Disclaimer
How to change front anti roll bar links on VW TIGUAN (5N_) – replacement guide
downloads:
1
Views:
16
Important!
This replacement procedure can be used for:
VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 2.0 TFSI, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 1.4 TSI 4motion, VW TIGUAN (5N_) 2.0 TSI 4motion, VW TIGUAN (5N_) 2.0 TSI 4motion, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 2.0 TFSI 4motion, VW TIGUAN (5N_) 2.0 TFSI 4motion, VW TIGUAN (5N_) 1.4 TSI 4motion, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 2.0 TDI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 2.0 TDI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 2.0 TDI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 1.4 TSI … View more
The steps may slightly vary depending on the car design.
VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 2.0 TFSI, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 1.4 TSI 4motion, VW TIGUAN (5N_) 2.0 TSI 4motion, VW TIGUAN (5N_) 2.0 TSI 4motion, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 2.0 TFSI 4motion, VW TIGUAN (5N_) 2.0 TFSI 4motion, VW TIGUAN (5N_) 1.4 TSI 4motion, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 2.0 TDI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 2.0 TDI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 2.0 TDI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 1.4 TSI, VW TIGUAN (5N_) 2.0 TDI 4motion, VW TIGUAN (5N_) 1.4 TSI … View more
The steps may slightly vary depending on the car design.
This video shows the replacement procedure of a similar car part on another vehicle
All the parts you need to replace – Anti Roll Bar Links for TIGUAN (5N_) and other VW models
Anti-roll bar link
Rod / Strut, wheel suspension
Repair Kit, stabilizer suspension
Repair Kit, stabilizer coupling rod
Mounting, stabilizer coupling rod
Anti-roll bar link
Rod / Strut, wheel suspension
Repair Kit, stabilizer suspension
Repair Kit, stabilizer coupling rod
Mounting, stabilizer coupling rod
Anti-roll bar link for VW TIGUAN (5N_) 2.0 TDI 4motion Diesel (140 hp)
Anti-roll bar link for VW TIGUAN (5N_) 2.0 TDI 4motion Diesel (170 hp)
Anti-roll bar link for VW TIGUAN (5N_) 2.0 TFSI 4motion Petrol (200 hp)
Wire brush
WD-40 spray
Brake cleaner
Ceramic grease
Copper grease
Torque wrench
Combination spanner #18
Combination spanner #19
Drive socket # 18
Drive socket # 19
XZN socket bit #6
HEX bit No.H5
Wheel impact socket #17
Ratchet wrench
Wheel chock
AUTODOC recommends:
- Replace the stabiliser links on VW TIGUAN (5N_) in pairs.
- The replacement procedure is identical for both stabiliser links on the same axle.
- Please note: all work on the car – VW TIGUAN (5N_) – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1Secure the wheels with chocks.Step 2
Loosen the wheel mounting bolts. Use wheel impact socket #17. - Step 3Raise the car.Replacement: anti roll bar links – VW TIGUAN (5N_). Professionals recommend:If you are using a jack, make sure it rests on a flat surface without any unevenness.Be sure to additionally secure the car with jack stands.Step 4
Unscrew the wheel bolts.AUTODOC recommends:Warning! To avoid injury, hold the wheel while unscrewing the fastening bolts. VW TIGUAN (5N_) - Step 5
Remove the wheel. - Step 6
Clean the stabiliser link fasteners. Use a wire brush. Use WD-40 spray. - Step 7
Unscrew the fastener connecting the stabilizer link to the shock strut. Use a drive socket #18. Use XZN #6. Use a ratchet wrench. - Step 8
Unscrew the fastener connecting the stabilizer link to the stabilizer bar. Use a combination spanner #18. Use XZN #6. Use a ratchet wrench. - Step 9
Remove the stabiliser link.Replacement: anti roll bar links – VW TIGUAN (5N_). Tip from AUTODOC experts:Examine stabiliser bushes. Replace them if needed. - Step 10
Clean the mounting seats of the stabiliser link. Use a wire brush. Use WD-40 spray. - Step 11
Install a new stabiliser link and tighten the fasteners. Use a combination spanner #19. Use HEX No.H5. Use a ratchet wrench. - Step 12
Tighten the fastener connecting the stabilizer link to the shock strut. Use a drive socket #19. Use a torque wrench. Tighten it to 65 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Popular maintenance tutorials for Tiguan Mk1
Free download PDF
2.77 MB
Free download PDF3.06 MB
Free download PDF2.59 MB
Free download PDF2.1 MB
Free download PDF2.55 MB
Free download PDF2.22 MB
Complete guides for changing the Drop links on different VW TIGUAN models
Free download PDF1.48 MB
Free download PDF2.08 MB
Free download PDF2.06 MB
Free download PDF972.8 KB
Free download PDF1.99 MB
Free download PDF2.01 MB
Your profile is your personal assistant.
It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents
Install the AUTODOC CLUB app!
Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.
Scan
To download the app:
- - scan the QR code
- - download from App Store
- - download from Google Play
Tips & tricks for your VW TIGUAN (5N_)
View more
How and why to check your oil | AUTODOC tips
Coolant comparison test | AUTODOC
How to choose the right engine oil for your car | AUTODOC
How to remove scratches from car plastic | AUTODOC tips
