Important!

This replacement procedure can be used for:
FORD Transit Mk6 Box (V347, V348, FA) 2.2 TDCi, FORD Transit Mk6 Box (V347, V348, FA) 2.2 TDCi, FORD Transit Mk6 Box (V347, V348, FA) 2.2 TDCi, FORD Transit Mk6 Box (V347, V348, FA) 2.2 TDCi, FORD Transit Mk6 Box (V347, V348, FA) 2.4 TDCi RWD, FORD Transit Mk6 Box (V347, V348, FA) 2.4 TDCi RWD, FORD Transit Mk6 Box (V347, V348, FA) 2.2 TDCi, FORD Transit Mk6 Box (V347, V348, FA) 2.4 TDCi RWD, FORD Transit Mk6 Box (V347, V348, FA) 2.3 16V RWD, FORD Transit Mk6 Box (V347, V348, FA) 3.2 TDCi RWD, FORD Transit Mk6 Box (V347, V348, FA) 2.2 TDCi, FORD Transit Mk6 Box (V347, V348, FA) 2.2 TDCi, FORD Transit Mk6 Box (V347, V348, FA) 2.4 TDCi 4x4 … View more

The steps may slightly vary depending on the car design.

How to change a front suspension strut on the FORD TRANSIT MK7 [AUTODOC TUTORIAL]

Alternative products

Coil spring

Replacement: coil springs – Ford Transit Mk7 van. Tools you'll need:

                      Wire brush
                    
                      WD-40 spray
                    
                      All-purpose cleaning spray
                    
                      Ceramic grease
                    
                      Torque wrench
                    
                      19 mm combination spanner
                    
                      13 mm socket
                    
                      15 mm socket
                    
                      18 mm socket
                    
                      19 mm socket
                    
                      24 mm socket
                    
                      36 mm socket
                    
                      18 mm strut nut socket
                    
                      H5 hex bit
                    
                      H6 hex extension bar
                    
                      21 mm wheel impact socket
                    
                      Ratchet wrench or power tool for removal/installation of threaded fasteners
                    
                      Tommy bar
                    
                      Mounting lever
                    
                      Long nose pliers
                    
                      Telescoping magnetic pick-up tool 
                    
                      Pin punch
                    
                      Hammer
                    
                      Rubber mallet
                    
                      Ball joint separator
                    
                      Stationary spring compressor
                    
                      Transmission jack or a second vehicle jack
                    
                      Car lift or jack with jack stands, and wheel chocks

Buy tools

Replacement: coil springs – Ford Transit Mk7 van. AUTODOC recommends:

The struts, coil springs, and strut mounts of the front suspension should be replaced in pairs.
The replacement procedure is identical for the right and left struts, coil springs, and strut mounts of the front suspension, with the exception of the steps for accessing the fasteners of the left and right strut mounts.
Please note: all work on the car – Ford Transit Mk7 van – should be done with the engine switched off.

Carry out the replacement steps as follows:

Step 1

Open the car door.
Step 2

Open the glove box.
Step 3

Press down on the glove box retaining tabs to detach it.
Step 4

Remove the glove box.
Step 5

Fold back the insulation that covers the strut mount fasteners.
Step 6

Clean the fasteners of the top strut mount. Use a wire brush. Use WD-40 spray.
Step 7

Loosen the strut mount fasteners. Use a 13 mm socket. Use a ratchet wrench.

Warning!
Do not unscrew the nuts completely.
Step 8

Secure the wheels with chocks.
Step 9

Remove the wheel centre cap.

Step 10

Loosen the wheel nuts. Use a 21 mm wheel impact socket. Use a tommy bar.
Step 11

Remove the cotter pin that secures the axle fastener. Use a mounting lever. Use long nose pliers.
Step 12

Remove the castle cover from the axle nut.
Step 13

Clean the axle nut. Use a wire brush. Use WD-40 spray.
Step 14

Loosen the axle nut. Use a 36 mm socket. Use a tommy bar.
Step 15

Raise the vehicle.

Replacement: coil springs – Ford Transit Mk7 van. AUTODOC experts recommend:
If you are using a jack, make sure the car is parked on a hard, flat surface.Make sure to additionally secure the car with jack stands.
Step 16

Unscrew the wheel nuts.

Replacement: coil springs – Ford Transit Mk7 van. Tip:
To avoid injury, hold up the wheel when unscrewing the nuts.
Step 17

Remove the wheel.
Step 18

Clean the fastener that connects the anti-roll bar link to the suspension strut. Use a wire brush. Use WD-40 spray.
Step 19

Clean the fastener of the ABS sensor cable bracket. Use a wire brush. Use WD-40 spray.

Step 20

Clean the fastener connecting the suspension strut to the steering knuckle. Use a wire brush. Use WD-40 spray.
Step 21

Unscrew the fastener of the ABS sensor cable bracket. Use an 18 mm socket. Use a ratchet wrench.
Step 22

Detach the ABS sensor cable bracket from the suspension strut.
Step 23

Unscrew the fastener connecting the anti-roll bar link to the suspension strut. Use a 19 mm combination spanner. Use an H5 hex bit. Use a ratchet wrench.
Step 24

Disconnect the anti-roll bar link from the suspension strut.
Step 25

Unscrew the axle nut. Use a 36 mm socket. Use a ratchet wrench.
Step 26

Remove the axle washer. Use a telescoping magnetic pick-up tool.
Step 27

Support the suspension arm. Use a transmission jack or one more vehicle jack.
Step 28

Detach the CV axle from the steering knuckle. Use a pin punch. Use a hammer.
Step 29

Remove the support from under the suspension arm.

AUTODOC recommendation:
Lower the transmission or vehicle jack smoothly without jerking it to avoid damaging the vehicle assemblies and mechanisms.
Step 30

Clean the fastener that connects the ball joint to the suspension arm. Use a wire brush. Use WD-40 spray.
Step 31

Unscrew the fastener connecting the ball joint to the suspension arm. Use a 24 mm socket. Use a ratchet wrench.
Step 32

Support the steering knuckle. Use a transmission jack or one more vehicle jack.
Step 33

Disconnect the ball joint from the suspension arm. Use a ball joint separator. Use a mounting lever.
Step 34

Remove the support from under the steering knuckle.

Step 35

Release the ball joint from the suspension arm by pulling down the suspension arm with the mounting lever.

Step 36

After releasing the ball joint, move the steering knuckle a little to the side and carefully return the suspension arm to its original position.

Step 37

Support the steering knuckle again.

Step 38

Remove the CV axle from the steering knuckle.

Step 39

Tie the CV axle to the car body with a wire.

Replacement: coil springs – Ford Transit Mk7 van. Tip from AUTODOC:
Make sure that the CV axle is not hanging down.
Step 40

Unscrew the lower fastener of the suspension strut. Use a 15 mm socket. Use a ratchet wrench.
Step 41

Remove the fastening bolt.
Step 42

Disconnect the steering knuckle from the suspension strut. Use a rubber mallet. Use a transmission jack or one more vehicle jack.

Warning!
Make sure that the steering knuckle is not hanging loose on the brake hose or electric cable.
Step 43

Unscrew the fasteners of the suspension strut mount.

Replacement: coil springs – Ford Transit Mk7 van. Professionals recommend:
To avoid injuries, hold the strut when undoing the fasteners.
Step 44

Remove the suspension strut assembly.
Step 45

Clean the mounting seats of the suspension strut. Use a wire brush. Use an all-purpose cleaning spray.
Step 46

Clean the fastener on the anti-roll bar link. Use a wire brush. Use an all-purpose cleaning spray.
Step 47

Clean the splines of the CV axle joint. Use a wire brush. Use an all-purpose cleaning spray.
Step 48

Depending on what part you are replacing, you may have to disassemble the suspension strut. But if you use all new components, then you will not need to disassemble the old strut. In this case, a stationary spring compressor will only be required to assemble a new strut if its parts were purchased separately.

Step 49

Set the suspension strut assembly on the stationary spring compressor.

Replacement: coil springs – Ford Transit Mk7 van. Tip from AUTODOC experts:
When using a stationary spring compressor, the spring coils must be securely clamped, compressing the spring from both ends.Make sure the spring is in the correct position.Make sure that the compressor jaws are tightly engaged onto the coils.
Step 50

Compress the spring.
Step 51

Clean the top part of the strut piston rod. Use a wire brush. Use WD-40 spray.
Step 52

Unscrew the strut piston rod nut. Use an 18 mm strut nut socket. Use an H6 hex extension bar. Use a ratchet wrench.
Step 53

Remove the top strut mount.
Step 54

Release the spring.
Step 55

Remove the mount bearing and the bump stop.
Step 56

Remove the spring.
Step 57

Remove the dust boot.

Step 58

Install a new spring on the strut.
Step 59

Install a dust boot, bump stop, and mount bearing.
Step 60

Compress the spring.
Step 61

Install a top strut mount.
Step 62

Install and tighten the strut piston rod nut. Use an 18 mm strut nut socket. Use an H6 hex extension bar. Use a torque wrench. Tightening torque: 70 N·m.
Step 63

Release the spring.
Step 64

Remove the strut assembly from the spring compressor.
Step 65

Install the strut assembly into the wheel arch.
Step 66

Screw on the strut mount fasteners. Do not tighten them.

Caution!
To avoid injuries, hold the strut when screwing the fastening nuts on.
Step 67

Secure the strut on the steering knuckle. Use a transmission jack or one more vehicle jack.
Step 68

Install and screw in the fastening bolt.
Step 69

Install the CV axle.

Warning!
When reassembling, use a new axle nut kit: a washer, a nut, a castle cover, and a cotter pin.
Step 70

Install the axle washer.
Step 71

Screw on the axle nut. Use a 36 mm socket. Use a ratchet wrench.
Step 72

Clean the ball joint mounting seat. Use a wire brush. Use WD-40 spray.
Step 73

Attach the ball joint to the suspension arm and screw on the fastening nut. Use a mounting lever.
Step 74

Ιnstall the anti-roll bar link and screw on the fastening nut.
Step 75

Install the ABS sensor cable bracket and screw on the fastening nut.
Step 76

Tighten the fastener connecting the anti-roll bar link to the suspension strut. Use a 19 mm socket. Use a torque wrench. Tightening torque: 55 N·m.
Step 77

Tighten the fastener of the ABS sensor cable bracket. Use an 18 mm socket. Use a torque wrench. Tightening torque: 45 N·m.
Step 78

Jack up the steering knuckle.

Step 79

Tighten the lower fastener of the suspension strut. Use an 18 mm socket. Use a torque wrench. Tightening torque: 100 N·m + 180°.

Important!
Make sure to use new fasteners.
Step 80

Remove the support from under the steering knuckle.

Replacement: coil springs – Ford Transit Mk7 van. AUTODOC recommends:
Lower the transmission or vehicle jack smoothly without jerking it to avoid damaging the vehicle assemblies and mechanisms.
Step 81

Tighten the fastener that connects the suspension arm to the ball joint. Use a 24 mm socket. Use a torque wrench. Tightening torque: 150 N·m.
Step 82

Clean the wheel rim mounting seat. Use a wire brush. Use an all-purpose cleaning spray.
Step 83

Treat the wheel hub surface that contacts the wheel rim. Use ceramic grease.
Step 84

Install the wheel.

Caution!
To avoid injury, hold up the wheel when screwing on the fastening nuts.
Step 85

Screw on the wheel nuts. Use a 21 mm wheel impact socket. Use a ratchet wrench.
Step 86

Lower the car and tighten the wheel nuts in a criss-cross pattern. Use a 21 mm wheel impact socket. Use a torque wrench. Tightening torque: 200 N·m.
Step 87

Tighten the axle nut. Use a 36 mm socket. Use a torque wrench. Tightening torque: 320 N·m.
Step 88

Install the castle cover on the axle nut.
Step 89

Install the cotter pin. Use a mounting lever.
Step 90

Install the wheel centre cap.

Step 91

Remove the jack, jack stands, and wheel chocks.

Step 92

Tighten the strut mount fasteners. Use a 13 mm socket. Use a torque wrench. Tightening torque: 30 N·m.
Step 93

Put the insulation that covers the strut mount fasteners back in place.
Step 94

Install the glove box by pressing down on its retaining tabs.
Step 95

Close the glove box.
Step 96

Close the car door.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

Need New Tyres?

Find out which tyre and wheel sizes are compatible with the FORD Transit Mk6 Van (V347, V348) model

Ford Transit Mk6 Van tyre size

How to change rear shock absorbers on Ford Transit Mk7 van – replacement guide

Free download PDF 1.66 MB
How to change front suspension strut on Ford Transit Mk7 van – replacement guide

Free download PDF 4.63 MB
How to change rear brake pads on Ford Transit Mk7 van – replacement guide

Free download PDF 2.02 MB
How to change front brake pads on Ford Transit Mk7 van – replacement guide

Free download PDF 1.96 MB
How to change front brake discs on Ford Transit Mk7 van – replacement guide

Free download PDF 3.89 MB
How to change front wheel bearing on Ford Transit Mk7 van – replacement guide

Free download PDF 3.24 MB

How to change front coil springs on FORD Transit Mk6 Minibus (V347, V348) – replacement guide

Free download PDF 4.47 MB
How to change front coil springs on FORD Transit Mk6 Caja / Chasis (V347, V348) – replacement guide

Free download PDF 4.53 MB
How to change front coil springs on FORD Transit Mk6 Tourneo – replacement guide

Free download PDF 4.52 MB
How to change coil springs on a car – replacement tutorial

Universal

Free download PDF 1.91 MB
How to change front coil springs on Ford Fiesta JA8 – replacement guide

Free download PDF 3.47 MB
How to change front coil springs on Ford Fiesta V JH JD – replacement guide

Free download PDF 5.1 MB

Unlock your car maintenance assistant!

Track expenses, manage logs, schedule replacements, and more.

DIY jack restoration | AUTODOC tips

33K views

Published on: 22/09/2022
Prevent Breakdowns: Key Car Checks After Winter | AUTODOC Guide

3K views

Published on: 23/03/2023
How to remove scratches from car plastic | AUTODOC tips

198K views

Published on: 15/12/2022
How an automatic gearbox works: the ZF 8HP

136K views

Published on: 12/03/2026