Disclaimer
How to change front brake hose on VAUXHALL Vivaro Combi (X82) – replacement guide
downloads:
0
Views:
0
Recommended replacement interval for the part category Brake hose : 50000 km
Important!
This replacement procedure can be used for:
VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTI, VAUXHALL Vivaro Combi (X82) 1.6 CDTi … View more
The steps may slightly vary depending on the car design.
VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTi, VAUXHALL Vivaro Combi (X82) 1.6 CDTI, VAUXHALL Vivaro Combi (X82) 1.6 CDTi … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Brake Hose for Vivaro Combi (X82) and other VAUXHALL models
Alternative products
Brake hose
Wire brush
Wire bore brush
WD-40 spray
All-purpose cleaning spray
Brake caliper guide pin grease
Specialised brake caliper piston grease
Ceramic grease
Torque wrench
11 mm combination spanner
11 mm flare nut wrench
11 mm flare nut socket
14 mm combination spanner
14 mm flare nut socket
11 mm socket
13 mm socket
18 mm socket
19 mm wheel impact socket
Ratchet wrench or power tool for removal/installation of threaded fasteners
Tommy bar
Adjustable pliers
Mounting lever
Slotted screwdriver
Fluid drain pan
Brake hose clamp
Fluid line stopper
Brake bleeder kit
Brake caliper wind back tool
Car lift or jack with jack stands, and wheel chocks
Replacement: brake hose – VAUXHALL VIVARO Combi. AUTODOC experts recommend:
- Follow the maintenance intervals, recommendations, and requirements for using the part as specified by the manufacturer.
- For both the brake hoses and the caliper components, the replacement procedure is identical for the left and right sides of the axle.
- All the work should be carried out with the ignition switched off.
Replacement: brake hose – VAUXHALL VIVARO Combi. Recommended sequence of steps:
- Step 1Open the bonnet.Step 2
Loosen the brake fluid reservoir cap. - Step 3
Secure the wheels with chocks. - Step 4
Loosen the wheel fasteners. Use a 19 mm wheel impact socket. Use a tommy bar. - Step 5Raise the vehicle.Replacement: brake hose – VAUXHALL VIVARO Combi. AUTODOC recommends:If you are using a jack, make sure the car is parked on a hard, flat surface.Make sure to additionally secure the car with jack stands.Step 6
Unscrew the wheel fasteners.Caution!To avoid injury, hold up the wheel when unscrewing the fasteners. - Step 7
Remove the wheel. - Step 8
Prepare a fluid drain pan. - Step 9
Clean the areas where the brake hose is connected to the brake caliper and to the brake pipe. Use a wire brush. Use WD-40 spray. - Step 10
Detach the brake hose from the bracket on the suspension strut. - Step 11
Attach the brake hose clamp to the brake hose. - Step 12
Loosen the fastener that connects the brake hose to the brake caliper. Use an 14 mm combination spanner. - Step 13
Unscrew the nut fitting connecting the brake pipe to the brake hose. Use an 11 mm combination spanner. - Step 14
Block off the brake pipe. Use a fluid line stopper. - Step 15
Remove the brake hose from the bracket on the body. - Step 16
Remove the brake hose clamp from the brake hose. - Step 17
Unscrew the brake hose from the brake caliper. - Step 18
Attach the new brake hose to the brake caliper by screwing the brake hose nut fitting into the hole in the caliper. - Step 19
Securely tighten the brake hose connection to the brake caliper. Use a 14 mm flare nut socket. Use a torque wrench. Tightening torque: 14 N·m. - Step 20
Install the brake hose into the bracket on the body. - Step 21
Remove the fluid line stopper from the brake pipe. - Step 22.1
Screw the brake pipe nut fitting into the brake hose and tighten it. Use an 11 mm flare nut wrench.Step 22.2
Use an 11 mm flare nut socket. Use a torque wrench. Tightening torque: 44 N·m. - Step 23
Secure the brake hose in the bracket on the suspension strut. - Step 24
Remove the brake bleeder screw cap.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the VAUXHALL Vivaro Combi (X82) model
Popular maintenance tutorials for Vivaro X82
Free download PDF 2.29 MB
Free download PDF 1.85 MB
Free download PDF 1.73 MB
Free download PDF 1.68 MB
Free download PDF 7.06 MB
Free download PDF 1.44 MB
Complete guides for changing the Brake flexi hose on different VAUXHALL VIVARO models
Free download PDF 3.7 MB
Free download PDF 3.7 MB
Free download PDF 3.71 MB
Free download PDF 3.71 MB
Free download PDF 3.65 MB
Free download PDF 2.39 MB
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your VAUXHALL Vivaro Combi (X82)
View more
How to Fix a Squealing Belt: Causes & Solutions | AUTODOC Expert Tips
Revive Your Tyres: Expert Tips for a Lasting Shine | AUTODOC Guide
Top 5 Car Interior Cleaning Mistakes You Should Avoid | AUTODOC Tips
How to prevent car windows from fogging up | AUTODOC tips
Most commonly replaced car parts on VAUXHALL VIVARO
Time to replace parts? Get even better deals in our Shop app.
SCAN ME