When to replace the Brake Pads on your HONDA CITY
Recommended replacement interval for the part category Brake pad set : 30000 km
Important!
This replacement procedure can be used for:
HONDA CITY Saloon (GM) 1.3 i-V TEC View more

The steps may slightly vary depending on the car design.

This video shows the replacement procedure of a similar car part on another vehicle

All the parts you need to replace – Brake Pads for CITY Saloon (GM) and other HONDA models
Tools
Replacement: brake pads – HONDA CITY Saloon (GM). List of the tools you'll need:
Wire brush
WD-40 spray
Brake cleaner
Anti-squeal paste
Copper grease
Drive socket # 12
Wheel impact socket #19
Brake caliper wind back tool
Ratchet wrench
Torque wrench
Crow bar
Wheel chock
Replacement: brake pads – HONDA CITY Saloon (GM). AUTODOC recommends:
  • Perform the replacement of brake pads in complete set for each axis. This provides effective braking.
  • The replacement procedure is identical for all brake pads on the same axle.
  • All work should be done with the engine stopped.
Replacement: brake pads – HONDA CITY Saloon (GM). Take the following steps:
  1. Step 1
    Open the bonnet. Unscrew the brake fluid reservoir cap.
    Step 2
    How to change Brake Pads on City GM 2008 - free PDF and video manuals
    Secure the wheels with chocks.
  2. Step 3
    How to replace HONDA CITY Saloon (GM) 1.3 i-V TEC 2009 Brake Pads - step-by-step manuals and video guides
    Loosen the wheel mounting bolts. Use wheel impact socket #19.
  3. Step 4
    Raise the front of the car and secure on supports.
    Step 5
    City GM 1.5 i-VTEC 2010 Brake Pads replacement: free workshop manuals
    Unscrew the wheel bolts.
    AUTODOC recommends:
    Important! Hold the wheel while unscrewing the fastening bolts. HONDA CITY Saloon (GM)
  4. Step 6
    Changing Brake Pads on HONDA CITY Saloon (GM) 1.5 Flex 2011 by yourself
    Remove the wheel.
  5. Step 7
    How to remove HONDA CITY 1.3 i-V TEC 2012 Brake Pads - online easy-to-follow instructions
    Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
  6. Step 8
    How to replace Brake Pads on HONDA CITY Saloon (GM) 2013: download PDF manuals and video instructions
    Spread the brake pads. Use a crowbar.
  7. Step 9
    How hard is it to do yourself: Brake Pads replacement on City GM 1.5 i-VTEC (GM2) 2014 - download illustrated guide
    Unscrew the brake caliper fastening. Use a drive socket #12. Use a ratchet wrench.
  8. Step 10
    Need to know how to renew Brake Pads on HONDA CITY 2015? This free workshop manual will help you to do it yourself
    Remove the brake caliper.
    Replacement: brake pads – HONDA CITY Saloon (GM). Professionals recommend:
    Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.Make sure that the brake caliper is not hanging on the brake hose.Don't press the brake pedal after the brake caliper has been removed. As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur. Check the brake caliper bracket, brake caliper guide pins and boots. Clean them. Replace, if necessary.
  9. Step 11
    Changing of Brake Pads on City GM 2016 won't be an issue if you follow this illustrated step-by-step guide
    Remove the brake pads. Use a crowbar.
    Replacement: brake pads – HONDA CITY Saloon (GM). AUTODOC experts recommend:
    Measure the brake disc thickness. Upon reaching the wear limit the part must be replaced.
  10. Step 12
    HONDA CITY 1.3 i-V TEC Brake Pads replacement: online guides and video tutorials
    Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
    AUTODOC recommends:
    Replacement: brake pads – HONDA CITY Saloon (GM). After applying the spray, wait a few minutes.
  11. Step 13
    Replacing Brake Pads on City GM 2018 1.3 i-V TEC by yourself
    Treat the brake caliper piston. Use a brake cleaner.
    Replacement: brake pads – HONDA CITY Saloon (GM). Tip from AUTODOC:
    After applying the spray, wait a few minutes.
  12. Step 14
    CITY Saloon (GM) 1.3 i-V TEC 2019 Brake Pads DIY replacement workshop manual
    Press in the brake caliper piston. Use brake caliper wind back tool.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
HONDA CITY Saloon (GM) Brake Pads replace by yourself - Scan QR-code and download AUTODOC CLUB app
Scan

To download the app:

  • - scan the QR code
  • - download from App Store
  • - download from Google Play
DIY HONDA CITY Saloon (GM) Brake Pads replacement - online guide
Tips & tricks for your HONDA CITY Saloon (GM)
View more
  • How to change Brake pad set on HONDA CITY Saloon (GM) 1.5 i-VTEC (GM2) - replacement tricks
    Things you should never do with an automatic transmission | AUTODOC tips
  • Changing Disc pads City GM 1.3 i-V TEC - Replacement Tips
    What to do if the belt squeals | AUTODOC tips
  • Maintenance Hacks - HONDA CITY Saloon (GM) 1.5 i-VTEC Brake pad kit replacement guide
    5 common car washing mistakes | AUTODOC tips
  • Replace Disc brake pads on City GM - free video tips
    How to save when buying car parts