Recommended replacement interval for the part category Glow plug : 30000 km

Important!

This replacement procedure can be used for:
VW CRAFTER Platform/Chassis (SZ_) 2.0 TDI RWD, VW CRAFTER Platform/Chassis (SZ_) 2.0 TDI 4motion, VW CRAFTER Platform/Chassis (SZ_) 2.0 TDI 4motion, VW CRAFTER Platform/Chassis (SZ_) 2.0 TDI RWD, VW CRAFTER Platform/Chassis (SZ_) 2.0 TDI RWD, VW CRAFTER Platform/Chassis (SZ_) 2.0 TDI RWD, VW CRAFTER Platform/Chassis (SZ_) 2.0 TDI, VW CRAFTER Platform/Chassis (SZ_) 2.0 TDI, VW CRAFTER Platform/Chassis (SZ_) 2.0 TDI … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Glow Plugs for CRAFTER Platform/Chassis (SZ_) and other VW models

Glow plug

        Glow plug for Crafter Platform / Chassis (SZ) Diesel (102 hp)
      
        Glow plug for Crafter Platform / Chassis (SZ) Diesel (140 hp)
      
        Glow plug for Crafter Platform / Chassis (SZ) Diesel (177 hp)
      
        Glow plug for Crafter Platform / Chassis (SZ) Diesel (122 hp)
      
        Glow plug for Crafter Platform / Chassis (SZ) Diesel (177 hp)
      
        Glow plug for Crafter Platform / Chassis (SZ) Diesel (140 hp)
      
        Glow plug for Crafter Platform / Chassis (SZ) Diesel (140 hp)
      
        Glow plug for Crafter Platform / Chassis (SZ) Diesel (177 hp)
      
        Glow plug for Crafter Platform / Chassis (SZ) Diesel (109 hp)

Replacement: glow plugs – VW CRAFTER Platform/Chassis (SZ_). Tools you might need:

                        WD-40 spray
                      
                        Electronic spray
                      
                        High-temperature ceramic grease
                      
                        Torque wrench
                      
                        Spark plug socket # 10
                      
                        Torx bit T27
                      
                        Ratchet wrench
                      
                        Flat screwdriver
                      
                        Needle nose pliers
                      
                        Fender cover

Buy tools

Replacement: glow plugs – VW CRAFTER Platform/Chassis (SZ_). AUTODOC experts recommend:

The replacement procedure is identical for all glow plugs.
Wear gloves to protect your hands from hot surfaces.
Replacement: glow plugs – VW CRAFTER Platform/Chassis (SZ_). Recommended sequence of steps:

Carry out replacement in the following order:

Step 1

Open the bonnet.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Before getting down to work, start the engine and let it warm up to operating temperature.

Step 4

Shut off the engine.

Step 5

Unscrew the bracket for the engine pipes. Use Torx T27. Use a ratchet wrench.
Step 6

Detach the engine wiring harness. Use a flat screwdriver.
Step 7

Detach the engine wiring harness connectors. Use a flat screwdriver.
Step 8

Detach the glow plug wiring connectors. Use needle nose pliers.
Step 9

Clean dirt, dust and debris from inside the spark plug wells.
Step 10

Treat the glow plugs. Use WD-40 spray.
Step 11

Unscrew the glow plugs. Use the spark plug socket #10. Use a torque wrench.
Step 12

Clean dirt, dust and debris from inside the spark plug wells.
Step 13

Remove the glow plugs. Use the spark plug socket #10. Use needle nose pliers.
Step 14

Treat the glow plugs. Use high-temperature ceramic grease.

Please note!
Do not touch the heating element as fingerprints may cause malfunction.
Step 15

Install new glow plugs to their mounting seats. Use needle nose pliers.
Step 16

Tighten the glow plugs. Use the spark plug socket #10. Use a torque wrench. Tighten it to 18 nm torque.

Replacement: glow plugs – VW CRAFTER Platform/Chassis (SZ_). Tip from AUTODOC experts:
Don't tighten the plugs with excessive force. Exceeding tightening torque can damage the thread connection. Be careful when working with a spark plug wrench. Its skewing can cause damage to the threaded connection.
Step 17

Attach the glow plug wiring connectors.
Step 18

Treat the engine wiring harness connectors. Use dielectric grease.
Step 19

Attach the engine wiring harness connectors.
Step 20

Attach the engine wiring harness.

Step 21

Screw in the bracket for the engine pipes. Use Torx T27. Use a torque wrench. Tighten it to 7 nm torque.

Step 22

Run the engine for a few minutes. This is necessary in order to make sure that the component operates properly.

Step 23

Shut off the engine.

Step 24

Remove the fender protection cover.

Step 25

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the VW Crafter Platform / Chassis (SZ) model.

Browse tyres

How to change pollen filter on VW Crafter Platform / Chassis (SZ) – replacement guide

Free download PDF
768 KB
How to change headlight bulb on VW Crafter Platform / Chassis (SZ) – replacement guide

Free download PDF
1.48 MB
How to change front ABS sensor on VW Crafter Platform / Chassis (SZ) – replacement guide

Free download PDF
1.28 MB
How to change engine thermostat on VW Passat B7 saloon – replacement guide

Free download PDF
4.1 MB
How to change fuel filter on VW Polo 9N – replacement guide

Free download PDF
1.75 MB
How to change engine oil and filter on VW Polo 9N – replacement guide

Free download PDF
2.34 MB

How to change glow plugs on VW CRAFTER 30-50 Box (2E_) – replacement guide

Free download PDF
1.2 MB
How to change glow plugs on VW Crafter Van (SY_, SX_) – replacement guide

Free download PDF
1.2 MB
How to change glow plugs on VW CRAFTER 30-50 Platform/Chassis (2F_) – replacement guide

Free download PDF
1.2 MB
How to change glow plugs on VW CRAFTER 30-35 Bus (2E_) – replacement guide

Free download PDF
1.2 MB
How to change glow plugs on VW CRAFTER Bus (SY_) – replacement guide

Free download PDF
1.2 MB
How to change glow plugs on a car – replacement tutorial

Universal

Free download PDF
1.62 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to choose the right engine oil for your car | AUTODOC

8K views

Published on: 01/07/2020
Checking the starter without removing it | AUTODOC tips

19K views

Published on: 01/12/2020
How to remove scratches from car plastic | AUTODOC tips

100K views

Published on: 15/12/2022
How to restore a steering wheel | AUTODOC tips

32K views

Published on: 17/02/2022