How to change rear brake discs on VOLVO S40 II (544) – replacement guide
downloads:
2
Views:
39
0
Users voted – 0
Recommended replacement interval for the part category Brake disc : 50000km
Important!
This replacement procedure can be used for:
VOLVO S40 II (544) D3,
VOLVO S40 II (544) D4,
VOLVO S40 II (544) D2,
VOLVO S40 II (544) 2.0 F,
VOLVO S40 II (544) 2.4,
VOLVO S40 II (544) 2.4,
VOLVO S40 II (544) T5,
VOLVO S40 II (544) 2.0 D,
VOLVO S40 II (544) T5 AWD,
VOLVO S40 II (544) 1.8,
VOLVO S40 II (544) 1.6,
VOLVO S40 II (544) 1.6 D,
VOLVO S40 II (544) 2.0,
VOLVO S40 II (544) D5,
VOLVO S40 II (544) T5,
VOLVO S40 II (544) T5 AWD,
VOLVO S40 II (544) 1.8 FlexFuel,
VOLVO S40 II (544) D4,
VOLVO S40 II (544) 2.0 CDI,
VOLVO S40 II (544) 2.4 CDI,
VOLVO S40 II (544) 2.4 AWD
…
View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Discs for S40 II (544) and other VOLVO models
Replacement: brake discs – VOLVO S40 II (MS). AUTODOC recommends:
Replace the brake disks on the car VOLVO S40 II (MS) in complete set for each axis. Regardless of the state of components. This will ensure even braking.
The replacement procedure is identical for both brake disks on the same axle.
When changing the brake discs, always replace the brake pads.
Warning! Shut down the engine before starting any work – VOLVO S40 II (MS).
Carry out replacement in the following order:
Step 1
Open the bonnet. Unscrew the brake fluid reservoir cap.
Step 2
Secure the wheels with chocks.
Step 3
Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 4
Raise the rear of the car and secure on supports.
Step 5
Unscrew the wheel bolts.
Replacement: brake discs – VOLVO S40 II (MS). Tip:
To avoid injury, hold up the wheel when unscrewing the bolts.
Step 6
Remove the wheel.
Step 7
Remove the dust boot caps of the brake caliper guide pins. Use a crowbar.
Step 8
Unscrew the brake caliper fastening. Use HEX No.H7. Use a ratchet wrench.
Step 9
Detach the brake caliper retaining spring. Use a crowbar.
Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
Step 11
Remove the brake pads. Use a crowbar.
Step 12
Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
Step 13
Unscrew the caliper bracket fastening. Use a drive socket #13. Use a ratchet wrench. Use a tap wrench.
Step 14
Remove the caliper bracket.
Step 15
Remove the brake disc. Use a rubber mallet.
Step 16
Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
Replacement: brake discs – VOLVO S40 II (MS). Tip from AUTODOC:
After applying the spray, wait a few minutes.
Step 17
Clean the hub. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 18
Install the brake disc.
Step 19
Install the brake caliper bracket.
Step 20
Tighten the brake caliper bracket. Use a drive socket #13. Use a torque wrench. Tighten it to 70 Nm torque.
Step 21
Treat the brake caliper piston. Use a brake cleaner.
AUTODOC recommends:
Replacement: brake discs – VOLVO S40 II (MS). After applying the spray, wait a few minutes.
Step 22
Press in the brake caliper piston. Use brake caliper wind back tool.
Step 23
Treat the brake pads in the area where their surface comes into contact with the brake caliper bracket. Use anti-squeal paste.
Step 24
Install the brake pads.
Step 25
Install the brake caliper and fix it. Use HEX No.H7. Use a torque wrench. Tighten it to 35 Nm torque.
Step 26
Install the dust boot caps of the brake caliper guide pins.
Step 27
Install the brake caliper retaining spring. Use a rubber mallet.
Step 28
Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 29
Clean the brake disk surface. Use a brake cleaner.
Replacement: brake discs – VOLVO S40 II (MS). Professionals recommend:
After applying the spray, wait a few minutes.
Step 30
Install the wheel.
AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. VOLVO S40 II (MS)
Step 31
Screw in the wheel bolts. Use wheel impact socket #19.
Step 32
Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 110 Nm torque.
Step 33
Remove the jacks and chocks.
Replacement: brake discs – VOLVO S40 II (MS). AUTODOC recommends:
Check the brake fluid level in the expansion tank and refill if necessary.
Step 34
Tighten the brake fluid reservoir cap.
AUTODOC recommends:
VOLVO S40 II (MS) – Without starting the engine, press the brake pedal several times until it feels firm.
Step 35
Close the hood.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.