Recommended replacement interval for the part category Oil filter : 12 month / 15000 km

Important!

This replacement procedure can be used for:
FIAT BRAVO II (198) 1.6 D Multijet (198AXM1B) … View more

The steps may slightly vary depending on the car design.

How to change oil filter and engine oil on FIAT BRAVO 2 (198) [TUTORIAL AUTODOC]

All the parts you need to replace – Oil Filter for BRAVO II (198) and other FIAT models

Oil filter

Oil filter for FIAT BRAVO II (198) 1.6 D Multijet (198AXM1B) Diesel (90 hp)

Replacement: engine oil and filter – Fiat Bravo 2. Tools you might need:

                        All-purpose cleaning spray
                      
                        Oil filter cup socket 76/14-F
                      
                        Drive socket # 10 
                      
                        Drive socket # 17 
                      
                        Ratchet wrench
                      
                        Torque wrench
                      
                        Phillips Screwdriver
                      
                        Flat Screwdriver
                      
                        Funnel
                      
                        Oil drain pan
                      
                        Hydraulic transmission jack
                      
                        Fender cover

Buy tools

AUTODOC recommends:

Replace the oil filter every time when changing motor oil.
Wear gloves to prevent contact with hot liquid.
All work should be done with the engine stopped.

Replacement: engine oil and filter – Fiat Bravo 2. Take the following steps:

Step 1

Open the hood.
Step 2

Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
Step 3

Unscrew the oil filler plug.
Step 4

Lift the car using a jack or place it over an inspection pit.

Replacement: engine oil and filter – Fiat Bravo 2. Tip from AUTODOC experts:
The vehicle must be on even keel, and if it is at an angle, the drain plug must be at the lowest point.
Step 5

Undo the fasteners of the oil pan lower cover. Use a drive socket #10. Use a ratchet wrench. Use a Phillips screwdriver.

Replacement: engine oil and filter – Fiat Bravo 2. Tip from AUTODOC:
To avoid injury, hold the engine skid plate cautiously tight when unscrewing the fasteners and when lowering the hydraulic transmission jack.
Step 6

Support the engine skid plate. Use a hydraulic transmission jack.
Step 7

Remove the oil pan cover. Remove the hydraulic transmission jack.

Replacement: engine oil and filter – Fiat Bravo 2. AUTODOC experts recommend:
Lower the hydraulic transmission jack smoothly, without jerks, to avoid damaging assemblies and mechanisms.
Step 8

Unscrew the wheel arch cover fasteners. Use a drive socket #10. Use a ratchet wrench. Use a Phillips screwdriver.
Step 9

Put a waste oil container with at least 5 l capacity under the drainage hole.
Step 10

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 11

Unscrew the drain plug. Use a drive socket #17. Use a ratchet wrench.
Step 12

Drain the used oil.

Replacement: engine oil and filter – Fiat Bravo 2. AUTODOC recommends:
Caution! The oil may be hot.
Step 13

Prepare a container for the old oil filter.
Step 14

Unscrew the filter housing cap together with the old filter element.

Step 15

Put the old oil filter in the container.

Replacement: engine oil and filter – Fiat Bravo 2. Tip:
Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter.
Step 16

Detach the oil filter from the filter cover.
Step 17

Remove the oil filter cover O-ring. Use a flat screwdriver.
Step 18

Clean the oil filter housing cap. Use all-purpose cleaning spray.
Step 19

Install the new oil filter to the mounting seat on the filter cover.

Please note!
Make sure to install the filter correctly. Don't mix up the sides of the part.Wait until the oil has completely drained from the drainage hole.
Step 20

Install a new O-ring to its mounting seat on the filter cover.
Step 21

Lubricate the rubber seal of the new filter with a little amount of fresh oil.
Step 22

Screw the new filter into its place.
Step 23

Install a new oil filter housing cover and tighten it. Use the 76/14-F socket. Use a torque wrench. Tighten it to 25 Nm torque.

Replacement: engine oil and filter – Fiat Bravo 2. Professionals recommend:
Wait until the oil has completely drained from the drainage hole.
Step 24

Clean the area of the oil pan drainage hole.
Step 25

Screw in the new drainage plug and tighten it. Use a drive socket #17. Use a torque wrench. Tighten it to 22 Nm torque.
Step 26

Clean the area of the oil pan drainage hole. Use all-purpose cleaning spray.
Step 27

Install the wheel arch cover to its mounting seat. Screw in the fasteners. Use a drive socket #10. Use a ratchet wrench. Use a Phillips screwdriver.
Step 28

Reinstall the oil pan lower cover.
Step 29

Tighten the fasteners of the oil pan lower cover. Use a drive socket #10. Use a ratchet wrench. Use a Phillips screwdriver.
Step 30

Lower the car.

Step 31

Remove the oil filler cap. Insert the funnel.
Step 32

Pour oil into the engine through the filler. Required amount of oil: 4.6 l.

Replacement: engine oil and filter – Fiat Bravo 2. AUTODOC recommends:
Use the oil recommended by the manufacturer.
Step 33

Check the oil level using the dipstick. Top up oil if necessary.

Please note!
The oil level should be between the Min and Max marks.
Step 34

Tighten the oil filler cap.
Step 35

Run the engine for a few minutes. After the oil pressure warning light goes out, stop the engine.
Step 36

Check the oil level 5 minutes after the stop of the engine operation using a dipstick and add oil if necessary.

Please note!
The oil level should be between the Min and Max marks.Make sure that the oil filler cap is properly tightened.Check the threaded plug of the drainage hole and the oil filter seal for tightness. If necessary, carefully tighten them up.
Step 37

Remove the fender protection cover.
Step 38

Close the hood.

Replacement: engine oil and filter – Fiat Bravo 2. Tip from AUTODOC:
Note that oil pressure warning light, which indicates insufficient pressure in the lubrication system, may be on for a longer time than usual. After a few seconds, the oil will fill all the channels, and the light will go out. To protect the environment from pollution, be sure to dispose of the used filters at special collection points.

Was this manual helpful?

Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.

How to change fuel filter on Fiat Bravo 2 – replacement guide

Free download PDF
1.61 MB
How to change pollen filter on Fiat Bravo 2 – replacement guide

Free download PDF
1.24 MB
How to change air filter on Fiat Bravo 2 – replacement guide

Free download PDF
993.28 KB
How to change front brake pads on Fiat Bravo 2 – replacement guide

Free download PDF
1.93 MB
How to change rear brake pads on Fiat Bravo 2 – replacement guide

Free download PDF
1.7 MB
How to change front brake discs on Fiat Bravo 2 – replacement guide

Free download PDF
2.48 MB

How to change engine oil and filter on FIAT BRAVA (182) – replacement guide

Free download PDF
1.88 MB
How to change engine oil and filter on FIAT BRAVO I (182) – replacement guide

Free download PDF
1.88 MB
How to change engine oil and filter on a car – replacement tutorial

Universal

Free download PDF
2.82 MB
How to change engine oil and filter on Fiat Panda 169 – replacement guide

Free download PDF
1.91 MB
How to change engine oil and filter on Fiat Punto 199 – replacement guide

Free download PDF
2.37 MB
How to change engine oil and filter on Fiat 500 312 – replacement guide

Free download PDF
2.25 MB

Your profile is your personal assistant.

It can track car expenses, keep a car log and replacement schedule, and save favourite materials, notes and documents

Install the AUTODOC CLUB app!

Your personal car expenses manager, maintenance tips, reminders about upcoming appointments and service intervals, DIY repair instructions – all this on your phone.

Scan

To download the app:

- scan the QR code
- download from App Store
- download from Google Play

Checking the starter without removing it | AUTODOC tips

19K views

Published on: 01/12/2020
How to start a car after a long idle period | AUTODOC tips

6K views

Published on: 20/05/2021
How to repair a chipped or cracked windscreen | AUTODOC tips

7K views

Published on: 14/12/2023
How to repair a bumper yourself | AUTODOC tips

9K views

Published on: 01/06/2023