Disclaimer
How to change rear wheel bearing on FIAT Strada Pickup (178) – replacement guide
downloads:
30
Views:
259
Important!
This replacement procedure can be used for:
FIAT Strada Pickup (178_) 1.2, FIAT Strada Pickup (178_) 1.9 JTD, FIAT Strada Pickup (178_) 1.9 D, FIAT Strada Pickup (178_) 1.7 TD, FIAT Strada Pickup (178_) 1.2 … View more
The steps may slightly vary depending on the car design.
FIAT Strada Pickup (178_) 1.2, FIAT Strada Pickup (178_) 1.9 JTD, FIAT Strada Pickup (178_) 1.9 D, FIAT Strada Pickup (178_) 1.7 TD, FIAT Strada Pickup (178_) 1.2 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Wheel Bearing for Strada Pickup (178_) and other FIAT models
Alternative products

Wire brush
WD-40 spray
All-purpose cleaning spray
Copper grease
Drive socket # 12
Drive socket # 32
Wheel impact socket #19
Ratchet wrench
Torque wrench
Hammer
Tap wrench
Rubber mallet
Crow bar
Wheel chock
Replacement: wheel bearing – FIAT STRADA Pickup (178E). Tip from AUTODOC:
- Do not re-use the bearing assembly of your FIAT STRADA Pickup (178E) car.
- The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
- Please note: all work on the car – FIAT STRADA Pickup (178E) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #19. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Important! Hold the wheel while unscrewing the fastening bolts. FIAT STRADA Pickup (178E) - Step 5
Remove the wheel. - Step 6
Clean the brake drum. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the brake drum fastening. Use a drive socket #12. Use a ratchet wrench. - Step 8
Remove the brake drum.Replacement: wheel bearing – FIAT STRADA Pickup (178E). Tip from AUTODOC experts:Examine the brake drum. Replace it if necessary. - Step 9
Remove the hub bearing protection cap. Use a crowbar. Use a hammer.Replacement: wheel bearing – FIAT STRADA Pickup (178E). AUTODOC experts recommend:Some cars are not equipped with wheel hub caps. - Step 10
Unscrew the wheel hub axle nut. Use a drive socket #32. Use a tap wrench. - Step 11
Remove the hub and the bearing together, since they are a sealed unit. - Step 12
Clean the hub bearing mounting seat. Use all-purpose cleaning spray. - Step 13
Install the new wheel hub with a bearing. - Step 14
Tighten the hub. Use a drive socket #32. Use a torque wrench. Tighten it to 280 nm torque.Replacement: wheel bearing – FIAT STRADA Pickup (178E). Tip:The wheel bearing unit must not tilt on the axle pin.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the FIAT Strada Pickup (178) model
Popular maintenance tutorials for Fiat Strada 178E
Complete guides for changing the Wheel bearings on different FIAT STRADA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your FIAT Strada Pickup (178_)
View more
How to get your motorcycle ready for spring
DIY manual gearbox restoration | Drivetrain restoration – Part 3
Extend your engine's life: Avoid these 3 damaging factors | AUTODOC tips
#DIY Wheel Rim Restoration: Revive Scratches and Chips Easily!
Most commonly replaced car parts on FIAT STRADA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME


























