Important!
This replacement procedure can be used for:
TOYOTA AYGO (WNB1_, KGB1_) 1.0 (KGB10_)

The steps may slightly vary depending on the car design.

How to change front springs / front coil springs on TOYOTA AYGO 1 (AB10) [TUTORIAL AUTODOC]

Replacement: coil springs – Toyota Aygo AB1. List of the tools you'll need:
Replacement: coil springs – Toyota Aygo AB1. List of the tools you'll need:
Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #17
Combination spanner #19
XZN socket bit # 6
HEX bit No.H7
Drive socket # 15
Drive socket # 16
Drive socket # 17
12-point socket # 30
Wheel impact socket #19
Ratchet wrench
Torque wrench
Pin punch
Tap wrench
Hammer
Flat chisel
Crow bar
Round-nose pliers
Hydraulic strut spring compressor
Hydraulic transmission jack
Ball joint puller
Fender cover
Wheel chock
All the parts you need to replace – Springs for AYGO (WNB1_, KGB1_) and other TOYOTA models
How to change Coil Spring on Toyota Aygo ab1 1 – step-by-step instructions for straightforward car repair
Coil Spring
How to change Coil Spring on TOYOTA AYGO (WNB1_, KGB1_) 1.0 (KGB10_) – tips for proper car maintenance
TOYOTA AYGO (WNB1_, KGB1_) 1.0 (KGB10_)
Replacement: coil springs – Toyota Aygo AB1. Tip from AUTODOC:
  • Both coil springs of the front suspension should be replaced simultaneously.
  • The replacement procedure is identical for the left and right coil springs of the front suspension.
  • All work should be done with the engine stopped.
Replacement: coil springs – Toyota Aygo AB1. Recommended sequence of steps:
  1. How to change Springs on Toyota Aygo ab1 2005 - free PDF and video manuals
    Step 1
    Open the bonnet.
  2. How to replace TOYOTA AYGO (WNB1_, KGB1_) 1 2006 Springs - step-by-step manuals and video guides
    Step 2
    Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
  3. Toyota Aygo ab1 1.4 HDi 2007 Springs replacement: free workshop manuals
    Step 3
    Loosen the upper fastener of the shock strut mount.Use a combination spanner #17.Use HEX No.H7.
  4. Changing Springs on TOYOTA AYGO (WNB1_, KGB1_) 1 2008 by yourself
    Step 4
    Clean the wheel hub fastener.Use WD-40 spray.
  5. How to remove TOYOTA AYGO 1.4 HDi 2009 Springs - online easy-to-follow instructions
    Step 5
    Unstake the fastener of the driveshaft. Use a flat metal-working chisel.Use a hammer.
  6. How to replace Springs on TOYOTA AYGO (WNB1_, KGB1_) 2010: download PDF manuals and video instructions
    Step 6
    Loosen the fastener of the driveshaft. Use 12-point socket No.30. Use a tap wrench.
  7. How hard is it to do yourself: Springs replacement on Toyota Aygo ab1 1 2011 - download illustrated guide
    Step 7
    Secure the wheels with chocks.
  8. Need to know how to renew Springs on TOYOTA AYGO ? This free workshop manual will help you to do it yourself
    Step 8
    Loosen the wheel mounting bolts.Use wheel impact socket #19.
  9. Changing of Springs on Toyota Aygo ab1 2013 won't be an issue if you follow this illustrated step-by-step guide
    Step 9
    Raise the front of the car and secure on supports.
  10. TOYOTA AYGO 1.0 GPL (KGB10_) Springs replacement: online guides and video tutorials
    Step 10
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. Toyota Aygo AB1
  11. Replacing Springs on Toyota Aygo ab1 2005 1 by yourself
    Step 11
    Remove the wheel.
  12. AYGO (WNB1_, KGB1_) 1.4 HDi 2006 Springs DIY replacement workshop manual
    Step 12
    Disconnect the fastener of the ABS sensor cable from the shock absorber strut.
  13. How to change Springs on TOYOTA AYGO (WNB1_, KGB1_) 2007 - tips and tricks
    Step 13
    Clean the fasteners of the ABS sensor and of the brake hose which connect them to the shock strut. Clean the fasteners connecting the shock strut to the steering knuckle.Use a wire brush.Use WD-40 spray.
  14. Step-by-step recommendations for DIY replacement Toyota Aygo ab1 2008 1.4 HDi Springs
    Step 14
    Unscrew the brake hose fastening bracket from the shock strut.Use a drive socket #15.
  15. DIY replacement of Springs on TOYOTA AYGO (WNB1_, KGB1_) 1.0 GPL (KGB10_) 2009 is not an issue anymore with our step-by-step tutorial
    Step 15
    Unscrew the lower fastener connecting the shock strut to the steering knuckle.Use a combination spanner #17.Use a drive socket #17.Use a tap wrench.
  16. How to change Springs on Toyota Aygo ab1 2005 - free PDF and video manuals
    Step 16
    Remove the fastening bolt.
  17. How to replace TOYOTA AYGO (WNB1_, KGB1_) 1 2006 Springs - step-by-step manuals and video guides
    Step 17
    Clean all joints of the arm.Use a wire brush.Use WD-40 spray.
  18. Toyota Aygo ab1 1.4 HDi 2007 Springs replacement: free workshop manuals
    Step 18
    Remove the cotter pin.Use round-nose pliers.
  19. Changing Springs on TOYOTA AYGO (WNB1_, KGB1_) 1 2008 by yourself
    Step 19
    Unscrew the ball joint fastening to the steering knuckle.Use a combination spanner #19.
  20. How to remove TOYOTA AYGO 1.4 HDi 2009 Springs - online easy-to-follow instructions
    Step 20
    Prop up the steering knuckle.Use a hydraulic transmission jack.
  21. How to replace Springs on TOYOTA AYGO (WNB1_, KGB1_) 2010: download PDF manuals and video instructions
    Step 21
    Disconnect the lower arm from the steering knuckle.Use a ball joint puller.Use a crowbar.
  22. How hard is it to do yourself: Springs replacement on Toyota Aygo ab1 1 2011 - download illustrated guide
    Step 22
    Unscrew the fastener connecting the drive shaft to the wheel hub.Use 12-point socket No.30.
  23. Need to know how to renew Springs on TOYOTA AYGO ? This free workshop manual will help you to do it yourself
    Step 23
    Remove the drive shaft. Use a pin punch.Use a hammer.
  24. Changing of Springs on Toyota Aygo ab1 2013 won't be an issue if you follow this illustrated step-by-step guide
    Step 24
    Release the lower fastener connecting the shock strut to the steering knuckle. Use a flat metal-working chisel.Use a hammer.
  25. TOYOTA AYGO 1.0 GPL (KGB10_) Springs replacement: online guides and video tutorials
    Step 25
    Remove the support from under the steering knuckle.
    AUTODOC recommends:
    Replacement: coil springs – Toyota Aygo AB1. Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
  26. Replacing Springs on Toyota Aygo ab1 2005 1 by yourself
    Step 26
    Disconnect the steering knuckle from the shock absorber strut.Use a flat metal-working chisel.Use a hammer.
    Replacement: coil springs – Toyota Aygo AB1. Professionals recommend:
    Make sure that the steering knuckle is supported.
  27. AYGO (WNB1_, KGB1_) 1.4 HDi 2006 Springs DIY replacement workshop manual
    Step 27
    Unscrew the top fastening of the shock strut mount.
    AUTODOC recommends:
    Toyota Aygo AB1 – To avoid injury, hold the suspension strut while unscrewing the fastening bolts.
  28. How to change Springs on TOYOTA AYGO (WNB1_, KGB1_) 2007 - tips and tricks
    Step 28
    Remove the suspension strut.
  29. Step-by-step recommendations for DIY replacement Toyota Aygo ab1 2008 1.4 HDi Springs
    Step 29
    Set the shock absorber strut on the spring compressor tool.
    Replacement: coil springs – Toyota Aygo AB1. AUTODOC experts recommend:
    Note that when using a spring compressor, spring coils need to be securely gripped, compressing the spring on the opposite sides.Ensure the correct position of the spring in the retainer.Make sure that the spring coils tightly entered the lock handles.
  30. DIY replacement of Springs on TOYOTA AYGO (WNB1_, KGB1_) 1.0 GPL (KGB10_) 2009 is not an issue anymore with our step-by-step tutorial
    Step 30
    Compress the spring.
  31. How to change Springs on Toyota Aygo ab1 2005 - free PDF and video manuals
    Step 31
    Treat the shock strut rod.Use a wire brush.Use WD-40 spray.
  32. How to replace TOYOTA AYGO (WNB1_, KGB1_) 1 2006 Springs - step-by-step manuals and video guides
    Step 32
    Remove the strut piston rod nut.Use a combination spanner #17.Use XZN #6. Use a ratchet wrench.
  33. Toyota Aygo ab1 1.4 HDi 2007 Springs replacement: free workshop manuals
    Step 33
    Remove the top strut mount.
  34. Changing Springs on TOYOTA AYGO (WNB1_, KGB1_) 1 2008 by yourself
    Step 34
    Release the coil spring.
  35. How to remove TOYOTA AYGO 1.4 HDi 2009 Springs - online easy-to-follow instructions
    Step 35
    Remove the shock absorber dust cap and the bump stop.
    AUTODOC recommends:
    Replacement: coil springs – Toyota Aygo AB1. Carefully inspect the mount, the boot, and the bump stop of the shock absorber. Replace if necessary.
  36. How to replace Springs on TOYOTA AYGO (WNB1_, KGB1_) 2010: download PDF manuals and video instructions
    Step 36
    Remove the spring.
  37. How hard is it to do yourself: Springs replacement on Toyota Aygo ab1 1 2011 - download illustrated guide
    Step 37
    Install the spring on the shock absorber.
  38. Need to know how to renew Springs on TOYOTA AYGO ? This free workshop manual will help you to do it yourself
    Step 38
    Install the boot and a bump stop onto the shock absorber.
  39. Changing of Springs on Toyota Aygo ab1 2013 won't be an issue if you follow this illustrated step-by-step guide
    Step 39
    Compress the spring.
  40. TOYOTA AYGO 1.0 GPL (KGB10_) Springs replacement: online guides and video tutorials
    Step 40
    Install the upper strut mount and the strut mount bearing.
  41. Replacing Springs on Toyota Aygo ab1 2005 1 by yourself
    Step 41
    Tighten the shock strut piston rod nut. Use a combination spanner #17.Use XZN #6. Use a torque wrench.Tighten it to 60 Nm torque.
    Replacement: coil springs – Toyota Aygo AB1. Tip from AUTODOC:
    Check to make sure the spring is positioned correctly. Avoid its misalignment.
  42. AYGO (WNB1_, KGB1_) 1.4 HDi 2006 Springs DIY replacement workshop manual
    Step 42
    Decompress the spring.
  43. How to change Springs on TOYOTA AYGO (WNB1_, KGB1_) 2007 - tips and tricks
    Step 43
    Remove the assembled shock strut.
  44. Step-by-step recommendations for DIY replacement Toyota Aygo ab1 2008 1.4 HDi Springs
    Step 44
    Install the shock strut into the wheel arch.
  45. DIY replacement of Springs on TOYOTA AYGO (WNB1_, KGB1_) 1.0 GPL (KGB10_) 2009 is not an issue anymore with our step-by-step tutorial
    Step 45
    Screw the top fastening of the shock strut mount.Do not tighten it.
    AUTODOC recommends:
    Toyota Aygo AB1 – To avoid injury, hold the suspension strut while screwing in the fastening bolts.
  46. How to change Springs on Toyota Aygo ab1 2005 - free PDF and video manuals
    Step 46
    Clean the mounting seats of the shock strut.Use a wire brush.Use WD-40 spray.
  47. How to replace TOYOTA AYGO (WNB1_, KGB1_) 1 2006 Springs - step-by-step manuals and video guides
    Step 47
    Fix the shock absorber strut on the steering knuckle.
  48. Toyota Aygo ab1 1.4 HDi 2007 Springs replacement: free workshop manuals
    Step 48
    Clean the splines of the drive shaft CV joint. Use a wire brush.Use WD-40 spray.
  49. Changing Springs on TOYOTA AYGO (WNB1_, KGB1_) 1 2008 by yourself
    Step 49
    Treat the splines of the driveshaft CV joint. Use copper grease.
  50. How to remove TOYOTA AYGO 1.4 HDi 2009 Springs - online easy-to-follow instructions
    Step 50
    Mount the drive shaft into the wheel hub.
  51. How to replace Springs on TOYOTA AYGO (WNB1_, KGB1_) 2010: download PDF manuals and video instructions
    Step 51
    Connect the lower arm to the steering knuckle.Use a crowbar.
  52. How hard is it to do yourself: Springs replacement on Toyota Aygo ab1 1 2011 - download illustrated guide
    Step 52
    Screw the fasteners of the ball joint.Use a combination spanner #19.
  53. Need to know how to renew Springs on TOYOTA AYGO ? This free workshop manual will help you to do it yourself
    Step 53
    Install the fastening bolt.
  54. Changing of Springs on Toyota Aygo ab1 2013 won't be an issue if you follow this illustrated step-by-step guide
    Step 54
    Screw in the fastener that connects the shock strut to the steering knuckle.Use a drive socket #17.Use a combination spanner #17.
  55. TOYOTA AYGO 1.0 GPL (KGB10_) Springs replacement: online guides and video tutorials
    Step 55
    Tighten the brake hose fastening bracket to the shock strut.Use a drive socket #15.
  56. Replacing Springs on Toyota Aygo ab1 2005 1 by yourself
    Step 56
    Connect the fastener of the ABS sensor cable to the shock absorber strut.
  57. AYGO (WNB1_, KGB1_) 1.4 HDi 2006 Springs DIY replacement workshop manual
    Step 57
    Tighten the lower fasteners connecting the shock strut to the steering knuckle.Use a drive socket #17.Use a torque wrench.Tighten it to 105 Nm torque.
  58. How to change Springs on TOYOTA AYGO (WNB1_, KGB1_) 2007 - tips and tricks
    Step 58
    Tighten the ball joint fastener. Use a drive socket #16.Use a torque wrench.Tighten it to 50 nm torque.
  59. Step-by-step recommendations for DIY replacement Toyota Aygo ab1 2008 1.4 HDi Springs
    Step 59
    Install the cotter pin.
    Step 60
    Treat the shock strut fasteners.Use copper grease.
  60. DIY replacement of Springs on TOYOTA AYGO (WNB1_, KGB1_) 1.0 GPL (KGB10_) 2009 is not an issue anymore with our step-by-step tutorial
    Step 61
    Screw the nut of the drive shaft.Use 12-point socket No.30.
  61. How to change Springs on Toyota Aygo ab1 2005 - free PDF and video manuals
    Step 62
    Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
  62. How to replace TOYOTA AYGO (WNB1_, KGB1_) 1 2006 Springs - step-by-step manuals and video guides
    Step 63
    Clean the brake disk surface.Use a brake cleaner.
    AUTODOC recommends:
    Replacement: coil springs – Toyota Aygo AB1. After applying the spray, wait a few minutes.
  63. Toyota Aygo ab1 1.4 HDi 2007 Springs replacement: free workshop manuals
    Step 64
    Install the wheel.
    AUTODOC recommends:
    Important! Hold the wheel while screwing in the fastening bolts. Toyota Aygo AB1
  64. Changing Springs on TOYOTA AYGO (WNB1_, KGB1_) 1 2008 by yourself
    Step 65
    Screw in the wheel bolts.Use wheel impact socket #19.
  65. How to remove TOYOTA AYGO 1.4 HDi 2009 Springs - online easy-to-follow instructions
    Step 66
    Lower the car.
  66. How to replace Springs on TOYOTA AYGO (WNB1_, KGB1_) 2010: download PDF manuals and video instructions
    Step 67
    Tighten the drive shaft nut.Use 12-point socket No.30. Use a torque wrench.Tighten it to 115 nm torque.
  67. How hard is it to do yourself: Springs replacement on Toyota Aygo ab1 1 2011 - download illustrated guide
    Step 68
    Restake the fastener of the driveshaft.Use a flat metal-working chisel.Use a hammer.
  68. Need to know how to renew Springs on TOYOTA AYGO ? This free workshop manual will help you to do it yourself
    Step 69
    Tighten the upper fastener of the shock absorber strut mount.Use a combination spanner #17.Use HEX No.H7.Use a drive socket #17.Use a torque wrench.Tighten it to 50 Nm torque.
  69. Changing of Springs on Toyota Aygo ab1 2013 won't be an issue if you follow this illustrated step-by-step guide
    Step 70
    Tighten the wheel bolts using a criss-cross pattern.Use a torque wrench.Tighten it to 120 Nm torque.
  70. TOYOTA AYGO 1.0 GPL (KGB10_) Springs replacement: online guides and video tutorials
    Step 71
    Remove the jacks and chocks.
    Step 72
    Remove the fender protection cover.
  71. Replacing Springs on Toyota Aygo ab1 2005 1 by yourself
    Step 73
    Close the hood.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Google Play AUTODOC Club App
App Store AUTODOC Club App
TOYOTA AYGO (WNB1_, KGB1_) Springs replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY TOYOTA AYGO (WNB1_, KGB1_) Springs replacement - online guide
Tips & tricks for your TOYOTA AYGO (WNB1_, KGB1_)
View more
  • How to change Suspension springs on TOYOTA AYGO (WNB1_, KGB1_) 1.0 GPL (KGB10_) - replacement tricks
    How to clean a really dirty car interior | AUTODOC
  • Changing Coil springs Toyota Aygo ab1 1 - Replacement Tips
    How to install snow chains | AUTODOC
  • Maintenance Hacks - TOYOTA AYGO (WNB1_, KGB1_) 1.4 HDi Coil spring replacement guide
    How to diagnose engine malfunctions with an OBD2 scanner | AUTODOC
  • Replace Suspension spring on Toyota Aygo ab1 - free video tips
    How to get rid of a bad smell in your car | AUTODOC

Manuals for TOYOTA models