Disclaimer
How to change spark plugs on FORD MAVERICK – replacement guide
downloads:
0
Views:
54
Recommended replacement interval for the part category Spark plug : 5 year / 90000 km
Important!
This replacement procedure can be used for:
FORD MAVERICK 2.0 16V … View more
The steps may slightly vary depending on the car design.
FORD MAVERICK 2.0 16V … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Spark Plug for MAVERICK and other FORD models
High-temperature anti-seize lubricant
Drive socket # 10
Spark plug socket # 16
Ratchet wrench
Torque wrench
Round-nose pliers
Clic-R collar pliers
Microfibre towel
Fender cover
Replacement: spark plugs – FORD MAVERICK. Tip from AUTODOC:
- The replacement procedure is the same for all spark plugs.
- All work should be done with the engine stopped.
Replacement: spark plugs – FORD MAVERICK. Take the following steps:
- Step 1Open the bonnet.Step 2Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.Step 3
Disconnect the air intake pipe from the air filter housing. - Step 4
Detach the air intake hose clamp. Use clic-R collar pliers. - Step 5
Remove the air intake pipe. - Step 6
Unscrew the filter housing fastening bolts. Use a drive socket #10. Use a ratchet wrench. - Step 7Detach the crankcase ventilation hose from the engine cover at the left.Step 8
Remove the air filter housing.Please note!The air filter housing is integrated into the engine cover. - Step 9
Cover the air intake hose with a microfibre towel to prevent dust and dirt from getting into the system. - Step 10
Remove the spark plug wire connectors from the spark plug wells. Use round-nose pliers.Replacement: spark plugs – FORD MAVERICK. Professionals recommend:Be careful to avoid damaging spark plug wires.Remember the sequence of the spark plug wires connectors. - Step 11
Clean dirt, dust and debris from inside the spark plug wells. - Step 12
Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench. - Step 13
Take out the spark plugs. - Step 14
Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new spark plugs. - Step 15
Install the new spark plugs into their mounting seats. - Step 16
Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque wrench. Tighten it to 15 nm torque.Replacement: spark plugs – FORD MAVERICK. AUTODOC recommends:Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Popular maintenance tutorials for Ford Maverick 1n2
Free download PDF
665.6 KB
Free download PDF1.41 MB
Free download PDF1.48 MB
Free download PDF7.83 MB
Free download PDF2.14 MB
Free download PDF2.92 MB
Complete guides for changing the Engine spark plug on different FORD MAVERICK models
Free download PDF1.74 MB
Free download PDF1.77 MB
Free download PDF952.32 KB
Free download PDF1.22 MB
Free download PDF1.09 MB
Free download PDF788.48 KB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your FORD MAVERICK
View more
8 bad driving habits | AUTODOC tips
DIY jack restoration | AUTODOC tips
How to save when buying car parts
How to restore a steering wheel | AUTODOC tips
