Disclaimer
How to change rear strut mount on AUDI A4 Convertible (8H7, B6, 8HE, B7) – replacement guide
downloads:
2
Views:
27
Important!
This replacement procedure can be used for:
AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.4, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.4, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.5 TDI, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0 quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) S4 quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.0, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0 … View more
The steps may slightly vary depending on the car design.
AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.4, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.4, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.5 TDI, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0 quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) S4 quattro, AUDI A4 Convertible (8H7, B6, 8HE, B7) 2.0, AUDI A4 Convertible (8H7, B6, 8HE, B7) 1.8 T, AUDI A4 Convertible (8H7, B6, 8HE, B7) 3.0 … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Strut Mount for A4 Convertible (8H7, B6, 8HE, B7) and other AUDI models
Alternative products

Wire brush
WD-40 spray
Brake cleaner
Copper grease
Combination spanner #17
Combination spanner #21
Drive socket # 13
Drive socket # 21
Torx bit T25
Wheel impact socket #17
Ratchet wrench
Torque wrench
Adjustable wrench
Hammer
Pin punch
Rubber mallet
Hydraulic transmission jack
Wheel chock
Replacement: strut mount – AUDI A4 Convertible (8H7, B6, 8HE, B7). Tip from AUTODOC experts:
- The replacement procedure is identical for the mounts of the right and left shock absorbers of the rear suspension.
- Both mounts of the rear shock struts should be replaced simultaneously.
- Please note: all work on the car – AUDI A4 Convertible (8H7, B6, 8HE, B7) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Secure the wheels with chocks. - Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the rear of the car and secure on supports.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. AUDI A4 Convertible (8H7, B6, 8HE, B7) - Step 5
Remove the wheel. - Step 6.1
Unscrew and remove the wheel arch cover fasteners. Use a drive socket #13.Step 6.2
Use Torx T25. Use a ratchet wrench. - Step 7
Remove the wheel arch cover. - Step 8
Clean the shock absorber fasteners. Use a wire brush. Use WD-40 spray. - Step 9
Unscrew the lower fastener of the shock absorber. Use a combination spanner #21. Use a drive socket #21. Use a ratchet wrench. - Step 10
Support the arm. Use a hydraulic transmission jack. - Step 11
Remove the fastening bolt. - Step 12Detach the lower part of the shock absorber. Use a pin punch. Use a hammer.Step 13Remove the support from under the arm.AUTODOC recommends:Replacement: strut mount – AUDI A4 Convertible (8H7, B6, 8HE, B7). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.Step 14
Unscrew the upper fastener of the shock absorber. Use a drive socket #13. Use a ratchet wrench.Replacement: strut mount – AUDI A4 Convertible (8H7, B6, 8HE, B7). Tip:To avoid injuries, hold the shock absorber when undoing the fastening bolts. - Step 15
Remove the shock absorber. - Step 16
Clean the shock absorber rod fastener. Use a wire brush. Use WD-40 spray. - Step 17
Remove the shock absorber piston rod fastening. Use a combination spanner #17. Use an adjustable wrench. - Step 18
Remove the top mount. - Step 19Remove the shock absorber dust cap and the bump stop.Step 20
Install the new mount, boot, and bump stop on the shock absorber. - Step 21
Tighten the shock absorber rod nut. Use a combination spanner #17. Use an adjustable wrench. Use a torque wrench. Tighten it to 25 Nm torque. - Step 22
Clean the shock absorber mounting seats. Use a wire brush. Use WD-40 spray. - Step 23
Place the shock absorber in the wheel arch and secure it.AUTODOC recommends:Important! Hold the shock absorber while screwing in the fastening bolts. AUDI A4 Convertible (8H7, B6, 8HE, B7)
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the AUDI A4 B6/B7 Convertible (8H7, 8HE) model
Popular maintenance tutorials for Audi A4 Convertible
Complete guides for changing the Strut mount on different AUDI A4 models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your AUDI A4 Convertible (8H7, B6, 8HE, B7)
View more
How to Polish Your Car Yourself and Save Money on Garage Services | AUTODOC tips
2 ways to clean the EGR valve – which one is better?
Motorcycle fuel tank restoration
5 most common causes of oil leaks | AUTODOC tips
Most commonly replaced car parts on AUDI A4
Time to replace parts? Get even better deals in our Shop app.

SCAN ME
































