Important!

This replacement procedure can be used for:
VW Jetta Mk5 (1K) 1.6 TDI, VW Jetta Mk5 (1K) 1.6, VW Jetta Mk5 (1K) 1.6 FSI, VW Jetta Mk5 (1K) 2.0 FSI, VW Jetta Mk5 (1K) 1.9 TDI, VW Jetta Mk5 (1K) 2.0 TDI 16V, VW Jetta Mk5 (1K) 2.0 TFSI, VW Jetta Mk5 (1K) 2.0 TDI, VW Jetta Mk5 (1K) 1.4 TSI, VW Jetta Mk5 (1K) 1.4 TSI, VW Jetta Mk5 (1K) 2.0 TDI, VW Jetta Mk5 (1K) 2.0 TDI, VW Jetta Mk5 (1K) 1.4 TSI, VW Jetta Mk5 (1K) 2.5, VW Jetta Mk5 (1K) 2.5, VW Jetta Mk5 (1K) 1.4 TSI, VW Jetta Mk5 (1K) 1.6 TDI, VW Jetta Mk5 (1K) 1.6 MultiFuel … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Anti Roll Bar Links for Jetta Mk5 (1K) and other VW models

Anti-roll bar link

        Anti-roll bar link for Jetta Mk5 (1K) Diesel (90 hp)
      
        Anti-roll bar link for Jetta Mk5 (1K) Petrol (102 hp)
      
        Anti-roll bar link for Jetta Mk5 (1K) Petrol (115 hp)
      
        Anti-roll bar link for Jetta Mk5 (1K) Petrol (150 hp)
      
        Anti-roll bar link for Jetta Mk5 (1K) Diesel (105 hp)
      
        Anti-roll bar link for Jetta Mk5 (1K) Diesel (140 hp)
      
        Anti-roll bar link for Jetta Mk5 (1K) Petrol (200 hp)
      
        Anti-roll bar link for Jetta Mk5 (1K) Diesel (136 hp)
      
        Anti-roll bar link for Jetta Mk5 (1K) Petrol (140 hp)

Replacement: anti roll bar links – VW JETTA III (1K2). Tools you might need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Brake cleaner 
                      
                        Copper grease 
                      
                        Torque wrench
                      
                        Combination spanner #16
                      
                        Drive socket # 16 
                      
                        XZN socket bit # 6
                      
                        Wheel impact socket #17
                      
                        Ratchet wrench
                      
                        Hydraulic transmission jack
                      
                        Wheel chock

Buy tools

AUTODOC recommends:

Replace the stabiliser links on VW JETTA III (1K2) in pairs.
The replacement procedure is identical for both stabiliser links on the same axle.
Please note: all work on the car – VW JETTA III (1K2) – should be done with the engine switched off.

Carry out replacement in the following order:

Step 1

Secure the wheels with chocks.

Step 2

Loosen the wheel mounting bolts. Use wheel impact socket #17.
Step 3

Raise the rear of the car and secure on supports.

Step 4

Unscrew the wheel bolts.

AUTODOC recommends:
Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW JETTA III (1K2)
Step 5

Remove the wheel.
Step 6

Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 7

Unscrew the fastener connecting the stabilizer bar with the control arm. Use a drive socket #16. Use a ratchet wrench.
Step 8

Clean all joints of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 9

Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench.
Step 10

Support the arm. Use a hydraulic transmission jack.
Step 11

Remove the stabilizer rod.
Step 12

Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray.
Step 13

Ιnstall the transverse stabilizer link.
Step 14

Tighten the stabiliser link fastener. Use a combination spanner #16. Use XZN #6. Use a ratchet wrench.
Step 15

Raise the hydraulic transmission jack by 10-15 cm.
Step 16

Tighten the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #16. Use XZN #6. Use a drive socket #16. Use a torque wrench. Tighten it to 45 Nm torque.
Step 17

Tighten the fastener connecting the stabilizer bar with the control arm. Use a combination spanner #16. Use XZN #6. Use a drive socket #16. Use a torque wrench. Tighten it to 45 Nm torque.
Step 18

Treat all joints of the stabiliser link. Use copper grease.
Step 19

Remove the support from under the arm.

AUTODOC recommends:
Replacement: anti roll bar links – VW JETTA III (1K2). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 20

Clean the wheel rim mounting seat. Use a wire brush.
Step 21

Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
Step 22

Clean the brake disk surface. Use a brake cleaner.

AUTODOC recommends:
Replacement: anti roll bar links – VW JETTA III (1K2). After applying the spray, wait a few minutes.
Step 23

Install the wheel.

AUTODOC recommends:
Important! Hold the wheel while screwing in the fastening bolts. VW JETTA III (1K2)
Step 24

Screw in the wheel bolts. Use wheel impact socket #17.
Step 25

Lower the car and working in a cross order, tighten the wheel bolts. Use wheel impact socket #17. Use a torque wrench. Tighten it to 120 Nm torque.
Step 26

Remove the jacks and chocks.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the VW Jetta Mk5 (1K) model.

Browse tyres

How to change front strut mount on VW Jetta Mk5 (1K) – replacement guide

Free download PDF
4.14 MB
How to change rear suspension lower trailing arm on VW Jetta Mk5 (1K) – replacement guide

Free download PDF
1.66 MB
How to change rear suspension lower control arm on VW Jetta Mk5 (1K) – replacement guide

Free download PDF
1.62 MB
How to change track rod end on VW Jetta Mk5 (1K) – replacement guide

Free download PDF
2.22 MB
How to change front lower arm on VW Jetta Mk5 (1K) – replacement guide

Free download PDF
2.53 MB
How to change rear wheel bearing on VW Jetta Mk5 (1K) – replacement guide

Free download PDF
2.22 MB

How to change front anti roll bar links on VW Jetta Mk5 (1K) – replacement guide

Free download PDF
1.15 MB
How to change rear anti roll bar links on VW Jetta IV (162, 163, AV3, AV2) – replacement guide

Free download PDF
1.49 MB
How to change front anti roll bar links on VW Jetta IV (162, 163, AV3, AV2) – replacement guide

Free download PDF
1.15 MB
How to change front anti roll bar links on VW Jetta Mk2 (19E, 1G2, 165) – replacement guide

Free download PDF
1.03 MB
How to change front anti roll bar links on VW Jetta Mk7 Saloon (BU3) – replacement guide

Free download PDF
1.12 MB
How to change anti roll bar links on a car – replacement tutorial

Universal

Free download PDF
972.8 KB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

DIY valve cover restoration | AUTODOC tips

6K views

Published on: 29/06/2023
Important differences between car tools | AUTODOC tips

7K views

Published on: 16/12/2021
Coolant comparison test | AUTODOC

4K views

Published on: 13/10/2022
DIY car soundproofing | AUTODOC tips

76K views

Published on: 15/04/2021