Important!

This replacement procedure can be used for:
RENAULT GRAND SCÉNIC II (JM0/1_) 1.6, RENAULT GRAND SCÉNIC II (JM0/1_) 2.0, RENAULT GRAND SCÉNIC II (JM0/1_) 1.5 dCi (JM02, JM13), RENAULT GRAND SCÉNIC II (JM0/1_) 1.9 dCi (JM0G, JM12, JM1G, JM2C), RENAULT GRAND SCÉNIC II (JM0/1_) 2.0, RENAULT GRAND SCÉNIC II (JM0/1_) 1.9 dCi (JM15), RENAULT GRAND SCÉNIC II (JM0/1_) 1.9 dCi (JM14), RENAULT GRAND SCÉNIC II (JM0/1_) 2.0 dCi (JM1K), RENAULT GRAND SCÉNIC II (JM0/1_) 1.6, RENAULT GRAND SCÉNIC II (JM0/1_) 1.5 dCi (JM1E), RENAULT GRAND SCÉNIC II (JM0/1_) 1.6, RENAULT GRAND SCÉNIC II (JM0/1_) 1.6 Flex, RENAULT GRAND SCÉNIC II (JM0/1_) 1.9 dCi, RENAULT GRAND SCÉNIC II (JM0/1_) 1.5 dCi … View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Control Arm for GRAND SCÉNIC II (JM0/1_) and other RENAULT models

Suspension arm

        Suspension arm for Grand Scénic II (JM) Petrol (113 hp)
      
        Suspension arm for Grand Scénic II (JM) Petrol (135 hp)
      
        Suspension arm for Grand Scénic II (JM) Diesel (101 hp)
      
        Suspension arm for Grand Scénic II (JM) Diesel (120 hp)
      
        Suspension arm for Grand Scénic II (JM) Petrol (163 hp)
      
        Suspension arm for Grand Scénic II (JM) Diesel (110 hp)
      
        Suspension arm for Grand Scénic II (JM) Diesel (131 hp)
      
        Suspension arm for Grand Scénic II (JM) Diesel (150 hp)
      
        Suspension arm for Grand Scénic II (JM) Petrol (105 hp)

Replacement: front lower arm – RENAULT GRAND SCÉNIC II (JM0/1_). Tools you might need:

                        Wire brush
                      
                        WD-40 spray
                      
                        Copper grease 
                      
                        Combination spanner #16
                      
                        Combination spanner #18
                      
                        Drive socket # 12 
                      
                        Drive socket # 13 
                      
                        Drive socket # 16 
                      
                        Drive socket # E16 
                      
                        Drive socket # 18 
                      
                        Torx bit T20
                      
                        Wheel impact socket #19
                      
                        Shock absorber socket
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Clip removal tool
                      
                        Pin punch
                      
                        Hammer
                      
                        Crow bar
                      
                        Rubber mallet
                      
                        Hydraulic transmission jack
                      
                        Fender cover
                      
                        Wheel chock

Buy tools

Replacement: front lower arm – RENAULT GRAND SCÉNIC II (JM0/1_). AUTODOC experts recommend:

The replacement procedure is identical for the left and right lower control arms.
All work should be done with the engine stopped.

Replacement: front lower arm – RENAULT GRAND SCÉNIC II (JM0/1_). Use the following procedure:

Step 1

Open the bonnet.

Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.

Step 3

Secure the wheels with chocks.
Step 4

Loosen the wheel mounting bolts. Use wheel impact socket #19.
Step 5

Raise the front of the car and secure on supports.

Step 6

Unscrew the wheel bolts.

AUTODOC recommends:
Important! Hold the wheel while unscrewing the fastening bolts. RENAULT GRAND SCÉNIC II (JM0/1_)
Step 7

Remove the wheel.
Step 8

Remove the lower sound insulation. Use a drive socket #12.
Step 9

Unscrew and remove the wheel arch cover fasteners. Use Torx T20. Use a clip removal tool.
Step 10

Remove the wheel arch cover.
Step 11

Clean the fasteners of the bumper reinforcement bar and of its bracket. Use a wire brush. Use WD-40 spray.

Replacement: front lower arm – RENAULT GRAND SCÉNIC II (JM0/1_). AUTODOC experts recommend:
After applying the spray, wait a few minutes.Wear protective goggles.
Step 12

Unscrew the fasteners of the bumper reinforcement bar bracket. Use a drive socket #13.
Step 13

Unscrew the fasteners connecting the bumper reinforcement bar to the subframe. Use a drive socket #13. Use a ratchet wrench.
Step 14

Support the lower radiator support to prevent it from falling when removing the bumper reinforcement bar. Use a hydraulic transmission jack.
Step 15

Loosen the fastener connecting the bumper reinforcement bar to the lower radiator support. Use a drive socket #18. Use a ratchet wrench.
Step 16

Detach and pull aside the bumper reinforcement bar. Use a crowbar.
Step 17

Clean the fastener connecting the ball joint to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 18

Clean the fasteners connecting the control arm to the subframe. Use a wire brush. Use WD-40 spray.
Step 19

Detach the ABS sensor wiring from the suspension control arm. Use a clip removal tool.
Step 20

Unscrew the ball joint fastening to the steering knuckle. Use a drive socket #16. Use a combination spanner #18. Use a ratchet wrench.
Step 21

Remove the fastening bolt. Use a hammer. Use a pin punch.
Step 22

Unscrew the front arm fastener. Use a drive socket #E16. Use a combination spanner #18. Use a ratchet wrench.
Step 23

Remove the fastening bolt. Use a crowbar.
Step 24

Unscrew the rear arm fastener. Use a drive socket #18. Use a combination spanner #18. Use a ratchet wrench.
Step 25

Release the fastener connecting the ball joint to the steering knuckle. Use a special drive socket to remove the shock absorber.
Step 26

Disconnect the ball joint from the steering knuckle. Use a crowbar.
Step 27

Remove the arm. Use a crowbar.
Step 28

Clean the mounting seats and the thread of the suspension arm. Use a wire brush.
Step 29

Install a new arm.
Step 30

Connect the ball joint to the steering knuckle.
Step 31

Install the control arm fasteners.
Step 32

Screw the rear arm fastener. Use a drive socket #18.
Step 33

Install the front fastener of the arm. Use a crowbar. Use a rubber mallet.
Step 34

Screw the front arm fastener. Use a drive socket #E16. Use a combination spanner #18. Use a ratchet wrench.
Step 35

Install the bumper reinforcement bar. Use a crowbar.
Step 36

Screw in the fastener connecting the bumper reinforcement bar to the lower radiator support.
Step 37

Screw in the fastener connecting the bumper reinforcement bar to the subframe.
Step 38

Remove the support from under the lower radiator support.

AUTODOC recommends:
Replacement: front lower arm – RENAULT GRAND SCÉNIC II (JM0/1_). Lower the transmission jack smoothly, without jerks, to avoid damaging components and mechanisms.
Step 39

Support the arm. Use a hydraulic transmission jack.
Step 40

Tighten the rear fastener connecting the arm to the body subframe. Use a drive socket #18. Use a combination spanner #18. Use a torque wrench. Tighten it to 105 nm torque.
Step 41

Tighten the front fastener connecting the control arm to the subframe. Use a combination spanner #16. Use a combination spanner #18. Use a torque wrench. Tighten it to 105 nm torque.
Step 42

Tighten the ball joint fastener. Use a drive socket #16. Use a combination spanner #18. Use a torque wrench. Tighten it to 62 nm torque.
Step 43

Remove the support from under the arm.

Replacement: front lower arm – RENAULT GRAND SCÉNIC II (JM0/1_). Professionals recommend:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 44

Tighten the fastener connecting the bumper reinforcement bar to the subframe. Use a drive socket #13. Use a ratchet wrench.
Step 45

Tighten the fastener connecting the bumper reinforcement bar to the lower radiator support. Use a drive socket #18. Use a torque wrench. Tighten it to 75 nm torque.
Step 46

Treat all joints of the arm. Use copper grease.
Step 47

Screw in the fastener of the bumper reinforcement bar bracket. Use a drive socket #13.
Step 48

Connect the ABS sensor wiring.
Step 49

Install the wheel arch cover to its mounting seat.
Step 50

Install and tighten the wheel arch cover fasteners. Use Torx T20.
Step 51

Install the lower sound insulation.
Step 52

Screw in the fasteners of the lower sound insulation. Use a drive socket #12.
Step 53

Clean the wheel rim mounting seat. Use a wire brush. Treat the contacting surface. Use copper grease.
Step 54

Install the wheel.

Replacement: front lower arm – RENAULT GRAND SCÉNIC II (JM0/1_). Tip from AUTODOC experts:
To avoid injury, hold up the wheel when screwing in the fastening bolts.
Step 55

Screw in the wheel bolts. Use wheel impact socket #19.
Step 56

Lower the car and working in a cross order, tighten the wheel bolts. Use a torque wrench. Tighten it to 110 nm torque.
Step 57

Remove the jacks and chocks.

Step 58

Remove the fender protection cover.

Step 59

Close the hood.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Searching for the right tyres?

Find out which tyre and wheel sizes are compatible with the RENAULT Grand Scénic II (JM) model.

Browse tyres

How to change front strut mount on RENAULT Grand Scénic II (JM) – replacement guide

Free download PDF
3.33 MB
How to change front anti roll bar links on RENAULT Grand Scénic II (JM) – replacement guide

Free download PDF
1.98 MB
How to change front brake pads on RENAULT GRAND SCÉNIC II (JM0/1_) – replacement guide

Free download PDF
1.51 MB
How to change rear brake pads on RENAULT GRAND SCÉNIC II (JM0/1_) – replacement guide

Free download PDF
1.37 MB
How to change rear brake discs on RENAULT GRAND SCÉNIC II (JM0/1_) – replacement guide

Free download PDF
2.11 MB
How to change front brake discs on RENAULT Grand Scénic II (JM) – replacement guide

Free download PDF
2.6 MB

How to change control arm on a car – replacement tutorial

Universal

Free download PDF
1.07 MB
How to change front lower arm on Renault Clio 3 – replacement guide

Free download PDF
2.57 MB
How to change front lower arm on Renault Scenic 2 – replacement guide

Free download PDF
3.34 MB
How to change front lower arm on Renault Clio 2 – replacement guide

Free download PDF
2.9 MB
How to change front lower arm on Renault Twingo C06 – replacement guide

Free download PDF
1.92 MB
How to change front lower arm on Renault Megane 2 – replacement guide

Free download PDF
3.3 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

How to save when buying car parts

2K views

Published on: 03/02/2022
How to start a car after a long idle period | AUTODOC tips

6K views

Published on: 20/05/2021
Petrol or diesel? What's the difference between these engines? | AUTODOC

4K views

Published on: 04/05/2021
How to wash your car in winter | AUTODOC tips

3K views

Published on: 31/01/2024