Disclaimer
How to change engine oil and filter on Opel Meriva X03 – replacement guide
downloads:
33
Views:
477
Recommended replacement interval for the part category Oil filter : 1 year / 30000 km
Important!
This replacement procedure can be used for:
OPEL Meriva A (X03) 1.8 (E75), OPEL Meriva A (X03) 1.6 (E75), OPEL Meriva A (X03) 1.6 (E75) … View more
The steps may slightly vary depending on the car design.
OPEL Meriva A (X03) 1.8 (E75), OPEL Meriva A (X03) 1.6 (E75), OPEL Meriva A (X03) 1.6 (E75) … View more
The steps may slightly vary depending on the car design.
How to change oil filter and engine oil on OPEL MERIVA A [TUTORIAL AUTODOC]

All the parts you need to replace – Oil Filter for Meriva A (X03) and other OPEL models
Alternative products

Wire brush
All-purpose cleaning spray
Torque wrench
Torx bit T40
Oil filter cup socket 76-F14
Ratchet wrench
Oil drain pan
Funnel
Fender cover
Replacement: engine oil and filter – Opel Meriva X03. AUTODOC recommends:
- Replace the oil filter every time when changing motor oil.
- Wear gloves to prevent contact with hot liquid.
- Please note: all work on the car – Opel Meriva X03 – should be done with the engine switched off.
Carry out replacement in the following order:
- Step 1
Open the hood. - Step 2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car. - Step 3
Unscrew the oil filler plug. - Step 4
Lift the car using a jack or place it over an inspection pit. - Step 5
Put a waste oil container with at least 4 l capacity under the drainage hole. - Step 6
Clean the area of the oil pan drainage hole. Use a wire brush. Use all-purpose cleaning spray. - Step 7
Unscrew the drain plug. Use Torx T40. Use a ratchet wrench. - Step 8
Drain the used oil.Replacement: engine oil and filter – Opel Meriva X03. Professionals recommend:Caution! The oil may be hot. - Step 9
Clean the oil filter. Use all-purpose cleaning spray. - Step 10
Unscrew the oil filter. Use the 76-F14 socket. Use a ratchet wrench. - Step 11
Put the old oil filter in the container.Replacement: engine oil and filter – Opel Meriva X03. Tip from AUTODOC experts:Move up the container. The oil starts to drain out of the drainage hole immediately after you have removed the oil filter. - Step 12
Lubricate the rubber seal of the new filter with a little amount of fresh oil. - Step 13
Install a new oil filter.Please note!Make sure to install the filter correctly. Don't mix up the sides of the part. - Step 14
Tighten the oil filter. Remember to observe the recommended tightening torque. Use the 76-F14 socket. Use a torque wrench. Tighten it to 18 Nm torque.Replacement: engine oil and filter – Opel Meriva X03. Tip:Wait until the oil has completely drained from the drainage hole. - Step 15
Clean the area of the oil pan drainage hole. - Step 16
Screw in the new drainage plug and tighten it. Use Torx T40. Use a torque wrench. Tighten it to 24 Nm torque.
Was this manual helpful?
Please rate this manual on a scale from 1 to 5. If you have any questions, feel free to ask us.
Users voted – 0
Need New Tyres?
Find out which tyre and wheel sizes are compatible with the OPEL Meriva A (X03) model
Popular maintenance tutorials for Opel Meriva x03
Complete guides for changing the Oil filters on different OPEL MERIVA models
Unlock your car maintenance assistant!
Track expenses, manage logs, schedule replacements, and more.
Tips & tricks for your OPEL Meriva A (X03)
View more
What to do if your check engine light is on | AUTODOC tips
How to Prevent Premature Wear on Your Car Boot Damper | AUTODOC
Coolant comparison test | AUTODOC
Checking the starter without removing it | AUTODOC tips
Most commonly replaced car parts on OPEL MERIVA
Time to replace parts? Get even better deals in our Shop app.

SCAN ME



























