Important!

This replacement procedure can be used for:
FIAT BRAVA (182) 1.6 16V (182.BH), FIAT BRAVA (182) 1.8 GT 16V (182.BC), FIAT BRAVA (182) 1.6 16V (182.BB), FIAT BRAVA (182) 1.9 TD 100 S (182.BF), FIAT BRAVA (182) 1.9 TD 75 S (182.BF), FIAT BRAVA (182) 1.9 D, FIAT BRAVA (182) 1.9 JTD 105, FIAT BRAVA (182) 1.2 16V 80, FIAT BRAVA (182) 1.2 16V 80, FIAT BRAVA (182) 1.9 JTD, FIAT BRAVA (182) 1.6 16V (182.BU), FIAT BRAVA (182) 1.4 (182.BG), FIAT BRAVA (182) 1.6 16V, FIAT BRAVA (182) 1.8 16V … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Wheel Bearing for BRAVA (182) and other FIAT models

Wheel bearing kit

Wheel bearing

        Wheel bearing kit for FIAT BRAVA (182) 1.4 (182.BG) Petrol (75 hp)
      
        Wheel bearing kit for FIAT BRAVA (182) 1.6 16V (182.BH) Petrol (90 hp)
      
        Wheel bearing kit for FIAT BRAVA (182) 1.8 GT 16V (182.BC) Petrol (113 hp)
      
        Wheel bearing kit for FIAT BRAVA (182) 1.6 16V (182.BB) Petrol (103 hp)
      
        Wheel bearing kit for FIAT BRAVA (182) 1.9 TD 100 S (182.BF) Diesel (100 hp)
      
        Wheel bearing kit for FIAT BRAVA (182) 1.9 TD 75 S (182.BF) Diesel (75 hp)
      
        Wheel bearing kit for FIAT BRAVA (182) 1.9 D Diesel (65 hp)
      
        Wheel bearing kit for FIAT BRAVA (182) 1.9 JTD 105 Diesel (105 hp)
      
        Wheel bearing kit for FIAT BRAVA (182) 1.2 16V 80 Petrol (82 hp)

Replacement: wheel bearing – FIAT BRAVA (182). List of the tools you'll need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        All-purpose cleaning spray
                      
                        Copper grease 
                      
                        Drive socket # 12 
                      
                        Drive socket # 13 
                      
                        Drive socket # 17 
                      
                        Drive socket # 32 
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Tap wrench
                      
                        Hammer
                      
                        Rubber mallet
                      
                        Crow bar
                      
                        Wheel chock

Buy tools

Replacement: wheel bearing – FIAT BRAVA (182). AUTODOC experts recommend:

Do not re-use the bearing assembly of your FIAT BRAVA (182) car.
The wheel hub bearing replacement procedure is identical for both wheels on the same axle.
All work should be done with the engine stopped.

Replacement: wheel bearing – FIAT BRAVA (182). Use the following procedure:

Step 1

Secure the wheels with chocks.
Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. FIAT BRAVA (182)
Step 5

Remove the wheel.
Step 6

Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the brake caliper fastening. Use a drive socket #13. Use a ratchet wrench.
Step 8

Remove the brake caliper. Use a crowbar.

Replacement: wheel bearing – FIAT BRAVA (182). AUTODOC recommends:
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
Step 9

Remove the brake pads.
Step 10

Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 11

Unscrew the caliper bracket fastening. Use a drive socket #17. Use a tap wrench.
Step 12

Remove the caliper bracket.
Step 13

Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
Step 14

Unscrew the brake disc fastening. Use a drive socket #12. Use a ratchet wrench.
Step 15

Remove the brake disc. Use a rubber mallet.
Step 16

Remove the hub bearing protection cap. Use a crowbar. Use a hammer.

Replacement: wheel bearing – FIAT BRAVA (182). Tip from AUTODOC experts:
Some cars are not equipped with wheel hub caps.
Step 17

Unscrew the wheel hub axle nut. Use a drive socket #32. Use a tap wrench.
Step 18

Remove the hub and the bearing together, since they are a sealed unit.
Step 19

Clean the hub bearing mounting seat. Use all-purpose cleaning spray.
Step 20

Install the new wheel hub with a bearing.
Step 21

Tighten the hub. Use a drive socket #32. Use a torque wrench. Tighten it to 224 Nm torque.

Replacement: wheel bearing – FIAT BRAVA (182). Tip:
The wheel bearing unit must not tilt on the axle pin.
Step 22

Install the hub bearing protection cap. Use a rubber mallet.
Step 23

Treat the hub where it contacts the brake disk. Use copper grease.
Step 24

Install the brake disc.
Step 25

Tighten the brake disc fastening. Use a drive socket #12. Use a torque wrench. Tighten it to 10 Nm torque.
Step 26

Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.

AUTODOC recommends:
Replacement: wheel bearing – FIAT BRAVA (182). After applying the spray, wait a few minutes.
Step 27

Install the brake caliper bracket.
Step 28

Tighten the brake caliper bracket. Use a drive socket #17. Use a torque wrench. Tighten it to 62 Nm torque.
Step 29

Install the brake pads.
Step 30

Install the brake caliper and fix it. Use a drive socket #13. Use a torque wrench. Tighten it to 30 Nm torque.
Step 31

Clean the brake disk surface. Use a wire brush.

Step 32

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 33

Clean the brake disk surface. Use a brake cleaner.

Replacement: wheel bearing – FIAT BRAVA (182). Tip from AUTODOC experts:
After applying the spray, wait a few minutes.
Step 34

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. FIAT BRAVA (182)
Step 35

Screw in the wheel bolts. Use wheel impact socket #17.
Step 36

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 120 Nm torque.
Step 37

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

How to change front wheel bearing on FIAT BRAVA (182) – replacement guide

Free download PDF
2.03 MB
How to change spark plugs on FIAT BRAVA (182) – replacement guide

Free download PDF
1.46 MB
How to change engine oil and filter on FIAT BRAVA (182) – replacement guide

Free download PDF
1.88 MB
How to change brake drum on FIAT BRAVA (182) – replacement guide

Free download PDF
1.19 MB
How to change fuel filter on Fiat Doblo Cargo – replacement guide

Free download PDF
2.14 MB
How to change serpentine belt on Fiat Doblo Cargo – replacement guide

Free download PDF
2.43 MB

How to change rear wheel bearing on Fiat Bravo 2 – replacement guide

Free download PDF
2.49 MB
How to change front wheel bearing on FIAT BRAVA (182) – replacement guide

Free download PDF
2.03 MB
How to change rear wheel bearing on FIAT BRAVO I (182) – replacement guide

Free download PDF
2.44 MB
How to change front wheel bearing on FIAT BRAVO I (182) – replacement guide

Free download PDF
2.03 MB
How to change wheel bearing on a car – replacement tutorial

Universal

Free download PDF
2.41 MB
How to change front wheel bearing on Fiat Punto 188 – replacement guide

Free download PDF
2.05 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

5 tools that make car repair incredibly simple | AUTODOC tips

36K views

Published on: 25/01/2024
3 things to know before buying summer tyres | AUTODOC tips

3K views

Published on: 18/05/2023
How to Make a DIY Foam Sprayer | AUTODOC tips

199K views

Published on: 23/06/2022
How to remove scratches from a car | AUTODOC tips

7K views

Published on: 12/05/2022