Important!
This replacement procedure can be used for:
BMW Z3 Roadster (E36) M3.2 View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Ignition Coil for Z3 Roadster (E36) and other BMW models
Alternative products
How to change Ignition coil on BMW Z3 Roadster 1.8i – step-by-step instructions for straightforward car repair Ignition coil
Tools
Replacement: ignition coil – BMW Z3 (E36). Tools you might need:
Electronic spray
High-temperature anti-seize lubricant
HEX bit no.H5.
Drive socket # 8
Ratchet wrench
Flat Screwdriver
Fender cover
Replacement: ignition coil – BMW Z3 (E36). AUTODOC recommends:
  • The replacement procedure is the same for the ignition coils of all cylinders.
  • All work should be done with the engine stopped.
Replacement: ignition coil – BMW Z3 (E36). Take the following steps:
  1. Step 1
    Open the hood.
    Step 2
    Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
    Step 3
    How to change Ignition Coil on BMW Z3 Roadster 1995 - free PDF and video manuals
    Unscrew the fasteners of the cabin filter housing cover. Use a drive socket #8. Use a ratchet wrench.
  2. Step 4
    How to replace BMW Z3 Roadster (E36) 1.8i 1996 Ignition Coil - step-by-step manuals and video guides
    Remove the cabin filter housing cover.
    AUTODOC recommends:
    Replacement: ignition coil – BMW Z3 (E36). Do not use excessive force when removing the part as this may damage it.
  3. Step 5
    BMW Z3 Roadster 1.9i 1997 Ignition Coil replacement: free workshop manuals
    Remove the wiper arm covers.
  4. Step 6
    Changing Ignition Coil on BMW Z3 Roadster (E36) 2.0i 1998 by yourself
    Detach the connectors from the climate control sensors.
  5. Step 7
    Remove the climate control sensors.
    Step 8
    How to remove BMW Z3 3.0i 1999 Ignition Coil - online easy-to-follow instructions
    Unscrew the fasteners of the lower part of the scuttle panel. Use a drive socket #8. Use a ratchet wrench.
  6. Step 9
    How to replace Ignition Coil on BMW Z3 Roadster (E36) 2000: download PDF manuals and video instructions
    Detach the cable duct from the upper part of the microfilter housing. Use a flat screwdriver.
  7. Step 10
    How hard is it to do yourself: Ignition Coil replacement on BMW Z3 Roadster M3.2 2001 - download illustrated guide
    Remove the lower part of the scuttle panel.
  8. Step 11
    Need to know how to renew Ignition Coil on BMW Z3 2002? This free workshop manual will help you to do it yourself
    Unscrew the engine cover fastener. Use HEX No.H5. Use a ratchet wrench.
  9. Step 12
    Changing of Ignition Coil on BMW Z3 Roadster 2003 won't be an issue if you follow this illustrated step-by-step guide
    Remove the engine cover.
    Replacement: ignition coil – BMW Z3 (E36). Tip:
    Do not apply excessive force when removing the part. Otherwise you may damage it.
  10. Step 13
    BMW Z3 1.9i Ignition Coil replacement: online guides and video tutorials
    Detach the connector from the ignition coil.
  11. Step 14
    Replacing Ignition Coil on BMW Z3 Roadster 1996 1.8i by yourself
    Treat the ignition coil connector with electronic spray. The spray will protect the electrical contacts from corrosion, oxidation, and will reduce the contact resistance.
  12. Step 15
    Z3 Roadster (E36) 3.0i 1997 Ignition Coil DIY replacement workshop manual
    Take out the ignition coil from the spark plug well.
  13. Step 16
    How to change Ignition Coil on BMW Z3 Roadster (E36) 1998 - tips and tricks
    Treat the ignition coil tips. Use high-temperature grease. Use a flat screwdriver.
  14. Step 17
    Step-by-step recommendations for DIY replacement BMW Z3 Roadster 1999 3.0i Ignition Coil
    Install the new ignition coil to the spark plug well. Make sure you hear a click indicating that it is locked in place.
  15. Step 18
    DIY replacement of Ignition Coil on BMW Z3 Roadster (E36) 2.8i 2000 is not an issue anymore with our step-by-step tutorial
    Plug in the ignition coil connector.
  16. Step 19
    How to change Ignition Coil on BMW Z3 Roadster 1995 - free PDF and video manuals
    Install the engine cover and secure it.
    Replacement: ignition coil – BMW Z3 (E36). AUTODOC experts recommend:
    Make sure the engine cover is properly seated. It should not be displaced with respect to the guiding fasteners.Do not apply excessive force when installing the part. Otherwise you may damage the fasteners.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?

Find out which tyre and wheel sizes are compatible with the BMW Z3 Roadster (E36) model

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY BMW Z3 Roadster (E36) Ignition Coil replacement - online guide
Tips & tricks for your BMW Z3 Roadster (E36)
View more
  • How to change Coil pack on BMW Z3 Roadster (E36) 2.8i - replacement tricks
    #TPMS Explained: Why Your Light is On and How to Respond Safely
  • Changing Ignition coil pack BMW Z3 Roadster 1.8i - Replacement Tips
    Understanding Car Tools: The Key Differences You Need to Know | AUTODOC tips
  • Maintenance Hacks - BMW Z3 Roadster (E36) 1.9i Ignition coils replacement guide
    Top 5 brake repair mistakes | AUTODOC tips
  • Replace Coil packs on BMW Z3 Roadster - free video tips
    5 mistakes made when washing the engine | AUTODOC tips
Autodoc CLUB App icon
Time to replace parts? Get even better deals in our Shop app.
BMW Z3 Roadster (E36) Ignition Coil replace by yourself - Scan QR-code and download AUTODOC CLUB app
SCAN ME