC tips
What to do if the ABS light comes on | AUTODOC tips